XtremepowerUS 75166 Original instruction manual

PARTNO. ITEMNO. DESCRIPTION QTY
1 47151001 Treads 2
2 5760101000 Hinges 2
3 47151006 Small support 1
4 5760100000 Storageliner 1
5 47151003 SideWalls 2
6 5760102080 Foam Strip 1
7 47151005 MediumSupport 1
8 47151004 Big Support 1
9 5212012000 ScrewsST4.8*20) 16
10 5244006000 Gasket 10
11 5212005000 Screws(ST3.9*11.6) 8
1

ToolsNeeded
Rubber Mallet; CordlessDrill; Drill Bit
2.Warning and Caution
a) Check building codes/premitting
Please consult yourlocalBuildingDepartment beforeinstallation of yourstep and equipmentin
ordertoreduce the risk of drowning, electrocution,falls, or otherserious injuryordeath.
Equipment installation must complywiththe codes ofauthorityhavingjurisdiction and may
requirepermits(e,g.,building, plumbing, electrical, zoning, etc.).Be surethat barriers (fences,
gates, etc.) restrictingspaaccess meet localcodes.
b) Use for intended purposeonly
Notintendedforstoring hazardous products(such as chemicals),which is nota securelocation.
c) Check thatyou haveall required parts
Check thecontents of the carton withtheparts list forthestep.All parts and hardwareare
required.DO NOTattempt toassembleorinstall thestep ifany parts missing.
d) Selectan appropriatelocation
TheStep must belocated on alevelsolidbaseandinalocation thatwillbe in full viewof
competent adult supervision wheninuse.
e) Followallinstructions
-All instructions must be followed completelyas themanualshownforstable correct assembly
andinstallation.
- Use the handtools andequipment appropriatelyaccordingtothe manufacturer s
recommendations. CORDLESS DRILLONLY. DONOTusea corded drill inoraroundthepools
inordertolowerthe risks ofelectrocution.
f)Lift safely
Haveanotherpersontohelpwhen liftingawkwardorheavy loads.
g) Doublecheckafter installation
Afterwell assembledand installationed,pleasedoublecheck theinstructions and procedures
tomakesurenothinghas beenoverlookedbeforestartingto use the step.
2

Drill 5MM
Drill 3.5MM
Drill 3.5MM
STEP 1: Install 2 self-adhesive pads on each of
the sidewalls.
STEP 2: Pre-drill φ5mm pilot holes at the end of
the three supports. See image above.
STEP 3: Mark the position on both big and small
supports and the two sidewalls and pre-drill
φ3.5mm pilot holes.
STEP 4: Place the medium support over the two
locking tabs on the sidewalls. Tap down with the
mallet until seated on the locking tabs. Secure
the support at both ends using 2 x ST4.8*20
screws.
STEP 5: Place the large support over the two
locking tabs with the groove facing up. Tap down
with a rubber mallet until seated on the locking
tabs.
STEP 6: Use 2 x ST4.8*20 screws to seal both
ends of the support.
3

4
STEP 7: Place the tapered edge into the groove of the big support to install the bottom tread.
Apply pressure to force the tapered edge into the groove. Tap the front of the tread with the
rubber mallet while holding the tread in place. Tap down gently on the top of the tread until sealed
on the locking tabs.
STEP 8: Place the hinge (barrel side up) over
the mortised area of the small support. Attach 2 x
ST3.9*11.6 screws to fix up the hinge. No need to
drill the pilot holes. Please repeat to attach the
second hinge.
STEP 9: Place the tread on a flat surface
with the bottom facing up. Place the hinges
over the mortised area on the treads and fix
with 2 x ST3.9*11.6 screws in each hinge.
STEP 10: Place the small support on the
convex platform at the back of the sidewall,
then tap down with a rubber mallet until
seated onto the locking tabs.

Warning:Toreducetherisk ofdrowning,falls,paralysis,electrocution, orother serious injuryor
death,use the stepsystemproperly.
• Use forintendedpurpose only, no intendforchemicalstorage.
• Nodivingorjumpingfromsteps, risk of paralysis ordeath.
• Onlyone personallowed onthe step systemat atime.
• Illuminatethesteps when usingthestepsystemat night.
• Weightlimited-300lbs., exceedingmaximumweightmaycause thestep broken.
• Securethe spawhen notinuse. Pleaserefertolocalcodes.(E.g.withalocked coverorsecure
gate)
• Take careofthe children at all times when theyareinoraroundwatertohelp prevent drowning.
• Be sureandsafe.Themanufactureis notresponsibleforimproper assembly,installationand use.
Off state Open state
5
STEP 11: Secure both ends of the sidewall
with 2 x ST4.8*20 screws.
STEP 12: Open the above tread and place
the storage liner into the tread and fix with
screws and gaskets.

6