Xylem GSP0311 User manual

INSTRUCTION MANUAL
Sump and Effluent
Pump

Table of Contents
1 Introduction and Safety..............................................................................................................2
1.1 Introduction.......................................................................................................................... 2
1.2 Safety..................................................................................................................................... 2
1.2.1 Safety terminology and symbols.................................................................................2
1.2.2 User safety......................................................................................................................3
1.3 Protecting the environment................................................................................................4
2 Transportation and Storage...................................................................................................... 5
2.1 Inspect the delivery..............................................................................................................5
2.1.1 Inspect the package..................................................................................................... 5
2.1.2 Inspect the unit..............................................................................................................5
3 Product Description....................................................................................................................6
3.1 General description............................................................................................................. 6
3.2 Operational specifications.................................................................................................. 6
3.3 Recommended options.......................................................................................................6
4 Installation....................................................................................................................................9
4.1 Preinstallation....................................................................................................................... 9
4.1.1 Pump location guidelines............................................................................................ 9
4.1.2 Piping checklist........................................................................................................... 10
4.2 Typical installation............................................................................................................. 10
4.3 Wiring and grounding.......................................................................................................10
4.4 Install the pump................................................................................................................. 11
5 Operation.................................................................................................................................. 12
5.1 Start the pump....................................................................................................................12
6 Maintenance..............................................................................................................................13
6.1 Maintenance guidelines....................................................................................................13
7 Troubleshooting....................................................................................................................... 14
7.1 Operation troubleshooting.............................................................................................. 14
8 Product warranty...................................................................................................................... 15
Table of Contents
Sump and Effluent Pump INSTRUCTION MANUAL 1

1 Introduction and Safety
1.1 Introduction
Purpose of this manual
The purpose of this manual is to provide necessary information for:
• Installation
• Operation
• Maintenance
CAUTION:
Read this manual carefully before installing and using the product. Improper use of the
product can cause personal injury and damage to property, and may void the warranty.
NOTICE:
Save this manual for future reference, and keep it readily available at the location of the
unit.
1.2 Safety
WARNING:
• The operator must be aware of safety precautions to prevent physical injury.
• Operating, installing, or maintaining the unit in any way that is not covered in this
manual could cause death, serious personal injury, or damage to the equipment. This
includes any modification to the equipment or use of parts not provided by Xylem. If
there is a question regarding the intended use of the equipment, please contact a
Xylem representative before proceeding.
• Do not change the service application without the approval of an authorized Xylem
representative.
CAUTION:
You must observe the instructions contained in this manual. Failure to do so could result
in physical injury, damage, or delays.
1.2.1 Safety terminology and symbols
About safety messages
It is extremely important that you read, understand, and follow the safety messages and
regulations carefully before handling the product. They are published to help prevent
these hazards:
• Personal accidents and health problems
• Damage to the product and its surroundings
• Product malfunction
Hazard levels
Hazard level Indication
DANGER:
A hazardous situation which, if not avoided, will result in
death or serious injury
1 Introduction and Safety
2 Sump and Effluent Pump INSTRUCTION MANUAL

Hazard level Indication
WARNING:
A hazardous situation which, if not avoided, could result
in death or serious injury
CAUTION:
A hazardous situation which, if not avoided, could result
in minor or moderate injury
NOTICE:
Notices are used when there is a risk of equipment
damage or decreased performance, but not personal
injury.
Special symbols
Some hazard categories have specific symbols, as shown in the following table.
Electrical hazard Magnetic fields hazard
Electrical Hazard: CAUTION:
1.2.2 User safety
General safety rules
These safety rules apply:
• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash
hazards.
• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.
Safety equipment
Use safety equipment according to the company regulations. Use this safety equipment
within the work area:
• Hard hat
• Safety goggles, preferably with side shields
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection
• First-aid kit
• Safety devices
NOTICE:
Never operate a unit unless safety devices are installed. Also see specific information
about safety devices in other chapters of this manual.
Electrical connections
Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local regulations. For more information about
requirements, see sections dealing specifically with electrical connections.
1 Introduction and Safety
Sump and Effluent Pump INSTRUCTION MANUAL 3

1.3 Protecting the environment
Emissions and waste disposal
Observe the local regulations and codes regarding:
• Reporting of emissions to the appropriate authorities
• Sorting, recycling and disposal of solid or liquid waste
• Clean-up of spills
Exceptional sites
CAUTION: Radiation Hazard
Do NOT send the product to Xylem if it has been exposed to nuclear radiation, unless
Xylem has been informed and appropriate actions have been agreed upon.
Recycling guidelines
Always follow local laws and regulations regarding recycling.
1 Introduction and Safety
4 Sump and Effluent Pump INSTRUCTION MANUAL

2 Transportation and Storage
2.1 Inspect the delivery
2.1.1 Inspect the package
1. Inspect the package for damaged or missing items upon delivery.
2. Note any damaged or missing items on the receipt and freight bill.
3. File a claim with the shipping company if anything is out of order.
If the product has been picked up at a distributor, make a claim directly to the
distributor.
2.1.2 Inspect the unit
1. Remove packing materials from the product.
Dispose of all packing materials in accordance with local regulations.
2. Inspect the product to determine if any parts have been damaged or are missing.
3. If applicable, unfasten the product by removing any screws, bolts, or straps.
For your personal safety, be careful when you handle nails and straps.
4. Contact the local sales representative if there is any issue.
2 Transportation and Storage
Sump and Effluent Pump INSTRUCTION MANUAL 5

3 Product Description
3.1 General description
Description
Sump pumps are designed to run intermittently and usually seasonally.
Intended applications
WARNING:
California Proposition 65 warning! This product contains chemicals known to the state of
California to cause cancer and birth defects or other reproductive harm.
Specially designed for the following uses:
• Basement draining
• Water transfer
•Effluent transfer
• Filtered effluent
3.2 Operational specifications
Limitations
Model Discharge size Capacities Maximum head Solids handling Maximum
temperature
(continuous
operation)
GSP0311 11/2” NPT to 43 GPM to 22’ TDH 1/2” spherical 104°F (40°C)
GSP0511 11/2” NPT to 71GPM to 24’ TDH 1/2” spherical 104°F (40°C)
Mechanical seal types
Model Description
GSP Silicon carbide/carbon/BUNA
3.3 Recommended options
The following options are strongly recommended for added protection when the loss of
pump function will result in property damage.
3 Product Description
6 Sump and Effluent Pump INSTRUCTION MANUAL

Warning device alarms
Table 1: Model information
Alarm
order no.
Agency
listing
NEMA
rating3Float switch
included
Float
switch
length
Power
cord
length
Audible
alarm
type/db at
10’
Primary
power
Hertz Voltage to
float
switch
Battery
backup
alarm
Additional
features
A4–2 UL, CSA N1 10’ 6’ Horn / 87
120 VAC
60 9 VDC Yes
TAN1M* UL CSA
15’
Horn / 88 50/60 12 VAC No
TAN3M* UL, CSA N3R
N/A
Horn / 85
120 VAC No
TAN4M* N4X Horn / 88
TAABW FCC
N1 Yes
10’
6’ Horn / 87
60
9 VDC Yes
1
TAABWUL
FCC
TAABP
10’2
2
LAN1 UL, CSA Order
separately N/A
Bell / 88
120 VDC No
LAN4 UL, CSA N4X No Horn / 95
@ 2’
* M = Mechanical SignalMaster Switch
1This device is wireless and will transmit a signal up to 150’ between the transmitter and the alarm, it requires line of sight clearance between
the transmitter and the alarm panel, i.e. (no hills in between).
2The TAABP has a 120V, NEMA 5–15R, 13.8 Amp Max. receptacle on the bottom to accommodate a pump plug.
3N1 = indoor, N3R = raintight (outdoor), N4X = watertight (outdoor) and Corrosion resistant (fiberglass).
Battery backup sump pump
Specifications:
• 12 volt pump
• Float switch
• 10 amp battery charger
• Check valve
• Pipe fittings
• Battery box is 7.5” W, 14.5” L, 8” D and is sized for Group 24–30 batteries
• System requires minimum 105 amp deep cycle marine battery, Series 27 (not
included)
Table 2: Performance chart
Model Discharge height GPH Battery life
SPBB
5’ 1380 9 hours
10’ 900 9 hours
13’ 480 11 hours
SPBB2
5’ 2250 7 hours
10’ 1500 8 hours
13’ 1000 9 hours
3 Product Description
Sump and Effluent Pump INSTRUCTION MANUAL 7

NOTICE:
Failure to install a warning device or a suitable back up sump pump may lead to property
damage when there is a loss of pump function in the main sump pump.
3 Product Description
8 Sump and Effluent Pump INSTRUCTION MANUAL

4 Installation
4.1 Preinstallation
WARNING:
• Disconnect and lock out electrical power before installing or servicing the unit to
prevent unexpected start-up.
• Do NOT install this pump in swimming pools or marine areas.
• Risk of electric shock. This pump is supplied with a grounding conductor and
grounding-type attachment plug. Install or connect to a circuit that is protected by a
GFCI, ground fault circuit interruptor.
• This pump requires separate, properly fused and grounded branch circuit.
• Electrical supply must be in accordance with the specifications given on the pump’s
nameplate.
• Failure to follow these instructions could result in serious personal injury, death and/or
property damage.
These general requirements apply:
• The electrical outlet must be within the length limitations of the pump power cord and
at least four feet above floor level to minimize possible hazards from floor conditions.
• Do not use pumps in water over 140°F (60°C)
• Do not use pumps in mud, sand, cement, oil, or chemicals.
• Do not use a sump pump as a trench or excavation pump, or for pumping sewage,
gasoline, or other hazardous liquids.
• Do not modify the pump in any way.
• Do not lift or carry the pump by the power cord.
• Do not remove any tags from pump or cords.
• Do consider a two pump system with an alarm where an installation may become
overloaded.
• Do inspect and test system for proper operations at least every three months.
• Always verify that the pump nameplate Amps, Voltage, Phase, HP rating match the
power supply.
• Be sure to record the model numbers and serial numbers from the pump for future
reference.
4.1.1 Pump location guidelines
Guideline Explanation
Make sure that the space around the pump and switch
are sufficient.
The switch must be able to operate freely.
The depth must be deeper than the minimum depth at
which the switch turns the pump on.
As an example, if the pump turns on at 7.50”, the basin
must be deeper than 7.50”.
Determine whether a cover is required. Install a cover when:
• Installation is in an area where debris could enter
and clog the pump.
• In a traffic area such as a basement where children
and pets are allowed. A bolt-on or child-proof cover is
recommended.
4 Installation
Sump and Effluent Pump INSTRUCTION MANUAL 9

4.1.2 Piping checklist
Guideline Explanation
Discharge pipe should be the same size as the pump. This insures optimum performance. Undersized pipe can
dramatically reduce the flow and waste energy.
4.2 Typical installation
Typical pump installation in sump; Tether float shown, float not needed on models with
included float.
12
3
4
5
6
7
8
9
1. Pump electrical plug
2. Piggyback switch plug
3. Grounded wall outlet
4. Float switch
5. Pumping range
6. 1/8” “Relief” hole
7. Union
8. Check valve
9. Pump position
4.3 Wiring and grounding
WARNING:
• Make sure that you have grounded (earthed) the pump, the drive unit, and the controls
before connecting the electrical power.
• Install, earth (ground), and wire the equipment according to the local and National
Electrical Code Requirements.
• Install a power switch near the pump that disconnects all the conductors.
• Disconnect and lock out electrical power before installing or servicing the unit.
• Electrical supply must be in accordance with the specifications given on the pump’s
nameplate.
• All splices must be waterproof. If using splice kits, follow manufacturer’s instructions.
• Select the correct type and NEMA grade junction box for the application and location.
The junction box must insure dry, safe wiring connections.
• Seal all controls from gases present which may damage electrical components.
• Failure to permanently ground the pump, motor and controls before connecting to
power can cause shock, burns, or death.
4 Installation
10 Sump and Effluent Pump INSTRUCTION MANUAL

NOTICE:
• Use only copper wire to the drive unit and the ground (earth) . The ground (earth) wire
must be at least as thick as the wire to the drive unit.
• Conductors should have color codes to make the maintenance easier.
4.4 Install the pump
DO NOT place the pump directly on earth, gravel or debris. This can cause excessive wear
of the impeller and possible jamming.
A. Provide a hard level bottom of bricks or concrete.
B. Remove all debris from the bottom of the sump pit.
1. Install a threaded pipe adapter into the threaded pump discharge.
2. Install a line check valve just above the union to prevent backflow of water after each
pump cycle.
3. Connect the discharge pipe to the pump.
4. Lower the pump into the pit, making sure the float switch has adequate clearance and
will not hang up on the pit wall. See “Typical installation”.
The float must be free to move and not come in contact with the pump body, piping,
or other objects.
5. Securely tape or clamp power cord to discharge pipe, clear of the float mechanisms.
4 Installation
Sump and Effluent Pump INSTRUCTION MANUAL 11

5 Operation
5.1 Start the pump
1. Turn the power On at the breaker panel and/or the disconnect switch.
2. Fill the basin with water and observe the level of water where the pump turns On and
Off. The pump should go On well before the water overflows the top of the sump. The
pump should go Off before the water gets below the pump suction.
3. Install a cover on the sump pump basin if there is a danger of debris, children, or pets
falling into the basin.
5 Operation
12 Sump and Effluent Pump INSTRUCTION MANUAL

6 Maintenance
6.1 Maintenance guidelines
• Check frequently for debris and/or build-up which can interfere with pump or float
operation.
• Test pump periodically throughout the seasons.
1. Fill sump with water.
2. Check for debris and proper switch operation.
3. Remove debris which could clog the suction strainer or jam the switch.
4. Insure that the switch operates freely and does not hit the sump wall or hang-up on
piping or power cords.
NOTICE:
Failure to follow the maintenance guidelines, including to test unit periodically, may lead
to property damage due to loss of pump function.
6 Maintenance
Sump and Effluent Pump INSTRUCTION MANUAL 13

7 Troubleshooting
7.1 Operation troubleshooting
Symptom Cause Remedy
Motor not running Tripped thermal protector Check that all pump functions and
components are operating correctly. Allow the
unit to cool for 30 minutes. If the thermal
protector does not reset and no other
causation exists, replace the pump.
Open circuit breaker or blown fuse Check that the unit is securely plugged in.
Have an electrician check all wiring for proper
connections and adequate voltage and fuse
sizes.
Defective motor Replace the pump.
Low voltage If the voltage is under the recommended
minimum, check the size of the wiring from
the main switch on the property. If the main
switch is up to code, contact power company or
hydro authority.
Pump clogged Flush the piping system and clean the pump
casing.
Little or no liquid delivered Air locked Turn off the pump, clean out the anti-airlock
hole, restart the pump.
Low voltage If the voltage is under the recommended
minimum, check the size of the wiring from
the main switch on the property. If the main
switch is up to code, contact power company or
hydro authority.
System head too high Purchase different pump or adjust system.
Pump clogged / rotating parts binding Flush the piping system and clean the pump
casing.
Improper check valve direction Remove check valve and examine for freedom
of operation and proper installation.
Pump will not turn off System head too high Purchase different pump or adjust system.
Pump clogged Flush the piping system and clean the pump
casing.
Level control defective or switch not properly
positioned
Install pump as shown in installation section. If
problem persists, replace switch.
Improper check valve direction Remove check valve and examine for freedom
of operation and proper installation.
Inflow excessive for size of pump Purchase different pump appropriate for your
system.
Pump cycles constantly Level control defective or switch not properly
positioned
Install pump as shown in installation section. If
problem persists, replace switch.
Check valve leaking Remove check valve and examine for freedom
of operation and proper installation.
Incorrect size basin or wet-well Adjust system or replace basin with
appropriate size.
Inflow excessive for size of pump Purchase different pump appropriate for your
system.
7 Troubleshooting
14 Sump and Effluent Pump INSTRUCTION MANUAL

8 Product warranty
Commercial warranty
Warranty. For goods sold to commercial buyers, Seller warrants the goods sold to Buyer
hereunder (with the exception of membranes, seals, gaskets, elastomer materials,
coatings and other "wear parts" or consumables all of which are not warranted except as
otherwise provided in the quotation or sales form) will be (i) be built in accordance with
the specifications referred to in the quotation or sales form, if such specifications are
expressly made a part of this Agreement, and (ii) free from defects in material and
workmanship for a period of twenty-four (24) months from the date of installation or thirty
(30) months from the date of shipment (which date of shipment shall not be greater than
sixty (60) days after receipt of notice that the goods are ready to ship), whichever shall
occur first, unless a longer period is specified in the product documentation (the
“Warranty”).
Except as otherwise required by law, Seller shall, at its option and at no cost to Buyer,
either repair or replace any product which fails to conform with the Warranty provided
Buyer gives written notice to Seller of any defects in material or workmanship within ten
(10) days of the date when any defects or non-conformance are first manifest. Under
either repair or replacement option, Seller shall not be obligated to remove or pay for the
removal of the defective product or install or pay for the installation of the replaced or
repaired product and Buyer shall be responsible for all other costs, including, but not
limited to, service costs, shipping fees and expenses. Seller shall have sole discretion as to
the method or means of repair or replacement. Buyer’s failure to comply with Seller’s
repair or replacement directions shall terminate Seller’s obligations under this Warranty
and render the Warranty void. Any parts repaired or replaced under the Warranty are
warranted only for the balance of the warranty period on the parts that were repaired or
replaced. Seller shall have no warranty obligations to Buyer with respect to any product or
parts of a product that have been: (a) repaired by third parties other than Seller or without
Seller’s written approval; (b) subject to misuse, misapplication, neglect, alteration,
accident, or physical damage; (c) used in a manner contrary to Seller’s instructions for
installation, operation and maintenance; (d) damaged from ordinary wear and tear,
corrosion, or chemical attack; (e) damaged due to abnormal conditions, vibration, failure
to properly prime, or operation without flow; (f) damaged due to a defective power
supply or improper electrical protection; or (g) damaged resulting from the use of
accessory equipment not sold or approved by Seller. In any case of products not
manufactured by Seller, there is no warranty from Seller; however, Seller will extend to
Buyer any warranty received from Seller’s supplier of such products.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER
EXPRESS OR IMPLIED WARRANTIES, GUARANTEES, CONDITIONS OR TERMS OF
WHATEVER NATURE RELATING TO THE GOODS PROVIDED HEREUNDER, INCLUDING
WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY EXPRESSLY DISCLAIMED
AND EXCLUDED. EXCEPT AS OTHERWISE REQUIRED BY LAW, BUYER’S EXCLUSIVE
REMEDY AND SELLER’S AGGREGATE LIABILITY FOR BREACH OF ANY OF THE
FOREGOING WARRANTIES ARE LIMITED TO REPAIRING OR REPLACING THE PRODUCT
AND SHALL IN ALL CASES BE LIMITED TO THE AMOUNT PAID BY THE BUYER FOR THE
DEFECTIVE PRODUCT. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY OTHER FORM
OF DAMAGES, WHETHER DIRECT, INDIRECT, LIQUIDATED, INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, EXEMPLARY OR SPECIAL DAMAGES, INCLUDING BUT
NOT LIMITED TO LOSS OF PROFIT, LOSS OF ANTICIPATED SAVINGS OR REVENUE,
LOSS OF INCOME, LOSS OF BUSINESS, LOSS OF PRODUCTION, LOSS OF
OPPORTUNITY OR LOSS OF REPUTATION.
8 Product warranty
Sump and Effluent Pump INSTRUCTION MANUAL 15

Limited consumer warranty
Warranty. For goods sold for personal, family or household purposes, Seller warrants the
goods purchased hereunder (with the exception of membranes, seals, gaskets, elastomer
materials, coatings and other "wear parts" or consumables all of which are not warranted
except as otherwise provided in the quotation or sales form) will be free from defects in
material and workmanship for a period of twenty-four (24) months from the date of
installation or thirty (30) months from the product date code, whichever shall occur first,
unless a longer period is provided by law or is specified in the product documentation
(the “Warranty”).
Except as otherwise required by law, Seller shall, at its option and at no cost to Buyer,
either repair or replace any product which fails to conform with the Warranty provided
Buyer gives written notice to Seller of any defects in material or workmanship within ten
(10) days of the date when any defects or non-conformance are first manifest. Under
either repair or replacement option, Seller shall not be obligated to remove or pay for the
removal of the defective product or install or pay for the installation of the replaced or
repaired product and Buyer shall be responsible for all other costs, including, but not
limited to, service costs, shipping fees and expenses. Seller shall have sole discretion as to
the method or means of repair or replacement. Buyer’s failure to comply with Seller’s
repair or replacement directions shall terminate Seller’s obligations under this Warranty
and render this Warranty void. Any parts repaired or replaced under the Warranty are
warranted only for the balance of the warranty period on the parts that were repaired or
replaced. The Warranty is conditioned on Buyer giving written notice to Seller of any
defects in material or workmanship of warranted goods within ten (10) days of the date
when any defects are first manifest.
Seller shall have no warranty obligations to Buyer with respect to any product or parts of a
product that have been: (a) repaired by third parties other than Seller or without Seller’s
written approval; (b) subject to misuse, misapplication, neglect, alteration, accident, or
physical damage; (c) used in a manner contrary to Seller’s instructions for installation,
operation and maintenance; (d) damaged from ordinary wear and tear, corrosion, or
chemical attack; (e) damaged due to abnormal conditions, vibration, failure to properly
prime, or operation without flow; (f) damaged due to a defective power supply or
improper electrical protection; or (g) damaged resulting from the use of accessory
equipment not sold or approved by Seller. In any case of products not manufactured by
Seller, there is no warranty from Seller; however, Seller will extend to Buyer any warranty
received from Seller’s supplier of such products.
THE FOREGOING WARRANTY IS PROVIDED IN PLACE OF ALL OTHER EXPRESS
WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED TO ONE (1) YEAR FROM THE DATE OF INSTALLATION OR
EIGHTEEN (18) MONTHS FROM THE PRODUCT DATE CODE , WHICHEVER SHALL
OCCUR FIRST. EXCEPT AS OTHERWISE REQUIRED BY LAW, BUYER’S EXCLUSIVE
REMEDY AND SELLER’S AGGREGATE LIABILITY FOR BREACH OF ANY OF THE
FOREGOING WARRANTIES ARE LIMITED TO REPAIRING OR REPLACING THE PRODUCT
AND SHALL IN ALL CASES BE LIMITED TO THE AMOUNT PAID BY THE BUYER FOR THE
DEFECTIVE PRODUCT. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY OTHER FORM
OF DAMAGES, WHETHER DIRECT, INDIRECT, LIQUIDATED, INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, EXEMPLARY OR SPECIAL DAMAGES, INCLUDING BUT
NOT LIMITED TO LOSS OF PROFIT, LOSS OF ANTICIPATED SAVINGS OR REVENUE,
LOSS OF INCOME, LOSS OF BUSINESS, LOSS OF PRODUCTION, LOSS OF
OPPORTUNITY OR LOSS OF REPUTATION.
Some states do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which may
vary from state to state.
8 Product warranty
16 Sump and Effluent Pump INSTRUCTION MANUAL

To make a warranty claim, check first with the dealer from whom you purchased the
product or visit www.xyleminc.com for the name and location of the nearest dealer
providing warranty service.
8 Product warranty
Sump and Effluent Pump INSTRUCTION MANUAL 17

Xylem |’zīləm|
1) The tissue in plants that brings water upward from the roots
2) A leading global water technology company
We’re a global team unified in a common purpose: creating innovative solutions
to meet our world's water needs. Developing new technologies that will improve
the way water is used, conserved, and re-used in the future is central to our work.
We move, treat, analyze, and return water to the environment, and we help
people use water efficiently, in their homes, buildings, factories and farms. In
more than 150 countries, we have strong, long-standing relationships with
customers who know us for our powerful combination of leading product brands
and applications expertise, backed by a legacy of innovation.
For more information on how Xylem can help you, go to xyleminc.com
Xylem Inc.
1 Goulds Drive
Auburn - NY 13021
USA
Tel: [phone]
Fax: [phone]
www.gouldswatertechnology.com
Visit our Web site for the latest version of this document
and more information
The original instruction is in English. All non-English
instructions are translations of the original instruction.
©2016 Xylem Inc
GSP_REV 2 PRINTED IN CHINA