Xylem LOWARA LNTSE User manual

Smart Pump Range
Installation, Operation
and Maintenance Manual
Software Version 151.00
Cod.001080138EN rev.A ed.04/2017
LNEEE
LNTSE
LNESE LNTEE

en – Original instructions
2
Table of Contents
1 Introduction and safety .............................................................................................................................................5
1.1 Introduction........................................................................................................................................................5
1.1.1 Qualified personnel........................................................................................................................................5
1.2 Safety.................................................................................................................................................................5
1.2.1 Safety message levels...................................................................................................................................6
1.3 User safety.........................................................................................................................................................7
1.4 Inexperienced users ..........................................................................................................................................8
1.5 Protecting the environment ..............................................................................................................................8
1.6 Warranty ............................................................................................................................................................9
1.7 Spare parts ........................................................................................................................................................9
1.8 DECLARATION OF CONFORMITY..................................................................................................................9
1.8.1 EC Declaration of Conformity (Original) ........................................................................................................9
1.8.2 EU Declaration of Conformity (No EMCD24) ................................................................................................9
2 Storage and Transportation ................................................................................................................................... 11
2.1 Inspect the package ....................................................................................................................................... 11
2.2 Storage guidelines.......................................................................................................................................... 11
2.3 Inspect the unit ............................................................................................................................................... 11
2.4 Transportation guidelines .............................................................................................................................. 11
2.5 System lifting .................................................................................................................................................. 11
2.5.1 Lifting diagrams ......................................................................................................................................... 12
3 Product Description ............................................................................................................................................... 13
3.1 Product design................................................................................................................................................ 13
3.2 Applications .................................................................................................................................................... 14
3.2.1 Actuator (constant speed) .......................................................................................................................... 14
3.2.2 Controller (constant pressure) .................................................................................................................... 14
3.3 Data plates...................................................................................................................................................... 14
3.3.1 Motor........................................................................................................................................................... 14
3.3.2 Pump .......................................................................................................................................................... 15
3.4 Motor technical data ....................................................................................................................................... 17
3.5 Dimensions and weights ................................................................................................................................ 17
3.6 Design and layout........................................................................................................................................... 19
3.7 Pre-assembledexfactorycomponents .......................................................................................................... 20
3.8 Optional components ................................................................................................................................... 20
4 Mechanical Installation ........................................................................................................................................... 21
4.1 Installationsitechecklist ................................................................................................................................ 21
4.2 Unit installation ............................................................................................................................................... 21
4.3 Outdoor installation......................................................................................................................................... 22
5 Electrical Installation 23
5.1 Precautions..................................................................................................................................................... 23

en – Original instructions
3
5.2 Electricalrequirements .................................................................................................................................. 23
5.3 Wire type and ratings .................................................................................................................................... 24
5.4 Power supply connection ............................................................................................................................... 24
6 Operation ................................................................................................................................................................ 27
6.1 Discharge time ............................................................................................................................................... 27
7 Programming .......................................................................................................................................................... 28
7.1 Control panel .................................................................................................................................................. 28
7.2 Functions of push buttons .............................................................................................................................. 29
7.3 LEDs description ............................................................................................................................................ 29
7.3.1 Power LED (2) ............................................................................................................................................ 29
7.3.2 Status LED (5) ............................................................................................................................................ 29
7.3.3 Speed LED bar (4)...................................................................................................................................... 29
7.3.4 Communication LED (1) ............................................................................................................................. 30
7.3.5 Unit of measure LEDs (3) description ........................................................................................................ 30
7.4 Numeric display (6)......................................................................................................................................... 30
7.4.1 Main visualization ....................................................................................................................................... 30
7.4.2 Parameters menu visualization .................................................................................................................. 31
7.4.3 Alarms and errors visualization .................................................................................................................. 32
7.5 Software parameters ...................................................................................................................................... 32
7.5.1 Status Parameters...................................................................................................................................... 32
7.5.2 Settings Parameters ................................................................................................................................... 34
7.5.3 Drive Configuration Parameters ................................................................................................................. 34
7.5.4 Sensor Configuration Parameters .............................................................................................................. 35
7.5.5 RS485 Interface Parameters ...................................................................................................................... 35
7.5.6 Test Run Configuration Parameters ........................................................................................................... 36
7.5.7 Special Parameters .................................................................................................................................... 36
7.6 Fault finding .................................................................................................................................................... 36
7.6.1 Alarm codes................................................................................................................................................ 37
7.6.2 Error codes ................................................................................................................................................. 37
8 Maintenance ........................................................................................................................................................... 38
8.1 General ........................................................................................................................................................... 38
8.2 Check the functions and parameters.............................................................................................................. 38
9 Technical Reference .............................................................................................................................................. 39
9.1 Example: ACT control mode with analog 0-10V input ............................................................................... 39

en – Original instructions
5
1 Introduction and safety
1.1 Introduction
Purpose of this manual
The purpose of this manual is to provide necessary information for:
• Installation
• Operation
• Maintenance
CAUTION:
Read this manual carefully before installing and using the product. Improper use of the product
can cause personal injury and damage to property, and may void the warranty.
NOTICE:
Save this manual for future reference, and keep it readily available at the location of the unit.
1.1.1 Qualified personnel
WARNING:
This product is intended to be operated by qualified personnel only.
• Correct and reliable transport, storage, installation, operation, and maintenance are required
for the trouble-free and safe operation of the frequency converter. Only qualified personnel
are allowed to install or operate this equipment.
• Qualified personnel are defined as trained staff, who are authorized to install, commission,
and maintain equipment, systems, and circuits in accordance with pertinent laws and
regulations. Also, the personnel must be familiar with the instructions and safety measures
that are described in this document.
1.2 Safety
WARNING:
•
The operator must be aware of safety precautions to prevent physical injury.
• Unintended rotation of motors creates voltage and can charge the unit, resulting in death,
serious injury, or equipment damage. Ensure that motors are blocked to prevent unintended
rotation.
• Operating, installing, or maintaining the unit in any way that is not covered in this manual could
cause death, serious personal injury, or damage to the equipment. This includes any
modification to the equipment or use of parts not provided by Xylem. If there is a question
regarding the intended use of the equipment, please contact a Xylem representative before
proceeding.
• Do not change the service application without the approval of an authorized Xylem
representative.
CAUTION:
You must observe the instructions contained in this manual. Failure to do so could result in
physical injury, damage, or delays.

en – Original instructions
6
1.2.1 Safety message levels
About safety messages
It is extremely important that you read, understand, and follow the safety messages and
regulations carefully before handling the product. They are published to help prevent these
hazards:
• Personal accidents and health problems
• Damage to the product
• Product malfunction.
Definitions
Safety message level Indication
DANGER:
A hazardous situation which, if not avoided, will result in
death or serious injury
WARNING:
A hazardous situation which, if not avoided, could result
in death or serious injury
CAUTION:
A hazardous situation which, if not avoided, could result
in minor or moderate injury
Electrical Hazard:
The possibility of electrical risks if instructions are not
followed in a proper manner
NOTICE:
• A potential situation which, if not avoided, could
result in undesirable conditions
• A practice not related to personal injury
Hot surface hazard
Hot surface hazards are indicated by a specific symbol that replaces the typical hazard level
symbols:
CAUTION:
Magnetic hazard
WARNING:
A strong magnetic field is created when the rotor is removed from or inserted into the motor
housing. This magnetic field can be harmful to pacemaker wearers and others with medical
implants. In addition, the magnetic field may attract metal parts to the rotor which can cause
injuries and/or damage the bearings of the motor.
Description of user and installer symbols
Specific information for personnel in charge of installing the product in the system (plumbing or electrical
aspects, or both) or in charge of maintenance.

en – Original instructions
7
Specific information for users of the product.
1.3 User safety
General safety rules
These safety rules apply:
• Always keep the work area clean.
• Pay attention to the risks presented by gas and vapors in the work area.
• Avoid all electrical dangers. Pay attention to the risks of electric shock or arc flash hazards.
• Always bear in mind the risk of drowning, electrical accidents, and burn injuries.
Safety equipment
Use safety equipment according to the company regulations. Use this safety equipment within
the work area:
• Hard hat
• Safety goggles, preferably with side shields
• Protective shoes
• Protective gloves
• Gas mask
• Hearing protection
• First-aid kit
• Safety devices
NOTICE:
Never operate a unit unless safety devices are installed. Also see specific information about
safety devices in other chapters of this manual.
Electrical connections
Electrical connections must be made by certified electricians in compliance with all international,
national, state, and local regulations. For more information about requirements, see sections
dealing specifically with electrical connections.
Precautions before work
Observe these safety precautions before you work with the product or are in connection with the
product:
• Provide a suitable barrier around the work area, for example, a guard rail.
• Make sure that all safety guards are in place and secure.
• Make sure that you have a clear path of retreat.
• Make sure that the product cannot roll or fall over and injure people or damage property.
• Make sure that the lifting equipment is in good condition.
• Use a lifting harness, a safety line, and a breathing device as required.
• Allow all system and pump components to cool before you handle them.
• Make sure that the product has been thoroughly cleaned.
• Disconnect and lock out power before you service the pump.
• Check the explosion risk before you weld or use electric hand tools.
Precautions during work
Observe these safety precautions when you work with the product or are in connection with the
product:
• Never work alone.
• Always wear protective clothing and hand protection.
• Stay clear of suspended loads.
• Always lift the product by its lifting device.
• Beware of the risk of a sudden start if the product is used with an automatic level control.
• Beware of the starting jerk, which can be powerful.
• Rinse the components in water after you disassemble the pump.

en – Original instructions
8
• Do not exceed the maximum working pressure of the pump.
• Do not open any vent or drain valve or remove any plugs while the system is pressurized.
Make sure that the pump is isolated from the system and that pressure is relieved before you
disassemble the pump, remove plugs, or disconnect piping.
• Never operate a pump without a properly installed coupling guard.
Wash the skin and eyes
Follow these procedures for chemicals or hazardous fluids that have come into contact with your
eyes or your skin:
Condition Action
Chemicals or hazardous fluids
in eyes
1. Hold your eyelids apart forcibly with your fingers.
2.
Rinse the eyes with eyewash or running water for at least 15 min.
3.
Seek medical attention.
Chemicals or hazardous fluids
on skin
1. Remove contaminated clothing.
2.
Wash the skin with soap and water for at least 1 min.
3.
Seek medical attention, if necessary.
1.4 Inexperienced users
WARNING:
This product is intended to be operated by qualified personnel only.
Be aware of the following precautions:
• This product is not to be used by anyone with physical or mental disabilities, or anyone
without the relevant experience and knowledge, unless they have received instructions on
using the equipment and on the associated risks or are supervised by a responsible person.
• Children must be supervised to ensure that they do not play on or around the product.
1.5 Protecting the environment
Emissions and waste disposal
Observe the local regulations and codes regarding:
• Reporting of emissions to the appropriate authorities.
• Sorting, recycling and disposal of solid or liquid waste.
• Clean-up of spills.
Exceptional sites
CAUTION: Radiation Hazard
Do NOT send the product to Xylem if it has been exposed to nuclear radiation, unless Xylem has
been informed and appropriate actions have been agreed upon.
Recycling guidelines
Always follow local laws and regulations regarding recycling.
Waste and emissions guidelines
Do not dispose of equipment containing electrical components together with domestic
waste.
Collect it separately in accordance with local and currently valid legislation.

en – Original instructions
9
1.6 Warranty
For information about warranty, see the sales contract
1.7 Spare parts
WARNING:
Only use original spare parts to replace any worn or faulty components. The use of unsuitable
spare parts may cause malfunctions, damage, and injuries as well as void the guarantee.
For more information about the product's spare parts, refer to the Sales and Service department
1.8 DECLARATION OF CONFORMITY
1.8.1 EC Declaration of Conformity (Original)
Xylem Service Italia S.r.l., with headquarters in Via Vittorio Lombardi 14 - 36075 Montecchio
Maggiore VI - Italy, hereby declares that the product:
In-line electric pump unit with integrated variable speed drive, with or without pressure
transmitters (see label on first page)
fulfills the relevant provisions of the following European directives:
• Machinery 2006/42/EC (ANNEX II - natural or legal person authorised to compile the technical
file: Xylem Service Italia S.r.l.)
• Eco-design 2009/125/EC, Regulation (EU) No 547/2012 (Water pump) if MEI marked,
and the following technical standards:
• EN 809:1998+A1:2009, EN 60204-1:2006+A1:2009
• EN 50598-1:2014, EN 50598-2:2014
Montecchio Maggiore, 22/03/2017
Amedeo Valente
(Director of Engineering and R&D)
rev.01
1.8.2 EU Declaration of Conformity (No EMCD24)
1. Apparatus model/Product:
see label on first page
2. Name and address of the manufacturer:
Xylem Service Italia S.r.l.
Via Vittorio Lombardi 14
36075 Montecchio Maggiore VI
Italy
3. This declaration of conformity is issued under the sole responsibility of the manufacturer.
4. Object of the declaration:
In-line electric pump unit with integrated variable speed drive, with or without pressure
transmitters (see label on first page)
5. The object of the declaration described above is in conformity
with the relevant Union harmonisation legislation:
Directive 2014/30/EU of 26 February 2014
(electromagnetic compatibility)
6. References to the relevant harmonised standards
used or references to the other technical
specifications, in relation to which conformity is
declared:
EN 60730-1:2011, EN 61800-3:2004+A1:2012 (Category C2),
EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+A1:2001+
A2:2008, EN 61000-6-2:2005, EN 61000-6-3:2007+A1:2011
7. Notified body: -
8. Additional information:

en – Original instructions
10
Signed for and on behalf of: Xylem Service Italia S.r.l.
Montecchio Maggiore, 22/03/2017
Amedeo Valente
(Director of Engineering and R&D)
rev.01
Lowara is a trademark of Xylem Inc. or one of its subsidiaries.

en – Original instructions
11
2 Storage and Transportation
2.1 Inspect the package
1. Inspect the package for damaged or missing items upon delivery.
2. Note any damaged or missing items on the receipt and freight bill.
3. File a claim with the shipping company if anything is out of order.
4. If the product has been picked up at a distributor, make a claim directly to the distributor.
2.2 Storage guidelines
Storage location
The product must be stored in a covered and dry location free from heat, dirt, and vibrations.
NOTICE:
Protect the product against humidity, heat sources, and mechanical damage.
NOTICE:
Do not place heavy weights on the packed product.
NOTICE:
Refer also to par. 3.4 for storage limits.
2.3 Inspect the unit
1. Remove packing materials from the product.
2. Dispose of all packing materials in accordance with local regulations.
3. Inspect the product to determine if any parts have been damaged or are missing.
4. If applicable, unfasten the product by removing any screws, bolts, or straps. For your personal
safety, be careful when you handle nails and straps.
5. Contact the local sales representative if there is any issue.
2.4 Transportation guidelines
Precautions
WARNING:
•
Stay clear of suspended loads.
• Observe accident prevention regulations in force.
• Do not damage the cables during transport; do not squeeze, bend or drag the cable.
• Always keep the cable ends dry.
• Secure the unit against tipping over and slipping until it is mounted and fixed in its final
location.
• Lift and handle the product carefully, using suitable lifting equipment (stacker, crane, crane
mounting device, lifting blocks, sling ropes, etc.).
• Always lift the unit by its lifting handle.
2.5 System lifting
WARNING:
Assembled units and their components are heavy. Failure to properly lift and support this
equipment can result in serious physical injury and/or equipment damage. Lift equipment only at
the specifically identified lifting points. Lifting devices such as eyebolts, slings, and spreaders
must be rated, selected, and used for the entire load being lifted.

en – Original instructions
12
WARNING: Crush Hazard
1. Always lift the unit by its designated lifting points.
2. Use suitable lifting equipment and ensure that the product is properly harnessed.
3. Wear personal protective equipment.
4. Stay clear of cables and suspended loads.
2.5.1 Lifting diagrams
Figure 1: Lifting

en – Original instructions
13
3 Product Description
3.1 Product design
The product is a single stage in-line pump with:
• The water inlet on the same axis as the water outlet of the pump
• The suction and discharge nozzles with the same nominal diameter of the flange.
The pump is equipped with a single radial closed impeller and driven by a variable speed electric
motor.
The product can be used for handling:
• Cold or warm water
• Clean liquids
• Aggressive liquids which are not chemically and mechanically aggressive to the pump
materials.
Intended use
The product is suitable for:
• Water supply
• Cooling and hot water supply in industries and building services
• Filter systems
• Heating systems
• Condensate transportation.
Additional uses for optional material:
• District heating
• General industry
• Food and beverage industry.
Improper use
WARNING:
Improper use of the product may create dangerous conditions and cause personal injury and
damage to property.
An improper use of the product leads to the loss of the warranty.
Examples of improper use:
• Liquids not compatible with the product construction materials
• Hazardous liquids (such as toxic, explosive, flammable, or corrosive liquids)
• Potable liquids other than water (for example, wine or milk).
Examples of improper installation:
• Hazardous locations (such as explosive, or corrosive atmospheres)
• Location where the air temperature is very high or there is poor ventilation
• Outdoor installations where there is no protection against rain or freezing temperatures.
DANGER:
Do not use this product to handle flammable or explosive liquids, or both.
NOTICE:
•
Do not use this product to handle liquids containing abrasive, solid, or fibrous substances.
• Do not use the product for flow rates beyond the specified flow rates on the data plate.
Special applications
Contact the local sales and service representative in the following cases:

en – Original instructions
14
• If the density and/or viscosity value of the pumped liquid exceeds the value of water, such as
water with glycol; as it may require a more powerful motor.
• If the pumped liquid is chemically treated (for example softened, deionized, demineralized
etc.).
• Any situation that is different from the ones that is described and relate to the nature of the
liquid.
Approval and certifications
See motor nameplate for approvals:
• only
• + .
3.2 Applications
The application alternatives for the product are the following:
3.2.1 Actuator (constant speed)
The unit operates as an actuator according to speed set point; this is done through user
interface, the corresponding analog input or the communication bus.
3.2.2 Controller (constant pressure)
This mode is set as the default operating mode and is used for a unit in a single pump operation.
3.3 Data plates
3.3.1 Motor
Motor data plate
Figure 2: Motor data plate
1. Type definition code
2.
Rated voltage
3.
Rated frequency
4.
Rated power [kW]
5.
Rated power [HP]
6.
Part number
7.
Insulation class and protection degree
8.
Serial number
9.
Maximum ambient temperature
10.
Power factor
11.
Rated current
12.
Motor drive efficiency
13.
Full power speed range
14.
Code letter for locked rotor
15.
Duty type
16.
Enclosure type
17.
Weight
18.
Protection class
19.
Shaft power
20.
Voltage
21.
Current
22.
Part number
23.
Serial number
24.
Power factor
25.
Speed
26.
Power drive system efficiency class (according to EN
50598-2)
27.
Full load efficiency

en – Original instructions
15
Motor type definition code
Figure 3: Motor type definition code
1. Series ESM
2.
Motor frame
dimension
90R: Oversized Flange
80: Standard Flange
3.
Shaft extension □□: Standard shaextension
S8: Custom Shaft extension
4.
Power supply 1: single phase power supply
3: three phase power supply
5.
Shaft power•10 [kW] 03: 0.37 kW (0.50 HP)
05: 0.55 kW (0.75 HP)
07: 0.75 kW (1.00 HP)
11: 1.10 kW (1.50 HP)
15: 1.50 kW (2.00 HP)
22: 2.20 kW (3.00 HP)
6.
Motor frame
arrangement
SVE: Flange with tapped holes and shaft w/o keyseat
B14: Flange with tapped holes
B5: Flange with free holes
HMHA: Suitable for 1÷5 e-HM monolithic pumps
HMHB: Suitable for 1÷5 e-HM w/sleeve pumps
HMVB: Suitable for 1÷5 e-VM pumps
HMHC: Suitable for 10÷22 e-HM pumps
HMVC: Suitable for 10÷22 e-VM pumps
LNEE: Suitable for In-Line pumps
56J: Compliant to NEMA 56 Jet standard
56C: Compliant to NEMA 56C standard
7.
Reference market □□: Standard
EU: EMEA
US: North America
8.
Voltage 208-240 : 208-240 VAC 50/60 Hz
380-460 : 380-460 VAC 50/60 Hz
230/400: 208-240/380-460 VAC 50/60 Hz
3.3.2 Pump
e-LNEEE/e-LNESE/e-LNTSE data plate
Figure 4: e-LNEEE/e-LNESE/e-LNTSE data plate

en – Original instructions
16
1. Electropump unit type
2.
Serial number (date+progressive number)
3.
Capacity range
4.
Minimum head (EN 60335-2-41)
5.
Maximum operating pressure
6.
Rated voltage range
7.
Frequency
8.
Minimum efficiency index
9.
Electropump unit part number
10.
Hydraulic efficiency in best efficiency point
11.
Head range
12.
Motor nominal power
13.
Maximum operating liquid temperature
14.
Protection class
15.
Current
16.
Electropump unit absorbed power
17.
Trimmed impeller diameter (only filled in for trimmed
impellers)
18.
Full impeller diameter (only filled in for trimmed
impellers)
e-LNEEE/e-LNESE/e-LNTSE type definition code
Figure 5: e-LNEEE/e-LNESE/e-LNTSE type definition code
1. Pump type [LNE] = In-line single
[LNT] = In-line twin
2.
Coupling [E] = Extended shaft
[S] = Stub shaft
3.
Motor operation [E] = e-SM
4.
Size of the pump Discharge diameter – nominal impeller diameter
5.
Motor power kW x 10
6.
Special trimmed
impeller
[A or B] = Trimmed medium diameter that doesn’t maximize motor power
[X] = Trimmed medium diameter to meet customer required duty point
7.
Motor type [/E] = e-SM
8.
Number of poles [P] = e-SM
9.
Electrical voltage +
frequency
[02] = 1x208-240 V
[04] = 3x380-460 V
[05] = 3x208-240/380-460 V
10.
Casing material [C] = Cast iron
11.
Impeller material [C] = Cast iron
[S] = Fabricated stainless steel
[B] = Bronze
[N] = Cast stainless steel (1.4408)
[R] = Duplex (1.4517)
12.
Mechanical seal + O-
ring configuration
[4] = SiC/Carbon/EPDM
[2] = SiC/Carbon/FKM
[Z] = SiC/SiC/EPDM
[W] = SiC/SiC/FKM
[L..] = Tungsten Carbide/Metal-impregnated Carbon/EPDM
[U..] = Tungsten Carbide/Metal-impregnated Carbon/FKM

en – Original instructions
17
3.4 Motor technical data
Table 1: Electrical, Environmetal and Installation specifications
e-SM Drive model
103 105 107 111 115 303 305 307 311 315 322
Input
Input frequency [Hz] 50/60 ± 2
Mains supply LN L1 L2 L3
Nominal input voltage [V] 208÷240 ±10% 208÷240 / 380÷460 ±10%
380÷
460
±10%
Max. Input Current Continuous
[A]
2,3 3,3 4,4 6,3 8,6 - - - - - -
PDS Efficiency Class IES2
Output
Min.÷Max. Speed [rpm] 800÷3600
Leakage Current [mA] < 3,5
I/O auxiliar + 15VDC power
supply [mA]
Imax < 40
Fault signal relay 1 x NO Vmax < 250 [VAC]
Imax < 2 [A]
2 x NO Vmax < 250 [VAC]
Imax < 2 [A]
EMC (Electro Magnetic
Compatibility)
See par.1.8 DECLARATION OF CONFORMITY.
Installations must be done according to EMC good practice guidelines
(e.g. avoiding pigtails on drive side)
Sound Pressure LpA
[dB(A) @rpm]
<62 @3000
<66 @3600
Insulation class 155 F
Enclosure Rate IP 55, Enclosure Type 1
Protect the product from direct sunlight and rainfall
Relative humidity RH (storage
& operating)
5% ÷ 95%
Storage temperature [°C (°F)] -25÷65(-13÷149)
Operating temperature [°C (°F)] -20÷50 (-4÷122)
Air Pollution Degree 2
Altitude [m (ft)] Max. 1000 (3280) above sea level.
For installation over 1000 (3280) above sea level de-rating may occur
3.5 Dimensions and weights
Reading instructions
Drawings show dimensions only in mm.
The images are not to scale.

en – Original instructions
18
Figure 6: Dimensions
Table 2: Dimensions and weights
Model
Net weight (motor + drive)
[kg]
B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 D1 D2 D3 E1 E2
30 (900W) 60 (1700W) [mm]
90R...LNEE 7.4 8.9 376
224 149
-79
70 224 80 117 23 68 74 M16 M12
M20
--
90RS8....LNEE 7.3 8.8 343 - 79 - -
90R...B14-SVE 7.5 9 292 - 79 - -
90R...B5 7.5 9 292 - 100 - -
80...HMHA
80...HMHA US
80...HMHA EU
7.5 9 263 90 79 100 125
80...HMHB
80...HMHB US
80...HMHB EU
7.6 9.2 268 90 80 100 125
80...HMVB
80...HMVB US
80...HMVB EU
7.4 8.9 268 - 80 - -
80...HMHC
80...HMHC US
80...HMHC EU
7.9 9.4 272 90 91 100 125
80...HMVC
80...HMVC US
80...HMVC EU
7.6 9.1 272 - 91 - -
80...BG 7.3 8.8 282 - 108 - -
90R...56J 7.5 9.1 307 89 83 NPT
1/2"
76 124
90R...56C 7.2 8.8 294 - 83 - -
… = 103, 105, 107, 111, 115
Blank cell = motor foot is missing
Minimum spacing
Table 3: Minimum spacing
Area e-SM Drive model Minimum spacing [mm (in)]
Above the unit 103..105..107..111..115 >260 (10.2)
Minimum spacing or center-distance between
units
103..105..107..111..115 >260 (10.2)
303..305..307..311..315..322 ≥300 (11.8)

en – Original instructions
19
3.6 Design and layout
Parts and descriptions
The unit can be fitted with the features the application requires.
Figure 7: Open terminal box cover on drive models 103, 105, 107, 111, 115
Table 4: Part description
Position
number
Description Tightening torque
[Nm (lbf·in)]
1 Captive Screws 1.2 (11)
2 Terminal Box Cover -
3 Optional module with strip -
4 IO Cable gland M12 (3x) / M16 (1x) 0.7/2 (6.4/18.3)
5 M20 Power cable gland 2.7 (24.75)

en – Original instructions
20
3.7 Pre-assembled ex factory components
Table 5: Included components
Included components Cable Outer Diameter
[mm (in)]
e-SM Drive model
103, 105, 107,
111, 115
303, 305, 307,
311, 315, 322
Cable Gland(s) and Lock
Nut(s)
M12 3.7÷7.0 (0.145÷0.275) 3 3
M16 4.5÷10.0 (0.177÷0.394) 1 1
Cable Gland M20 7.0÷13.0 (0.275÷0.512) 1 1
Plug(s) for Cable
Gland(s)
M12 included 3 3
M16 included 1 1
M20 included 1 1
3.8 Optional components
Table 6: Optional components
Component Description
Sensors The following sensors can be used with the unit:
• Differential pressure-transducer
RS485 Module To connect and interact by wire with e-SM Drive
Wireless Module To connect and interact wireless with e-SM Drive
Adaptor M20 Metric to 1/2" NPT Adapter (item is always
supplied for US market)