Yamaha CLAVINOVA CLP-635 Mounting instructions

CLP-635, CLP-645, CLP-665GP,
CLP-675, CLP-685, CLP-695GP,
YDP-184
Firmware Update Guide
 Preparingtoupdatethefirmware
1. PrepareaUSBflashdrivewithenoughfreespace.
2. Usethelistbelowtofindthefirmwarefileforyourinstrument,andthencopyitto
therootoftheUSBflashdrivefilesystem.
ProductFirmwareFileName
CLP‐635CLP‐635SETUP.PRG
CLP‐645CLP‐645SETUP.PRG
CLP‐665GPCLP‐665GPSETUP.PRG
CLP‐675CLP‐675SETUP.PRG
CLP‐685CLP‐685SETUP.PRG
CLP‐695GPCLP‐695GPSETUP.PRG
YDP‐184YDP‐184SETUP.PRG

UpdatingtheFirmware
Notice: The following must be observed during the firmware update
Do not turn off the instrument during the update.
Do not remove the USB flash drive from the instrument.
When you run into a trouble during the firmware update, refer to the Troubleshooting
section located at the end of this document.
1. Makesurethattheinstrumentisturnedoffbeforeupdatingthefirmware.
2. InserttheUSBflashdrivewiththecopiedfirmwareintotheUSB [TO DEVICE]terminal.
3. Pressandholdthe[▶/ll](PLAY/PAUSE)button,andturnontheinstrument.
Keepthe[▶/ll]buttonhelddownuntilthedisplayshowsthefollowingmessage.

Theredmarkingbelowshowswherethe[▶/ll]buttonislocatedonthepanel.
4. Pressthe[▶/ll]buttonagainwhenthedisplayshowsthefollowingmessage.

5. Pressthe[▶/ll]buttonyetagaintoexecutetheinstallationwhenthedisplayshows
thefollowingmessage.
Thefirmwareupdateinstallationstarts.Thedisplayshowstheinstallationprogress.
Notethattheinstallationmaytakearound10minutesforbigfirmwaredata.
Thedisplayshowstheinstalledversionwhentheupdatecompletes.
6. Turnofftheinstrument.YoucanremovetheUSBflashdrive.
7. Pressandholdtherightmostkey(C7),andturnontheinstrument.
Notice: This operation resets the instrument to its factor default settings.
Note that the Backup Setting will be reset to default.
(This operation will not delete the User MIDI Songs)
Thefirmwareupdateisnowcomplete.

Howtoconfirmtheinstalledfirmwareversion
1. Turnontheinstrument.
2. Pressthe[FUNCTION]buttonseveraltimestoselect“System”menu.
3. Press[∨]buttonseveraltimestoselect“Utility”,andthenpress[＞]button.
→
4. Press[∨]buttonseveraltimestoselect“Version”,andthenpress[＞]button.
→
5. Checkthedisplayedversionnumber.

Troubleshooting
1. ThepowerwasturnedoffortheUSBflashdrivewasremovedduringthefirmware
update.
→ Youneedtoperformalltheoperationsonceagain.Gobacktothefirststep,and
followallthestepstothefinish.
2. Anerrormessageisdisplayedandtheinstallationaborts.
→ Followthelistbelowtocheckif:
TheUSBflashdriveinsertedcorrectly?
NodustordirtisontheUSBterminal?
ThefirmwaredataisplacedintherootoftheUSBflashdrivefilesystem?
TheUSBflashdrivedataiscorrupt,ortheUSBflashdriveitselfisbroken?
Thefirmwaredataisthecorrectoneforyourinstrument?
UsinganotherUSBflashdriveresultsinthesameerror?
