Yamaha Silent guitar slg-100n User manual

20011220-62000

SERVICE MANUAL

EG 011620 HAMAMATSU, JAPAN

CONTENTS

SPECIFICATIONS ................................................. 3

PANEL LAYOUT ...................................... 4

CIRCUIT BOARD LAYOUT ................. 6

DISASSEMBLY PROCEDURE .............................. 7

LSI PIN DESCRIPTION .............................. 10

IC BLOCK DIAGRAM .................................... 10

CIRCUIT BOARDS ........................................ 11

INSPECTIONS ............................................................ 12

TUNING ...................................................................... 13

OVERALL CIRCUIT DIAGRAM ........................... 14

PARTS LIST

SLG-100N

This document is printed on chlorine free (ECF) paper with soy ink.

Guitar

1.018K-916 Printed in Japan ’02.01

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

IMPOR TANT NOTICE

This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed

that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under-

stood by the users, and have therefore not been restated.

WARNING : Failure to follow appropriate service and safety procedures when servicing this product may result in per-

sonal injury, destruction of expensive components and failure of the product to perform as specified. For

these reasons, we advise all Yamaha product owners that all service required should be performed by an

authorized Yamaha Retailer or the appointed service representative.

IMPORTANT : This presentation or sale of this manual to any individual or firm does not constitute authorization certifi-

cation, recognition of any applicable technical capabilities, or establish a principal-agent relationship of

any form.

The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and

service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable

and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to

exist, please contact the distributor’s Service Division.

WARNING : Static discharges can destroy expensive components. Discharge any static electricity your body may have

accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to

this bus.)

IMPORTANT : Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power

to the unit.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where

applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly

other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT

SO EVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose

eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling

food.

WARNING

Components having special characteristics are marked and must be replaced with parts having specification equal to those

originally installed.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

SPECIFICATIONS

Neck Mahogany

Body Maple

Fingerboard Rosewood

Bridge Rosewood

Frame Unit Maple

Strings Nylon Guitar Strings

Sensors B-BAND

Connectors/Controls • AUX IN

• AUX IN Level Control

• LINE OUT jack (monaural)

• PHONES jack (stereo)

• Volume

• BASS control

• TREBLE control

• REVERB switch (OFF/1/2)

• PHONES switch (ON/OFF)

• LINE OUT Jack with POWER Switch (In-

serting a plug into the jack switches the

power on)

Power Supply • AC Adaptor/6F22 (S-006P) battery x1 dual

power source

* Recommended AC Adaptors:PA-D09, PA-

1E, PA-3B

Battery Life Continuous Use

• Using Manganese battery :

approximately 13.5 hours

• Using Alkaline battery :

approximately 24 hours

With the reverb activated

• Using Manganese battery :

approximately 2 hours

• Using Alkaline battery :

approximately 7.5 hours

Input/Output Specifications

Input Level

• AUX IN: -40 dBm/1kHz sine wave

(REVERB OFF)

Output Level

• LINE OUT:-27 dBm/10k Ω

• PHONES (L/R): -31 dBm/39 Ω

Power Consumption Using AC adaptor (PA-D09)

• REVERB OFF: 1.9 W

1- 2 : 2.4 W

Using battery

• REVERB OFF: 0.2 W

1- 2 : 0.6 W

String Length 650 mm (25-9/16”)

Dimensions 965 (L) x 365 (W) x 80 (H) mm

38” (L) x 14-3/8” (W) x 3-1/8” (H)

(with the left frame attached and to the end

of the strap pin)

Weight approximately 1.8 kg (3 lbs. 15 oz.)

Accessories AC adaptor (PA-D09),

* May not be in your area.

Stereo earphones, Soft case

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

THISDEVICE COMPLIES WITH PART 15 OFTHE FCC

RULES. OPERATIONIS SUBJECT TO THE FOLLOWING

TWOCONDEITIONS: (1) THIS DEVICE MAYNOT CAUSE

HARMFULINTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPTANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCETHAT MAYCAUSE UNDESIRED

OPERATION.

¥THIS CLASS B DIGITAL APPARATUSCOMPLIES WITH

CANADIANICES-003.

¥CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST

CONFORME¸ LA NORME NMB-003 DU CANADA.

ACPOWER ADAPTOR :

YAMAHAPA-1EOR PA-3B OR PA-D09

BATTERY: 9V 6LR61 OR 6F22YBATTERY: 9V 6LR61 OR 6F22Y

MADEIN TAIWAN

SILENTGUITAR

MODELSLG-100N

OPEN

LINE OUT AUX IN

AUX VOL

MIN MAX

EMC

N89

Front Rear

Neck

Saddle

Tuning peg

Body

Pickup (underneath the saddle)

Controls → See page 5.

Frame Attachment Screw 1 (Doubles as the Strap Pin)

Left Frame (Removable) Right Frame (Fixed)

Bridge

Horn (Leg Support)

Frame Attachment Screw 2 (Doubles as the Strap Pin)

Nut

Fingerboard

PANEL LAYOUT

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

Controls

OFF 1 2 OFF ON

PHONES

REVERB VOLUME BASS TREBLE

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC

RULES. OPERATION IS SUBJECTTO THE FOLLOWING

TWO CONDEITIONS: (1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

¥ THIS CLASS B DIGITAL APPARATUS COMPLIES WITH

CANADIAN ICES-003.

¥ CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST

CONFORME ¸ LA NORME NMB-003 DU CANADA.

AC POWER ADAPTOR :

YAMAHA PA-1E OR PA-3B OR PA-D09

BATTERY : 9V 6LR61 OR 6F22YBATTERY : 9V 6LR61 OR 6F22Y

MADE IN TAIWAN

SILENT GUITAR

MODEL SLG-100N

OPEN

LINE OUT

AUX IN

AUX VOL

MIN MAX

EMC

N89

VOLUME control

6F22 (S-006P) 9V battery

REVERB switch

POWER lamp

AUX IN jack

AUX IN level control

Cord hook

LINE OUT jack

DC-IN jack

(Power adaptor connector) BASS control

TREBLE control

PHONES ON/OFF switch

PHONES jack

DC-IN 9~12V

+–

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

CIRCUIT BOARD LAYOUT

AUX

PUP

Jack

Panel Assembly

Body (rear view)

(underneath the panel assembly)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

DISASSEMBLY PROCEDURE

Preparations

Make the following preparations;

Turn off the power switch.

Remove the battery cover and battery.

1. Left Frame (Time required: About 2 minutes)

1-1 Loosen the adjusting bolt (front) marked [E15] and the adjusting

bolt (rear) marked [E16]. The left frame can then be removed.

(Fig.1)

2. Bracket Assembly, Bracket, Sleeve

(Time required: About 5 minutes each)

2-1 Remove the left frame. (See procedure 1.)

2-2 Bracket Assembly:

Remove the two (2) screws marked [D05]. The upper bracket

assembly can then be removed from the left frame. (Fig.1)

The lower bracket assembly can be removed in the same manner.

2-3 Bracket, Sleeve:

Remove the two (2) screws marked [E19]. The upper bracket

and the upper sleeve can then be removed. (Fig.1)

The lower bracket and the lower sleeve can be removed in the

same manner.

3. Right Frame (Time required: About 2 minutes)

3-1 Remove the four (4) screws marked [E22]. The right frame can

then be removed with the horn. (Fig.1)

4. Horn, Right Bracket (Time required: About 5 minutes each)

4-1 Remove the right frame. (See procedure 3.)

4-2 Horn:

Remove the two (2) screws marked [D08]. The horn can then be

removed. (Fig.1)

4-3 Right Bracket:

Remove the two (2) screws marked [E21]. The upper right

bracket can then be removed. (Fig.1)

The lower right bracket can be removed in the same manner.

Peg Peg

String

Bracket assembly

Right bracket

Right frame

Pickup

Panel holder assembly

Panel holder

Spacer

Horn

Right bracket

Bracket

Sleeve

Left frame

[E19]

[D05]

Sleeve

[E19]

[E16]

[D05]

[

E22

]

[E21]

[D08]

[E21]

[E22]

[F02] X 4

[E15]

PUP

[D05]: Flat HeadTapping Screw-2

3.0X8 (QC667000)

[D08]: Flat HeadTapping Screw

3.5X20 (QC667100)

[E15]: Adjusting Bolt, Front

M6.0XP1X25 (QC653400)

[E16]: Adjusting Bolt, Rear

M6.0XP1X12 (QC653500)

[E19]: Flat HeadTapping Screw

3.0X14 ZMC2BL (QC699200)

[E21]: Flat HeadTapping Screw

3.0X14 ZMC2BL (QC699200)

[E22]: Flat HeadTapping Screw-2

3.0X8 (QC667000)

[F02]: Bind Head Tapping Screw-1

3.0X10 ZMC2BL (20404200)

Fig.1

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

5. Peg (Time required: About 5 minutes)

5-1 Remove the three (3) strings in left side (4th-6th strings) and right

side (1st-3rd strings) each. (Fig.2)

5-2 Remove the four (4) screws marked [E03] in left and right each.

The left and right pegs can then be removed. (Fig.2)

Fig.2

[E03]

Peg

Left side Strings (4

-6

)Right side Strings (1

-3

)

[E03]: Round Head Wood Screw 2.1X8 (03714060)

6. Panel Assembly (Time required: About 2 minutes)

6-1 Remove the four (4) screws marked [F05] and the four (4) screws

marked [F06]. The panel assembly can then be removed. (Fig.3)

7. MA Circuit Board, AUX Circuit Board,

Jack (LINE Connector Assembly)

(Time required: About 5 minutes each)

7-1 Remove the panel assembly. (See procedure 6.)

7-2 MA Circuit Board:

Pull out the three (3) rotary knobs for [VOLUME], [BASS] and

[TREBLE]. (Fig.3, 4)

Remove the two (2) screws marked [16A]. The MAcircuit board

can then be removed. (Fig.4)

7-3 AUX Circuit Board:

Pull out the AUX knob and remove the screw marked [16B].

TheAUX circuit board can then be removed with the jack holder.

(Fig.3, 4, 5)

Remove the hexagonal nut marked [A]. The jack holder can then

be removed from the AUX circuit board. (Fig.5)

7-4 Jack (LINE Connector Assembly):

Remove the hexagonal nut marked [10]. The jack (LINE

connector assembly) can then be removed. (Fig.3, 4)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

[VOLUME]

[BASS][TREBLE]

[F05] [F06]

[16B]

[10]

Rotary knob

[F05]

Jack (LINE connector assembly)

AUX knob

Jack (LINE connector assembly)

Rotary knob

[VOLUME]

[BASS][TREBLE]

[16A]

AUX

Fig.4

[F05]: Bind Head Tapping Screw-1 3.0X10 ZMC2BL (20404200)

[F06]: Bind Head Tapping Screw-B 3.0X10 ZMC2BL (EP600140)

[10]: Hexagonal Nut (AA820860)

[16B]: Bind Head Tapping Screw-B 3.0X10 ZMC2BL (EP600140)

Fig.3

[16A]: Bind Head Tapping Screw-B 3.0X10 ZMC2BL (EP600140)

Fig.5

[A]: Hexagonal Nut

Photo.1

Bridge saddle

Bridge

PickupPickup

String

[A]

Jack holder

AUX

8. PUP Circuit Board (Time required: About 5 minutes)

8-1 Remove the panel assembly. (See procedure 6.)

8-2 Remove the four (4) screws marked [F02]. The panel holder

assembly can then be removed. (Fig.1)

8-3 Remove the PUP circuit board from the two (2) spacers. (Fig.1)

9. Pickup (Time required: About 5 minutes)

9-1 Remove the panel assembly. (See procedure 6.)

9-2 Turn each pegs and loosen the strings. (Fig.1, Photo.1)

9-3 Remove the bridge saddle. (Photo.1)

9-4 Remove the pickup from the slot on the bridge. (Photo.1)

9-5 Disconnect the connector from the PUP circuit board. (Fig.1)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

LSI PIN DESCRIPTION

1 MD4 I/O 33 AVDD - DC A+5Vs bus

2 MD3 I/O 34 VDD - DC D+5V

3 MD0 I/O External RAM interface data 35 TST0 - DC D+5V

4 MD1 I/O 36 TST1 - DC D+5V

5 MD2 I/O 37 DOEN - DC D+5V

6 MCKO O Master clock output 38 SDO1 O N.C.

7 XO O Crystal oscillator connection 39 SDO0 O N.C.

8 XI I Crystal oscillator connection 40 WC O N.C.

9 ER0 I 41 BCO O N.C

10 ER1 I Eary refrection preset select 42 MA0 O

11 ER2 I 43 MA1 O

12 REV0 I 44 MA2 O

13 REV1 I Effect select 45 MA3 O

14 REV2 I 46 MA4 O

15 MUTEN I DC D+5V 47 MA5 O External RAM interface address

16 ICN I Initial clear 48 MA6 O

17 PRG I DC D+5V 49 MA7 O

18 MODE I Preset mode (H=DC +5V) 50 MA12 O

19 VSS - Ground 51 MA14 O

20 AVSS - Ground 52 VSS - Ground

21 CVA - N.C. 53 MA10 O

22 AORL O N.C. 54 MA011 O

23 AORR O N.C. 55 MA09 O External RAM interface address

24 CHL I Sample hold capacitor connection 56 MA8 O

25 AIL I Lch ADC input 57 MA13 O

26 VDD - DC D+5V 58 VDD - DC D+5V

27 AIR I Rch ADC input 59 WEN I Write enable

28 CHR I Sample hold capacitor connection 60 OEN I Output enable

29 AOFL O Lch DAC output 61 CEN I Chip select

30 AOFR O Rch DAC output 62 MD7 I/O

31 AVDD - DC A+5V 63 MD6 I/O External RAM interface data

32 CVB I Rch midpoint voltage 64 MD5 I/O

PIN NAME I/O FUNCTION

NO. PIN NAME I/O FUNCTION

NO.











YSS234



















































MA: IC01

DSP

(XN299A00) (Digital Sound Processor)

IC BLOCK DIAGRAM

NJM3404AM (XM527A00)

Dual Operational Amplifier

MA: IC08-13

PUP: IC15

NJM3414AM (XR294A00)

Dual Operational Amplifier

MA: IC14

4-V

Output A

Non-Inverting

Input A

-DC Voltage Supply

+DC Voltage

Supply

Output B

Inverting

Input B

Non-Inverting

Input B

Inverting

Input A

4-V

Output A

Non-Inverting

Input A

Ground

+DC Voltage

Supply

Output B

Inverting

Input B

Non-Inverting

Input B

Inverting

Input A

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

CIRCUIT BOARDS

REVERB

OFF/1/2

VOLUME

POWER Lamp

BASS TREBLE

ON/OFF

to Battery

terminal

to LINE OUT

Jack

DC-IN 9~12V

AUX IN

AUX VOL

MIN/MAX

PHONES

to Picku

(

B-BAND

)

MA Circuit Board

PUP Circuit Board AUX Circuit Board

Component side Pattern side

Component side Pattern side Component side Pattern side

Note: See parts list for details of circuit board component parts.

ENA-V872950-1, 2 0

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

INSPECTIONS

1. Required Equipment

High-sensitivity AC voltmeter (level meter)

Battery (006P) or power adapter (PA-D09)

2. Noise Level Measurement

Load resistance

[PHONES] jack: 39Ω(right and left each)

[LINE OUT] jack:10kΩ

(1) Turn on the power to the main unit, turn on the [PHONES]

switch, and check that the power LED (green) lights up.

(2) Connect the level meter to the [PHONES] jack.

(3) Turn the [VOLUME], [BASS] and [TREBLE] control dials to

the right most position (MAX).

(4) Stop the strings vibrating, measure the noise level, and check

that the noise levels for both right and left channels are –60dBm

or less.

(5) Disconnect the level meter from the [PHONES] jack and connect

it to the [LINE OUT] jack instead.

(6) Stop the strings vibrating, measure the noise level, and check

that the noise level is –60dBm or less.

3. Reverberation Inspection

(1) Connect a headphone to the [PHONES] jack.

(2) Pluck a string, switch the [REVERB] switch from “OFF” to “1”

and then to “2”, and check that the following effect is present at

both right and left headphone outputs.

REVERB Mode (reverberating time)

1 HALL (1.0 sec)

2 HALL (3.0 sec)

(3) Turn the [VOLUME] control dial to the left most position (MIN).

(4) Disconnect the headphone from the [PHONES] jack.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

Use a tuning meter, pitch pipe, tuning fork, piano, etc.,

and to the open strings to the pitches shown below.

• If the string’s pitch is high, loosen the string until the string’s

pitch is slightly lower than the tuning pitch, then tune while

raising the string’s pitch.

Play the standard pitch “lah” (A3: 440Hz) on a tuning fork,

etc., and tune the open 5th string to the same pitch.

Play the pitch produced by pressing the 5th string at the 5th

fret, and tune the open 4th string to the same pitch.

Play the pitch produced by pressing the 4th string at the 5th

fret, and tune the open 3rd string to the same pitch.

Play the pitch produced by pressing the 3rd string at the 4th

fret, and tune the open 2nd string to the same pitch.

Play the pitch produced by pressing the 2nd string at the 5th

fret, and tune the open 1st string to the same pitch.

Play the pitch produced by pressing the 6th string at the 5th

fret, and tune the pitch at the 5th fret of the 6th string to the pitch

produced by the open 5th string.

Open 1

String's Pitch: E

Open 2

String's Pitch: B

Open 3

String's Pitch: G

Open 4

String's Pitch: D

Open 5

String's Pitch: A

Open 6

Strin

's Pitch: E

1F 2F 3F 4F 5F

Open 1

String's Pitch: E

Open 2

String's Pitch: B

Open 3

String's Pitch: G

Open 4

String's Pitch: D

Open 5

String's Pitch: A

Open 6

String's Pitch: E

TUNING

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

PUP

AUX

CN5

RE-H022SD-1190

OP AMP

SYSTEM RESET

DSP

SRAM 256K

OP AMP

22K

VOLUME

PHONES

AUX VOL

DC-IN 9~12V

REVERB OFF/1/2

OP AMP

REGULATOR +8V

REGULATOR +5V

SYSTEM RESET

OP AMP

3.3K

1K1K 0.012u

TREBLE

BASS

TONE CONTROL

Note

Note: D7 is not installed.

to Pickup (B-BAND)

NJM78L08UA(XN00A00)

REGULATOR +8V

1: OUTPUT

2: COMMON

3: INPUT

123

NJU7202U50(X0150A00)

REGULATOR +5V

1: COMMON

2: INPUT

3: OUTPUT

123

: Mylar Capacitor

Note : See parts list for details of circuit board component parts.

STE-GA00P-04 2

LINE OUT

AUX IN

BATTERY

(+9V)

Power Lamp

TO SERVICE PERSONNEL

Critical Components Information

Components having special characteristics are marked

and must be replaced with parts having specifications

equal to those originally installed.

+–

OVERALL CIRCUIT DIAGRAM

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

PARTS LIST

WARNING

Components having special characteristics are marked and must be replaced with parts having

specification equal to those originally installed.

Notes : DESTINATION ABBREVIATIONS

The numbers “QTY” show quantities for each unit.

The parts with “--” in “PART NO.” are not available as spare parts.

This mark “ } ” in the REMARKS column means these parts are interchangeable.

The second letter of the shaded ( ) part number is O, not zero.

The second letter of the shaded ( ) part number is I, not one.

M: South African model

O: Chinese model

Q: South-east Asia model

T : Taiwan model

U : U.S.A. model

V : General export model (110V)

W: General export model (220V)

N,X: General export model

Y : Export model

A : Australian model

B : British model

C : Canadian model

D : German model

E : European model

F : French model

H : North European model

I : Indonesian model

J : Japanese model

CONTENTS

OVERALL ASSEMBLY .............................................. 2

PANEL ASSEMBLY ......................................... 4

ELECTRICAL PARTS ............................................. 6

SLG-100N

Guitar

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

OVERALL ASSEMBLY

F05

F06

F04

F02

F03

F09 F07

F08

E21

E20

E22

E16

E22

E15

A01

D07

D06

D08

E05

E08

E06

E07

D02

D01

E03

E03 E01

E04

E01

D05

D04

E14

E13 E12

E11 E10 E09

D03

E19 E17 E18

F01

F01a

F01b

F01e

F01c

F01d

Panel assembly:See page 4.

Panel holder assembly

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

REF NO.

PART NO. DESCRIPTION REMARKS

QTY

: New Parts RANK: Japan only

OVERALL ASSEMBLY SLG-100N

A01 Body

D01 Nut S M6.0XP1 L=13 #0186130

D02 Nut S M6.0XP1 L=10 #0186100

D03 Left Frame

D04 Bracket Assembly 2

D05 Flat Head Tapping Screw-2 3.0X8(Black Chrome) 4

D06 Right Frame

D07 Horn Maple

D08 Flat Head Tapping Screw 3.5X20(Black Chrom) 2

E01 Tuning Machine Assembly Pingway RM-1388 (Gold) 1set

E03 Round Head Wood Screw 2.1X8 (Brass) 801

E04 Nut Urea 50mm (White)

E05 Bridge Indian Rosewood

E06 Oval Head Wood Screw 2.4X16 (Chrome) 201

E07 Cap M5.0 (White) 201

E08 Bridge Saddle Urea 82mm (White)

E09 String 1 CG S11 (QA33300)

E10 String 2 CG S12 (QA33310)

E11 String 3 CG S13 (QA33320)

E12 String 4 CG S14 (QA25310)

E13 String 5 CG S15 (QA25320)

E14 String 6 CG S16 (QA25330)

E15 Adjusting Bolt, Front M6.0XP1X25 (Black)

E16 Adjusting Bolt, Rear M6.0XP1X12 (Black)

E17 Bracket (Black) 2

E18 Sleeve (Blue) 2

E19 Flat Head Tapping Screw 3.0X14 ZMC2BL (Black) 4

E20 Right Bracket (Black) 2

E21 Flat Head Tapping Screw 3.0X14 ZMC2BL (Black) 4

E22 Flat Head Tapping Screw-2 3.0X8(Black Chrome) 4

F01 Panel Holder Assembly (QC66260)

F01a Panel Holder

F01b Circuit Board PUP

F01c Spacer ACBS-2 (PINGOOD) 2

F01d Sponge 8X8 t=7 (QC68960) 2

F01e Connector Assembly PUP PHR-5P L=70 (QC66180)

F02 Bind Head Tapping Screw-1 3.0X10 ZMC2BL (Black) 4

F03 Aluminum Sheet (QC66250)

F04 Panel Assembly (QC66720)

F05 Bind Head Tapping Screw-1 3.0X10 ZMC2BL (Black) 4

F06 Bind Head Tapping Screw-B 3.0X10 ZMC2BL (Black) 4 01

F07 Pickup B-Band 29S

F08 Adhesive Tape 12X50 t=0.2 (QC66730)

F09 Cushion 8X12 t=1

ACCESSORIES

H01 AC Adapter PA-D09 J J

H01 AC Adapter PA-D09 UL U,C

H01 AC Adapter PA-D09 CE H

H02 Stereo Earphones

H03 Soft Case

24173400

QC665900

QC653700

QC655100

QC667000

QC653600

QC655400

QC667100

QC666400

03714060

QC656400

QC655200

20454100

03377460

QC656500

QC653400

QC653500

QC693600

QC653300

QC699200

QC653100

QC699200

QC667000

QC660000

V8729900

QC662400

20404200

EP600140

QC624400

QC679000

V8285200

V8285300

V8285400

QC667400

QC666900

RANK

Accessories

H01

AC Adapter

H02

Stereo Earphones

H03

Soft Case

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

PANEL ASSEMBLY

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

REF NO.

PART NO. DESCRIPTION REMARKS

QTY

: New Parts RANK: Japan only

PANEL ASSEMBLY SLG-100N (QC66720)

1 Control Panel (Black)

2 Battery Cover (Black)

3 AUX Knob AUX VOL 04

4 Rotary Knob VOLUME,BASS,TREBLE 3 05

5 DC Cord Column 02

6 Circuit Board MA

7 Circuit Board AUX

8 Jack Holder

9 Connector Assembly LINE PHR-3P (QC66160)

9a Jack JL2B X-G7639 LINE OUT 03

10 Hexagonal Nut (Black) 01

11 Flat Washer (Black) 01

12 Connector Assembly BT PHR-2P L=280 with Battery snap

13 Sponge 20X37 t=4 (Gray) (QC66190) 2

14 Adhesive Tape 5X20 t=0.2 (QC66730)

15 Name Plate Sticker (QC66230)

16 Bind Head Tapping Screw-B 3.0X10 ZMC2BL (Black) 4 01

17 Cushion 8X12 t=1

18 Flat Washer 3.0X8X0.5 ZMC2BL (Black) 2

19 Cushion 20X20X13 (Black) (QC70870)

QC659900

QC660200

V2300100

QC187700

VC407100

V8729700

V8729800

QC660100

LB201120

AA820860

AA820850

QC661500

EP600140

QC679000

QC689700

RANK

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

SLG-100N

REF NO.

PART NO. DESCRIPTION REMARKS

QTY

: New Parts RANK: Japan only

ELECTRICAL PARTS SLG-100N

Circuit Board MA (V872950)(X2450C0)

Circuit Board AUX (V872950)(X2450C0)

Circuit Board PUP (V872950)(X2450C0)

Circuit Board MA (V872950)(X2450C0)

LED Holder LEH5-4.5T

C01 Mylar Capacitor 0.047u 50V J 01

C02 Mylar Capacitor 0.012u 50V J 01

C03 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C04 Ceramic Capacitor-SL(chip) 150P 50V J 01

C05 Mylar Capacitor 0.018u 50V J 01

C06 Mylar Capacitor 0.01u 50V J 01

C07 Ceramic Capacitor-B (chip) 3300P 50V K 01

C08 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C09 Mylar Capacitor 2200P 50V J 01

C10 Mylar Capacitor 560P 50V J 02

C11 Mylar Capacitor 0.068u 50V J 02

C12 Ceramic Capacitor-CH(chip) 22P 50V J 01

C13 Ceramic Capacitor-CH(chip) 22P 50V J 01

C14 Ceramic Capacitor-SL(chip) 100P 50V J 01

C15 Mylar Capacitor 0.01u 50V J 01

C16 Mylar Capacitor 0.022u 50V J 01

C17 Mylar Capacitor 0.022u 50V J 01

C18 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C19 Ceramic Capacitor-B (chip) 3300P 50V K 01

C20 Mylar Capacitor 0.022u 50V J 01

C21 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C22 Mylar Capacitor 0.022u 50V J 01

C23 Ceramic Capacitor-B (chip) 3300P 50V K 01

C24 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C25 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C26 Ceramic Capacitor-SL(chip) 100P 50V J 01

C27 Ceramic Capacitor-SL(chip) 100P 50V J 01

C28 Mylar Capacitor 0.047u 50V J 01

C29 Mylar Capacitor 0.047u 50V J 01

C30 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C31 Mylar Capacitor 0.01u 50V J 01

C32 Mylar Capacitor 0.01u 50V J 01

C33 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C34 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C35 Mylar Capacitor 0.022u 50V J 01

C36 Mylar Capacitor 0.022u 50V J 01

C37 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C38 Ceramic Capacitor-B (chip) 1500P 50V K 01

C39 Ceramic Capacitor-B (chip) 1500P 50V K 01

C40 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C41 Mylar Capacitor 0.068u 50V J 02

C42 Mylar Capacitor 0.068u 50V J 02

C43 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C44 Ceramic Capacitor-B (chip) 4700P 50V K 01

C45 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C46 Ceramic Capacitor-SL(chip) 330P 50V J 01

C47 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

C48 Ceramic Capacitor-SL(chip) 150P 50V J 01

-51 Ceramic Capacitor-SL(chip) 150P 50V J 01

C52 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

-55 Ceramic Capacitor-F (chip) 0.1u 25V Z 01

CC01 Electrolytic Capacitor-KS 100u 6.3V 01

-03 Electrolytic Capacitor-KS 100u 6.3V 01

CC04 Electrolytic Capacitor-KS 220u 10V

CC05 Electrolytic Capacitor-KS 220u 10V

CC06 Electrolytic Capacitor-BP 0.47u 50V 01

CC07 Electrolytic Capacitor-KS 100u 16V 01

CC08 Electrolytic Capacitor-KS 10u 16V 01

CC09 Electrolytic Capacitor-KS 100u 16V 01

CC10 Electrolytic Capacitor-KS 4.7u 25V 01

CC11 Electrolytic Capacitor-KS 1u 50V 01

CC12 Electrolytic Capacitor-KS 1u 50V 01

CC13 Electrolytic Capacitor-KS 47u 16V 01

V8729700

V8729800

V8729900

V8729700

QC662200

UA654470

UA354120

US145100

US062150

UA654180

UA654100

US063330

US145100

UA653220

UA652560

UA654680

US061220

US062100

UA654100

UA654220

US145100

US063330

UA654220

US145100

UA654220

US063330

US145100

US062100

UA654470

US145100

UA654100

US145100

UA654220

US145100

US063150

US145100

UA654680

US145100

US063470

US145100

US062330

US145100

US062150

US145100

UM388100

V6796100

UN865470

UM398100

UM397100

UM398100

UM406470

UM416100

UM397470

RANK

ELECTRICAL PARTS

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Other manuals for Silent Guitar SLG-100N

Table of contents

Other Yamaha Musical Instrument manuals

Yamaha

Yamaha Clavinova CLP-110 Assembly instructions

Yamaha

Yamaha Electric Grand CP-70B User manual

Yamaha

Yamaha PDP-100 Assembly instructions

Yamaha

Yamaha Clavinova CLP-152S Assembly instructions

Yamaha

Yamaha PORTATONE PSR-140 User manual

Yamaha

Yamaha P-125a User manual

Yamaha

Yamaha CN-70 User manual

Yamaha

Yamaha Clavinova CVP-50 User manual

Yamaha

Yamaha AES620HB User manual

Yamaha

Yamaha TRB-6II User manual

Yamaha

Yamaha Electone EL-28 User manual

Yamaha

Yamaha Clavinova CLP-360 User manual

Yamaha

Yamaha YEP-842S User manual

Yamaha

Yamaha Electone EL-37 User manual

Yamaha

Yamaha AW2816 User manual

Yamaha

Yamaha Electone STAGEA ELB-01 User manual

Yamaha

Yamaha YDP-113 Assembly instructions

Yamaha

Yamaha YOB-431 User manual

Yamaha

Yamaha J-3000 User manual

Yamaha

Yamaha CP1 Instruction Manual

Yamaha

Yamaha Portable Grand DGX-660 User manual

Yamaha

Yamaha EZ-AG User manual

Yamaha

Yamaha PSR-E363 User manual

Yamaha

Yamaha AW4416 User manual

Popular Musical Instrument manuals by other brands

Princeton

Princeton SP-88 user manual

Ovation

Ovation Breadwinner 1251-6 owner's manual

Casio

Casio CT-S500 user guide

Technics

Technics SX-PC25 Service manual

Adagio

Adagio KDP8865 owner's manual

Roland

Roland -50 manual

Peavey

Peavey Nitro C-3 operating guide

Lowrey

Lowrey Encore A200 owner's guide

Lowrey Organs

Lowrey Organs Tlocks-25 Holiday Console Service manual

Roland

Roland AT-20R owner's manual

BYO Guitar

BYO Guitar Explorer Guitar Kit Assembly instructions

SONIC COUTURE

SONIC COUTURE MORPHEUS user guide

Allen Organ Company LLC

Allen Organ Company LLC MDS-70-S owner's manual

Allen Organ Company LLC

Allen Organ Company LLC MDS-75 user manual

Allen Organ Company LLC

Allen Organ Company LLC MDS-15 user manual

Generalmusic

Generalmusic RPStudio Service manual

Kawai

Kawai ES4/es1P Service manual

Casio

Casio Piano Sound CPS-60 Operation manual

Yamaha Silent Guitar SLG-100N User manual

Popular Musical Instrument manuals by other brands