Yamaha OneHome LPX-510 Installation guide

HomeLogic LLC 100 Hoods Lane Marblehead, MA 09145 Phone [phone] Fax [phone]
OneHome

Display Integration Note
Manufacturer: Yamaha
Model Number(s): LPX-510
Comments:
Document Revision Date: 2/3/2006
O VERVIEW AND S UPPORTED F EATURES
The projector includes an RS-232 connection to integrate with the OneHome system and provide reliable
communications.
THE PROJECTOR SUPPORTS THE FOLLOWING FEATURES:
Input Selection and Power Control: Select any available input source, turn display off or on.
THE PROJECTORS DO NOT CURRENTLY SUPPORT THE FOLLOWING FEATURES:
Display Modes: Changing display modes (such as Zoom or 4:3), is not supported from the OneHome
system.
I NSTALLATION O VERVIEW
1. During the rough-in phase install the necessary power and video cabling for the projector installation.
2. Also during the rough-in phase, run a Cat5 wire from the location of the projector back to the Network
Assembly of the OneHome system to provide the serial connection needed to control the display.
3. Refer also to the RS-232 Connection Options Integration Note for other serial connection options.
4. Install the projector and related components.
5. Test the projector to ensure that the sources play correctly stand-alone.
6. Program the projector to enable RS-232 communications. Refer to Projector Programming.
7. Connect the OneHome system to the projector electrically. Refer to Connection Diagrams.
8. Configure the OneHome system for the projector and confirm communication between the projector
and the HomeBrick. Refer to HomeLogic Configuration Details.
9. Test the system by changing sources to confirm the correct video appears.

2 of 5
C ONNECTION D IAGRAMS
BILL OF MATERIALS
# Device Manufacturer Part Number Protocol Connector Type Notes
1 DB9F to RJ45 NULL Adapter HomeLogic HA-CB-328 RS-232 DB-9 Female X RJ-45 Female
2 Cat5 Cable Assy. Installer N/A RS-232 RJ-45 Male X RJ-45 Male Must terminate all 8 conductors
3 Network Assembly HomeLogic HW-NA-18X4 RS-232 RJ-45 Female X DB-9 Female / USB
4 HomeBrick HomeLogic HW-HB-1080 RS-232 DB9 Male / USB

3 of 5
P ROJECTOR P ROGRAMMING
Set the communication settings on the projector using the IR remote included with the projector, and the
projector’s on screen setup menus:
1. Press the Menu button on the remote to bring up the on-screen menu.
2. Press right (+) button once to scroll to Setup, then press enter (center of the round directional
button).
3. Press the down arrow button to scroll to operation, then press enter.
4. Press the down arrow button to scroll to Standby Mode, then press enter.
5. Press the down arrow button to select RS-232 on, then press enter.
6. Press the Escape button a few times to exit the on-screen menu.
7. Power down and restart the projector to save the changes.

4 of 5
H OME L OGIC C ONFIGURATION D ETAILS
The following table provides settings used in the HomeLogic Configurator. Please refer to the Configurator Reference Guide for more details.
o“<Select>” Select the appropriate item from the list (or drop-down) in the Configurator.
o“<User Defined>”, etc. Type in the desired name for the item.
O
PTION 1: RS-232
Devices Variable Name Setting Comments
Communication Devices Name
<User Defined> (Default:
Yamaha LPX-510
)
Type Serial Port
Communication Type Standard Connection
Location <User Defined> (Not Required)
COM Port <Select>
Video Display Name
<User Defined> (Default:
Yamaha LPX-510
)
Device Type Yamaha LPX-510
Location <User Defined> (Not Required)
COM Device <Select> (Default:
Yamaha LPX-510
)

5 of 5
C OMMON M ISTAKES