Yard force LW C02 User manual

myRobotcenter
The expert for robots in your home
With one click to the online shop
myRobotcenter.eu myRobotcenter.co.uk

READ & UNDERSTAND
INSTRUCTION MANUAL
Save all warnings and instructions for future reference.
20V CORDLESS PRESSURE CLEANER
AQUAJET
Original Instructions
GB
LW C02
Q0W-SP01-320

2 3
Read this manual carefully prior to assembling and
operating the pressure cleaner. It is dangerous to operate
this product without being familiar with these instructions.
Keep this manual in a safe place and have it ready for
future reference.
A
B
1
2
34
5
6
7
8
a
b
d
c
f
ghi
j
e
k
m
l

4 5
2
C
E
FG
D
HI
K L
M N
J
%
1
1
3
2
2
2
1
1
2
+
1
1
2

6 7
LW C02 Original Instructions
CONTENT
Intended use 08
General safety warnings 08
Product safety warnings 11
Symbols 17
Technical data 21
Description of product 22
Installation 23
Operation 25
Maintenance and storage 26
Troubleshooting 28
CE declaration 29
O
Q
P
1
2
1
2

8 9
GENERAL SAFETY WARNINGSINTENDED USE
3. WARNING: This appliance has been designed for
use with the cleaning agent supplied or recommended
by the manufacturer. The use of other cleaning agents
or chemicals may adversely affect the safety of the
appliance.
4. WARNING: Pressure jets can be dangerous if subject
to misuse. The jet must not be directed at persons, live
electrical equipment or the appliance itself.
5. WARNING: Do not use the appliance within range of
persons unless they wear protective clothing.
6. WARNING: Do not direct the jet against yourself or
others in order to clean clothes or foot-wear.
7. WARNING: Risk of explosion - Do not spray flammable
liquids.
8. WARNING: Pressure cleaners shall not be used by
children or untrained personnel.
9. WARNING: Pressure hoses, fittings and couplings are
important for the safety of the appliance. Use only hoses,
fittings and couplings recommended by the manufacturer.
10. WARNING: To ensure appliance safety, use only
original spare parts from the manufacturer or approved
by the manufacturer.
11. WARNING: Water that has flowed through backflow
preventers is considered to be non-potable.
12. WARNING: The appliance should be disconnected
from its power source during cleaning or maintenance
and when replacing parts or converting the appliance to
another function by removing the battery pack.
13. WARNING: Do not use the appliance if important
parts of the appliance are damaged, e.g. battery pack,
pressure hoses, trigger, lance, nozzles.
The appliance is intended for cleaning the walls of buildings, facades,
terraces, footpaths, garden equipment, appliancery, vehicles and tools.
The appliance is to be used only for its prescribed purpose. Any other
use is deemed to be a case of misuse. The user/operator and not the
manufacturer will be liable for any damages or injuries of any kind caused
as a result of misuse.
Please note that our equipment has not been designed for use in
commercial, trade or industrial applications. Our warranty will be voided if
the appliance is used in commercial, trade or industrial businesses or for
equivalent purposes.
GENERAL SAFETY WARNINGS
Read the following safety instructions to prevent
damage or injury to persons or property.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS
APPLIANCE
WARNING: When using this product basic
precaution should always be followed, including the
following:
1. Appliances shall not be used by children. Children
should be supervised to ensure that they do not play with
the appliance.
2. This appliance can be used by people with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.

10 11
14. WARNING: Always remove the battery pack when
leaving the appliance unattended.
15. WARNING: In the event of contact with or spillage of
detergents, flush with water. If liquid contacts eyes, seek
medical assistance immediately.
16. The liquid from appliance must not be directed
towards equipment containing electrical components,
such as the interior of ovens.
17. Rechargeable batteries are to be removed from the
appliance before being charged.
18. Batteries are to be inserted with the correct polarity.
19. Exhausted batteries are to be removed from the
appliance and safely disposed of.
20. If the appliance is to be stored unused for a long
period, the batteries should be removed.
21. The supply terminals are not to be short-circuited.
22.Cleaning and user maintenance shall not be made by
children without supervision
23.The appliance is not to be used if it has been dropped,
if there are visible signs of damage or if it is leaking
24.Keep the appliance out of reach of children when it is
energized or cooling down.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE
WARNING! When using the product, the safety
rules must be followed. For your own safety and that
of bystanders, please read these instructions before
operating the product. Please keep the instructions
safe for later use.
Training
1. Read the instructions carefully. Be familiar with the
controls and the proper use of the product.
2. Never allow people unfamiliar with these instructions or
children to use the product. Local regulations can restrict
the age of the operator.
3. Keep in mind that the operator or user is responsible
for accidents or hazards occurring to other people or their
property.
4. WARNING: Water that has flowed through backflow
preventers is considered to be non-potable.
5. WARNING: Risk of explosion – Do not spray flammable
liquids.
6. Do not use the equipment near flammable liquids or
gases. In case of non-observance, there is a risk of fire of
explosion.
Preparation
1. Never operate the product while people, especially
children or pets are nearby.
2. WARNING: the appliance is not designed for
connecting to tap water. If necessary, please use only
with a water backflow preventer or inlet hose-set
GENERAL SAFETY WARNINGS PRODUCT SAFETY WARNINGS

12 13
PRODUCT SAFETY WARNINGS PRODUCT SAFETY WARNINGS
approved by IEC 61770.
3. WARNING: Pressure hoses, fittings and couplings are
important for the safety of the appliance. Use only hoses,
fittings and couplings recommended by the manufacturer.
Operation
1. Use the product only in daylight or good artificial light.
2. Never operate the product if battery pack, safety
devices, hoses, switch or trigger is damaged.
3. Before use, check the controls and proper use of the
product.
4. Before using the product and after any impact, check
for signs of wear or damage and repair as necessary.
5. Always disconnect the product from the battery
a. Whenever leaving the product unattended;
b. Before clearing a blockage;
c. Before checking, cleaning or working on the
product;
d. Whenever the product starts vibrating abnormally.
6. Vehicle tyres/tyre valves are susceptible to damage
from the high-pressure jet and may burst. The first
indication for this is a discolouration of the tyre. Damaged
vehicle tyres/tyre valves are perilous. Keep a minimum jet
distance of 30cm during cleaning.
7. WARNING: There is a risk of kickback and sudden
torque load against the jet spray when the device is
opened. Ensure that you are standing firmly and that you
are holding the gun securely, otherwise you could injure
yourself or other people.
8. Never use replacement parts or accessories not
provided or recommended by the manufacturer.
9. Avoid using the product in bad weather conditions
especially when there is a risk of lightning.
10. Do not expose the product to rain.
Battery pack
1. Fully charge battery pack before first use.
2. Recharge battery pack immediately when the power
output
starts to slow. DO NOT CONTINUE TO USE PRODUCT
WHEN BATTERY LEVEL IS LOW.
3.To prevent serious damage to the battery, charge in
temperatures above 5ºC and below 45ºC. Longest life
and best performance can be achieved when battery is
charged at room temperature.
4. If the battery temperature is above 45ºC it must be
allowed to cool before putting it into the charging station.
5. To reduce the risk of explosion, ensure the battery
pack is not left in the sun for extended periods of time
and that it is kept away from fire.
6. Do not carry individual battery packs in your pockets
or bag as they could short-circuit against other metal
items.
7. Should a li-ion battery catch fire, ensure to use the
correct fire extinguisher to combat the fire. DO NOT
THROW WATER ON A BURNING LI-ION BATTERY.
8. If the battery pack becomes too hot during charging,
disconnect and switch off immediately. Contact the
service centre directly.
9. Do not attempt to open the battery yourself.
10. When battery pack is not in use, keep it away from

14 15
other metal objects such as paperclips, coins, keys, nails,
screws or other small metal objects that can make a
connection from one terminal to another.
11. Only use the authorised battery pack by maufacturer.
model: B0P-SP07-20-ZJ.
Charging
1. Recharge only with the charger specified by the
manufacturer. Do not use the original charger on other li-
ion batteries or on any other type of battery as this can
increase the risk of fire or explosion.
2. Check the battery charger, cable and plug before
each use. Do not use the battery charger if damaged. Do
not open the battery charger yourself; charger must be
repaired by qualified personnel using original spare parts.
3. The charger is designed to use a standard household
230-240 V~ 50/60Hz power source, ensure that the plug
matches the outlet.
4. Never modify the plug in any way, this will reduce the
risk of electric shock.
5. Do not abuse the cord of charger. Never use the cord
for carrying, pulling or unplugging the charger. Keep the
cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric
shock.
6. Make sure the charger cord is situated so that it will
not be stepped on, tripped over or get damaged.
7. Keep the battery charger clean. Contamination can
increase the risk of electric shock.
8. Protect the battery charger from rain and moisture. If
water accesses the battery charger there is an increased
risk of electric shock.
9. Battery will heat up whilst charging. To reduce the
risk of fire, do not operate battery charger on flammable
surfaces such as paper or textiles.
11. Only use the authorised charger by maufacturer.
model: B0Q-SP06-20ZB.
Maintenance and storage
• Disconnect the product from the power supply (i.e.
remove the plug from the power supply or the battery
pack) and check for damage after use.
• Disconnect the product from the power supply (i.e.
remove the plug from the power supply or the battery
pack) before carrying out maintenance or cleaning work.
• Leave the hose connected to the appliance and spray
gun while the unit is pressurised. It is dangerous to
detach the hose while the unit is pressurised.
• Use only the manufacturer’s recommended replacement
parts and accessories.
• Inspect and maintain the product regularly. Have the
product repaired only by an authorised service centre or
similar qualified specialist.
• When not in use, store the product out of the reach of
children.
Vibration and noise reduction
To reduce the impact of noise and vibration emission,
limit the time of operation, use low vibration and low
noise operating modes as well as wearing personal
protective equipment.
PRODUCT SAFETY WARNINGS PRODUCT SAFETY WARNINGS

16 17
Take the following points into account to minimize the
vibration and noise exposure risks:
1. Only use the product as intended by its design and
these instructions.
2. Ensure that the product is in good condition and well
maintained.
3. Keep tight grip on the handles/gripping surface.
4. Maintain this product in accordance with these
instructions and keep it well lubricated (where
appropriate).
5. Plan your work schedule to spread any high vibration
tool use across a longer period of time.
Servicing
• Have your tool repaired by an authorised service agent.
This tool is manufactured in accordance with the relevant
safety regulations. To avoid danger, equipment must only
be repaired by qualified technicians.
• Only use parts and accessories made for this appliance
by the manufacturer. Failure to do so can result in per-
sonal injury.
Safety symbols
The purpose of safety symbols is to attract your
attention to any possible dangers. The safety symbols
and their explanations deserve your careful attention
and full understanding. The symbol warnings do not, by
themselves, eliminate any danger. The instructions and
warnings they give are no substitute for proper accident
prevention measures.
WARNING: Be sure to read and understand
all safety instructions within this operator’s
manual, including all safety alert symbols such as
“DANGER”, “WARNING”, and “CAUTION” before
using this tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious personal injury.
SAFETY ALERT SYMBOLS: Indicate DANGER,
WARNING, or CAUTION. May be used in conjunction
with other symbols or pictographs.
Symbol meanings
This page depicts and describes safety symbols that may
appear on this product. Read, fully understand and follow
all instructions on the appliance before attempting to
assemble and operate.
PRODUCT SAFETY WARNINGS SYMBOLS

18 19
To reduce the risk of injury, user must read
instruction manual carefully.
Appliance not suitable for connection to the
potable water mains (kitchen tap).
Water that has flown through backflow
preventers
is considered to be non-potable.
The appliance is not intended to be connected
to
an indoor tap. If necessary, please use only with
a water backflow preventer or an inlet hose-set
approved by IEC 61770.
WEEE symbol. Waste electrical products should
not be disposed of with household waste.
Please recycle where facilities exist. Check with
your local authority or local store for recycling
guidelines
The product complies with the applicable
European directives and an evaluation method
of conformity for these directives was done.
SYMBOLS
Warning symbols on the battery pack
To reduce the risk of injury, user must read the
instruction manual carefully.
Do not throw into water.
Do not throw to fire.
Do not subject the battery to strong sunlight over
long periods of time. Do not leave on a heater
(max.45°C).
Batteries contain Li-ion. Do not dispose of
waste batteries in domestic waste. Contact local
authority to find out how to dispose of batteries.
WEEE symbol. Waste electrical products should
not be disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or local store for recycling advice.
SYMBOLS

20 21
Warning symbols on the charger
To reduce the risk of injury, user must read the
instruction manual carefully.
The charger is for indoor use only.
Double insulation
WEEE symbol. Waste electrical products should
not be disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or local store for recycling advice.
The product complies with the applicable
European directives and an evaluation method of
conformity for these directives was done.
SYMBOLS
Model LW C02
Nominal voltage of product
with battery 20 V / 2.5 Ah
water inlet pressure < 6 Bar
Working pressure Eco: 14 Bar High: 22 Bar
Working ow rate 160 L/h
Weight 4.5 kg
Battery pack Model B0P-SP07-20-ZJ
Battery capacity 2.5 Ah
Battery charging time Max. 60 min
Battery charger Model VDE: B0Q-SP06-20ZA
BS: B0Q-SP06-20ZB
Input 220-240 V AC, 50/60 Hz 65W
Output 20 V , 2.4 A
Protection class II
TECHNICAL DATA

22 23
INSTALLATION
Install the lance (Fig. C)
Align the lance to the main housing and push down firmly and then rotate the lance to secure
in place.
NOTE: Make sure that the lance button is position on the top side.
Fitting the 3 in 1 nozzle (Fig. D)
press and hold down the lance nozzle lock button and then align the nozzle spigot and
assemble into the lance and release the lock button.
Choose your water source (Fig. E)
1. Using the Aquajet with your garden hose pipe – attach the hose pipe to the Aquajet
connector and make sure that it is locked into position
2. Using the Aquajet with a portable water source – assemble the filter to the short portable
hose pipe supplied with the product and then connector the other hose connector to the
Aquajet connector and place into the water source
Connect the hose
Attach the hose to the Aquajet connector, make sure it is locked in to position when you hear
the sound "click" .
In keeping with current regulations a pressure washer must never be operated from the
drinking water mains supply without a controllable backflow preventer. A suitable backflow
preventer in conformity with EN 12729 type BA must be used.
Water that has passed through a backflow preventer is classified as undrinkable.
NOTE: A backflow preventer is available from specialist retailers.
NOTE: Water pressure out from the tap should not higher than 0.6Mpa.
DESCRIPTION OF PRODUCT
Parts description (Fig. A)
1. Lance
2. Eco/Pressure Switch Button
3. Safety Lock Button
4. Battery Pack
5. ON/OFF Switch Trigger
6. Handle Rotary Lock Button
7. Water Inlet/ Hose Connector
8. 3 in 1 Nozzle
Check the delivery parts (Fig. B)
Remove the appliance from its packaging carefully and make sure that all of the
following parts are present:
a. 3 in 1 nozzle
b. AQUAJET housing
c. Hose
d. Water filter
e. Lance
f. Battery pack
g. Charger
h. Foam sprayer
i. Net bag
j. Brush
k. Instruction manual
l. Quick start guide
m. Foldable bucket
WARNING: If any parts are damaged or missing, do not operate
this tool until these parts have been replaced. Failure to heed this
warning could result in serious personal injury.
NOTE: Always recycle the packaging in accordance with local
recycling guidelines.

24 25
OPERATION
Switch ON: (Fig. J)
1. Press the safety lock button with your thumb.
2. Depress the switch lever. Once the machine has started then release your thumb from
the lock button.
3. Hold the trigger down, as it will take at least 15 seconds to draw the water from the
source.
NOTE: Be prepared for the recoil force of the emitted water jet! Ensure that you are standing
firmly and that you are holding decive securely with both hands, otherwise you could injure
yourself or other people.
Switch OFF:
Release the switch trigger.
Operating the AQUAJET
Adjusting rotary handle (Fig. K)
1. Press and hold down the rotary handle button.
2. Adjust the handle to your preferred working position and then release the button.
3 in 1 nozzle (Fig. L)
Whilst holding the lance rotate the nozzle to your selected position making sure that the
nozzle is aligned with the lance arrow
Adjusting working pressure: (Fig. M)
There are 2 working pressure settings.
Press the button once or twice to select thepreferred setting (High & low)
Using the brush (Fig. N)
Remove the lance and nozzle.
Align the brush to the main housing and push down firmly and rotate to secure in place
when using the brush it is advised to use the ECO setting pressure to save water.
Using the foam sprayer (Fig. O&P)
Fill the bottle with detergent, using the brands recommended mixture levels
Align the detergent bottle to the main housing and push down and rotate to secure in place.
Charging the battery pack
NOTE: Remove the battery pack from the charger after it has been fully charged.
NOTE: Battery should be fully charged before first use.
NOTE: Make sure the mains voltage is the same as rating label which is located on the
charger.
1. Connect the charger to a power supply. Red LED will light up.
2. To insert the battery pack into the charger, align the raised ribs of the battery pack with
the grooves of the charger then push it in. (Fig. F)
3. The red LED light of the charger will light up and then the green light flashes during
normal charging.
4. After charging is complete, the charger light will turn to a solid green light.
5. Once the battery is fully charged , depress the battery release button and then remove
the battery pack. (Fig. F)
Power indicator (See Fig. G)
This Li-Ion battery pack is equipped with a power indicator which is used to show the battery
pack’s remaining charge. Press the power indicator button to check battery charge as picture
showed. The indicator will stay lit for approximately 4 seconds.
To obtain the best life from the battery
1. Never allow the battery to completely discharge before recharging. The battery pack
should be placed on the charger whenever the battery pack is noticeably running down
or the tool no longer performs a task it previously performed.
2. Avoid conducting short charges. Make sure that the battery is fully charged each time by
allowing the charger to complete its full charging cycle.
3. Avoid allowing loose items like screws or nails etc. to be stored with battery packs as
these or similar items can short battery packs and cause a fire or explosion.
4. Always unplug the charger when not in use and store in a dry and secure place.
5. Avoid charging or storing your battery in temperatures below 5°C and above 45°C.
6. After use, allow the battery pack to cool down for approximately 30 minutes before
attempting to recharge.
To insert the battery pack (Fig. H)
1. Align the groove on the battery pack with the corresponding ribs in the receptacle of the
device.
2. Insert the battery pack with moderate force until it was locks in to place.
WARNING: Only use Yard force 20V original battery pack!
To remove the battery pack from the tool (Fig. I)
1. Press the battery pack release button.
2. Remove the battery pack from the tool.
OPERATION
SOFT MEDIUM HARD
WARNING:
( Do not rotate the nozzle when operating
the Aquajet )

26 27
MAINTENANCE AND STORAGE MAINTENANCE AND STORAGE
WARNING:
Risk of electric shock
Before performing any repair work, always ensure that the battery pack has been removed.
Overview of cleaning
1. Clean the appliance. Wipe the unit with a slightly damp cloth. Do not clean the appliance
using a high-pressure water jet.
2. Clean the inlet adaptor and filter with a needle and water. Clear debris from the inlet
adaptor. (Fig. Q)
Hose filter cleaning section (Fig. Q)
The pressure washer is equipped with a water filter to protect the pump. If the filter is not kept
clean, the water flow to the appliance will be restricted and the pump may be damaged.
1. Disassemble the filter from the hose. Remove transfer adapter and take out filter.
2. Rinse filter until it is free of debris and blockages.
3. Replace the filter and inlet adapter.
Maintenance
This appliance is maintenance-free.
Spare parts
Please contact the after-sales centre if you need order following spare parts:
Storing
WARNING: Always ensure that the battery pack has been removed.
Store the appliance in a dry and well ventilated area.
When the appliance is not going to be used for an extended period of time, be sure to remove
the cleaning agent and drain all remaining water from the hose.
Transport
If shipping, use the original packaging wherever possible.
Disposing of the appliance
This appliance must not be disposed of in household rubbish. You must dispose of such old
electrical and electronic appliances separately.
Please check with your local authority how to correctly dispose of your old appliance.
Disposing of the packaging
The packaging consists of cardboard and correspondingly marked sheets that should be
recycled. Be sure to recycle this packaging in line with local recycling guidelines.
Battery maintenance
Use the following procedures to achieve the best battery life:
1. Protect the battery against moisture and water.
2. We recommend to store the battery only within temperature range of 5 ℃to 45 ℃. Do not
leave the battery in direct sunlight for extended periods of time.
3. Clean the battery regularly with a soft, clean and dry brush.
4. If you do not use the product for a long time, remember to charge and discharge the
battery pack once every 6 months.
WARNING: If you have used the Aquajet with salt water, please make sure that you
thoroughly rinse out with clean water.

28 29
TROUBLESHOOTING
Fault/
malfunction Cause Remedy
Appliance does not
turn ON
Battery pack discharged? Fully charge the battery pack
Battery pack is not connected
correctly. Install the battery pack once again.
Safety lock off button has not
been depressed
Check start procedure
1. depress lock off
2. depress switch lever
m/c PCB activated. Restart the device
Pump frozen Check and allow the appliance to
thaw
Appliance water
pressure too low
Eco button active (low motor
speed)
Press the Eco button once when
operating the machine (higher motor
speed)
Hose damaged or leaks in the
connections.
Change the hose - check the hose
for leaks and repair - securely tighten
the screw connection
Filter blocked Clean lter on the appliance
Hose is trapped or kinked Straighten out the hose
Inadequate water supply Check water suply levels
The appliance /water source
height is too large
Lower the appliance - maximum
working height @1.5M- 5ft
Water leaks
The nozzle is not aligned with
lance correctly
Re-align the nozzle correctly with the
lance
O-ring split/broken Replace the accessory or change
the O-ring
Attachment are not installed
correctly
Remove & re-install the attachment
correctly
Accessories broken Replace accessories
Detergent cannot
spray out
Speed setting on Low Select speed setting High
Deposits or restrictions in the
detergent system
Flush with clean water and remove
all debris
Battery not charging Battery pack too hot Allow battery pack to cool down
before re-charging
CE DECLARATION
Declaration of Conformity
We
SUMEC UK
Unit A&B Escrick Business Park Escrick, York YO19 6 FD/ United Kingdom
Declare that the product:
Description: 20V Cordless Pressure Washer
Q0W-SP01-320
LW C02
Function: Clean the walls of buildings etc.
Complies with the essential health and safety requirements of the following directives:
EC Directive 2011/65/EU and its amendment Directive (EU) 2015/863 (RoHS)
Standards and technical specification referred to :
EN 60335-1: 2012+A11+A13
EN 60335-2-54: 2008+A11+A1
EN 62233: 2008
EN 55014-1: 2006+A1+A2
EN 55014-1: 2017
EN 55014-2: 2015
Authorized Signatory
Date: 30.04.2019
Signature:________________________
Place: York
Name: Mariana Hall
General Manager
SUMEC UK Co.,Ltd.
Unit A&B Escrick Business Park
Escrick,York YO19 6 FD
United Kingdom
Before performing any repair work, always ensure that the battery
pack has been removed from the Aquajet.
WARNING:

30 31
CE DECLARATION CE DECLARATION
Declaration of Conformity
We
MEROTEC GmbH,
Otto-Brenner-Straße 8,
47877 Willich/ Deutschland
Declare that the product:
Description: 20V Cordless Pressure Washer
Q0W-SP01-320
LW C02
Function: Clean the walls of buildings etc.
Complies with the essential health and safety requirements of the following directives:
EC Directive 2011/65/EU and its amendment Directive (EU) 2015/863 (RoHS)
Standards and technical specification referred to :
EN 60335-1: 2012+A11+A13
EN 60335-2-54: 2008+A11+A1
EN 62233: 2008
EN 55014-1: 2006+A1+A2
EN 55014-1: 2017
EN 55014-2: 2015
Authorized Signatory
Date: 30.04.2019
Signature:________________________
Place: Willich
Name: Roland Menken
General Manager
MEROTEC GmbH,
Otto-Brenner-Straße 8,
47877 Willich/ Deutschland
Declaration of Conformity
We
SUMEC France Sarl
59 bis Rue du Mûrier
37540 Saint Cyr Sur Loire, France
Declare that the product:
Description: 20V Cordless Pressure Washer
Q0W-SP01-320
LW C02
Function: Clean the walls of buildings etc.
Complies with the essential health and safety requirements of the following directives:
EC Directive 2011/65/EU and its amendment Directive (EU) 2015/863 (RoHS)
Standards and technical specification referred to :
EN 60335-1: 2012+A11+A13
EN 60335-2-54: 2008+A11+A1
EN 62233: 2008
EN 55014-1: 2006+A1+A2
EN 55014-1: 2017
EN 55014-2: 2015
Authorized Signatory
Date: 30.04.2019
Signature:________________________
Place: Saint Cyr Sur Loire
Name: Rodolphe Dubois
General Manager
SUMEC France Sarl
59 bis Rue du Mûrier
37540 Saint Cyr Sur Loire, France