YASKAWA VIPA TP-ECO User manual

TP-ECO | 62K-NHC0 | Manual
HB160 | TP-ECO | 62K-NHC0 | en | 17-09
VIPA HMI
Touch Panel - TP610LC/+
www.vipa.com/en/service-support/manual

62K-NHC0_000_TP610LC/+,4,EN - © 2017
VIPA GmbH
Ohmstr. 4
91074 Herzogenaurach
Telephone: [phone]
Fax: [phone]
Email: [email protected]
Internet: www.vipa.com

Table of contents
1 General.................................................................................................................... 5
1.1 Copyright © VIPA GmbH ................................................................................. 5
1.2 About this manual............................................................................................. 6
1.3 Safety information............................................................................................. 7
2 Hardware description............................................................................................. 8
2.1 Safety information for users.............................................................................. 8
2.2 Properties......................................................................................................... 8
2.3 Structure......................................................................................................... 10
2.3.1 Overview...................................................................................................... 10
2.3.2 Interfaces..................................................................................................... 12
2.3.3 Memory management.................................................................................. 15
2.4 Dimensions..................................................................................................... 15
2.5 General data................................................................................................... 17
2.6 Technical data................................................................................................. 18
2.6.1 62K-NHC0-DH............................................................................................. 18
2.6.2 62K-NHC0-CB............................................................................................. 20
3 Deployment under Windows CE 6.0 Core.......................................................... 23
3.1 Installation...................................................................................................... 23
3.2 Installation of the optional MPI/PROFIBUS DP interface .............................. 24
3.3 Commissioning............................................................................................... 26
3.3.1 VIPA Startup-Manager................................................................................. 26
3.4 Installation Movicon and Startup-Manager..................................................... 28
3.5 Connection to a PLC system.......................................................................... 31
3.6 Operating system WindowsÒ Embedded CE 6.0 Core................................... 31
3.6.1 General ....................................................................................................... 31
3.6.2 Structure...................................................................................................... 33
3.7 Integrated Server............................................................................................ 37
3.7.1 General........................................................................................................ 37
3.7.2 ftp server...................................................................................................... 38
3.7.3 VNC server.................................................................................................. 39
3.8 Access to the network resources.................................................................... 40
4 Deployment under Windows CE 6.0 Prof........................................................... 43
4.1 Installation...................................................................................................... 43
4.2 Installation of the optional MPI/PROFIBUS DP interface .............................. 44
4.3 Commissioning............................................................................................... 46
4.3.1 VIPA Startup-Manager................................................................................. 46
4.4 Installation Movicon and Startup-Manager..................................................... 49
4.5 Connection to a PLC system.......................................................................... 52
4.6 Operating system WindowsÒ Embedded CE 6.0 Prof.................................... 52
4.6.1 General ....................................................................................................... 52
4.6.2 Structure...................................................................................................... 54
4.7 Integrated Server............................................................................................ 58
4.7.1 General........................................................................................................ 58
4.7.2 ftp server...................................................................................................... 59
4.7.3 http server.................................................................................................... 60
4.7.4 Telnet server................................................................................................ 60
4.7.5 VNC server.................................................................................................. 61
VIPA HMI Table of contents
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 3

4.8 Access to the network resources.................................................................... 63
5 Installation Guidelines......................................................................................... 65
5.1 Basic rules for the EMC-equitable assembly of installations.......................... 65
5.2 EMC-equitable assembly................................................................................ 68
5.3 EMC-equitable cabling................................................................................... 69
5.4 Special precautions providing high noise immunity........................................ 72
5.5 Checklist for the EMC-compliant installation of controllers............................. 73
VIPA HMI
Table of contents
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 4

1 General
1.1 Copyright © VIPA GmbH
This document contains proprietary information of VIPA and is not to be disclosed or used
except in accordance with applicable agreements.
This material is protected by the copyright laws. It may not be reproduced, distributed, or
altered in any fashion by any entity (either internal or external to VIPA), except in accord-
ance with applicable agreements, contracts or licensing, without the express written con-
sent of VIPA and the business management owner of the material.
For permission to reproduce or distribute, please contact: VIPA, Gesellschaft für Visuali-
sierung und Prozessautomatisierung mbH Ohmstraße 4, D-91074 Herzogenaurach, Ger-
many
Tel.: [phone]
Fax.: [phone]
EMail: [email protected]
http://www.vipa.com
Every effort has been made to ensure that the information contained in
this document was complete and accurate at the time of publishing. Nev-
ertheless, the authors retain the right to modify the information.
This customer document describes all the hardware units and functions
known at the present time. Descriptions may be included for units which
are not present at the customer site. The exact scope of delivery is
described in the respective purchase contract.
Hereby, VIPA GmbH declares that the products and systems are in compliance with the
essential requirements and other relevant provisions. Conformity is indicated by the CE
marking affixed to the product.
For more information regarding CE marking and Declaration of Conformity (DoC), please
contact your local VIPA customer service organization.
VIPA, SLIO, System 100V, System 200V, System 300V, System 300S, System 400V,
System 500S and Commander Compact are registered trademarks of VIPA Gesellschaft
für Visualisierung und Prozessautomatisierung mbH.
SPEED7 is a registered trademark of profichip GmbH.
SIMATIC, STEP, SINEC, TIA Portal, S7-300 and S7-400 are registered trademarks of
Siemens AG.
Microsoft and Windows are registered trademarks of Microsoft Inc., USA.
Portable Document Format (PDF) and Postscript are registered trademarks of Adobe
Systems, Inc.
All other trademarks, logos and service or product marks specified herein are owned by
their respective companies.
Contact your local VIPA Customer Service Organization representative if you wish to
report errors or questions regarding the contents of this document. If you are unable to
locate a customer service centre, contact VIPA as follows:
All Rights Reserved
CE Conformity Declaration
Conformity Information
Trademarks
Information product sup-
port
VIPA HMI General
Copyright © VIPA GmbH
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 5

VIPA GmbH, Ohmstraße 4, 91074 Herzogenaurach, Germany
Telefax: [phone]
EMail: [email protected]
Contact your local VIPA Customer Service Organization representative if you encounter
problems with the product or have questions regarding the product. If you are unable to
locate a customer service centre, contact VIPA as follows:
VIPA GmbH, Ohmstraße 4, 91074 Herzogenaurach, Germany
Tel.: [phone] (Hotline)
EMail: [email protected]
1.2 About this manual
This manual describes the Touch Panel 62K-NHC0-... from VIPA. It contains a description
of the structure, project engineering and deployment.
Product Order number as of state:
HW BS
TP 610LC 62K-NHC0-DH 01 WindowsÒ CE 6.0 Core
TP 610LC+ 62K-NHC0-CB 01 WindowsÒ CE 6.0 Prof.
The manual is targeted at users who have a background in automation technology.
The manual consists of chapters. Every chapter provides a self-contained description of a
specific topic.
The following guides are available in the manual:
nAn overall table of contents at the beginning of the manual
nReferences with page numbers
The manual is available in:
nprinted form, on paper
nin electronic form as PDF-file (Adobe Acrobat Reader)
Important passages in the text are highlighted by following icons and headings:
DANGER!
Immediate or likely danger. Personal injury is possible.
Technical support
Objective and contents
Target audience
Structure of the manual
Guide to the document
Availability
Icons Headings
VIPA HMI
General
About this manual
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 6

CAUTION!
Damages to property is likely if these warnings are not heeded.
Supplementary information and useful tips.
1.3 Safety information
The system is constructed and produced for:
ncommunication and process control
ngeneral control and automation tasks
nindustrial applications
noperation within the environmental conditions specified in the technical data
ninstallation into a cubicle
DANGER!
This device is not certified for applications in
–in explosive environments (EX-zone)
The manual must be available to all personnel in the
nproject design department
ninstallation department
ncommissioning
noperation
CAUTION!
The following conditions must be met before using or commis-
sioning the components described in this manual:
– Hardware modifications to the process control system should only be
carried out when the system has been disconnected from power!
–Installation and hardware modifications only by properly trained per-
sonnel.
– The national rules and regulations of the respective country must be
satisfied (installation, safety, EMC ...)
National rules and regulations apply to the disposal of the unit!
Applications conforming
with specifications
Documentation
Disposal
VIPA HMI General
Safety information
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 7

2 Hardware description
2.1 Safety information for users
VIPA modules make use of highly integrated components in MOS-Technology. These
components are extremely sensitive to over-voltages that can occur during electrostatic
discharges. The following symbol is attached to modules that can be destroyed by elec-
trostatic discharges.
The Symbol is located on the module, the module rack or on packing material and it indi-
cates the presence of electrostatic sensitive equipment. It is possible that electrostatic
sensitive equipment is destroyed by energies and voltages that are far less than the
human threshold of perception. These voltages can occur where persons do not dis-
charge themselves before handling electrostatic sensitive modules and they can damage
components thereby, causing the module to become inoperable or unusable. Modules
that have been damaged by electrostatic discharges can fail after a temperature change,
mechanical shock or changes in the electrical load. Only the consequent implementation
of protection devices and meticulous attention to the applicable rules and regulations for
handling the respective equipment can prevent failures of electrostatic sensitive modules.
Modules must be shipped in the original packing material.
When you are conducting measurements on electrostatic sensitive modules you should
take the following precautions:
nFloating instruments must be discharged before use.
nInstruments must be grounded.
Modifying electrostatic sensitive modules you should only use soldering irons with
grounded tips.
CAUTION!
Personnel and instruments should be grounded when working on electro-
static sensitive modules.
2.2 Properties
The VIPA Touch Panel allows you to visualize and alter operating states and recent
process values of a connected PLC. The Touch Panel is a compact and modular
embedded PC based on WindowsÒ CE. Besides the extensive WindowsÒ CE functions
the Touch Panel offers varied communication possibilities. Here the Touch Panel can
simply be configured, controlled and remoted. By including a selectable HMI/SCADA run-
time the Touch Panel is particularly suitable for monitoring and controlling of process
cycles.
Handling of electrostatic
sensitive modules
Shipping of modules
Measurements and altera-
tions on electrostatic sen-
sitive modules
General
VIPA HMI
Hardware description
Properties
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 8

n62K-NHC0-DH
–WindowsÒ CE 6.0 Core
– Movicon 11 CE Basic (512 I/O bytes)
n62K-NHC0-CB
– WindowsÒ CE 6.0 Prof.
– Movicon 11 CE Standard (4096 I/O bytes)
nProzessor Cortex-A8, 1000MHz
nFlash memory 128Mbyte, SDRAM 256Mbyte
nSD card slot
nRS232, RS232/RS422/RS485, USB-A- and 2 Ethernet interfaces
nMPI/PROFIBUS DP interface (optional)
nRobust aluminium case
nDisplay resolution 1024 x 768 / 768 x 1024
nBattery backed clock
nResistive analog touch screen
nEasy mounting via 10 mounting clips
nProtection class IP65 (frontal)
Order data
Type Order number Description
TP 610LC/+ 62K-NHC0-... 10'' TFT color, RS232, RS232/RS422/RS485, USB-A, 2x Ethernet
RJ45
MPI/PROFIBUS DP
interface
961-0MP0 MPI/PROFIBUS DP interface (optional)
VIPA HMI Hardware description
Properties
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 9

2.3 Structure
2.3.1 Overview
1 Slot for SD storage medium
2 "Host"-USB-A interface
3 RJ45 jack for Ethernet communication LAN 1
4 RJ45 jack for Ethernet communication LAN 2
5 RS232 interface COM 1
6 RS232/RS422/RS485 interface COM 2
7 MPI/PROFIBUS DP interface COM 3 (optional)
8 Slot for DC 24V voltage supply
9 Display with touch sensitive area (touch screen)
Front view
VIPA HMI
Hardware description
Structure > Overview
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 10

1 Slot for SD storage medium
2 "Host"-USB-A interface
3 RJ45 jack for Ethernet communication LAN 1
4 RJ45 jack for Ethernet communication LAN 2
Please note that these two Ethernet interfaces cannot be used as a
Switch!
1 RS232 interface COM 1
2 RS232/RS422/RS485 interface COM 2
3 MPI/PROFIBUS DP interface COM 3 (optional)
4 Slot for DC 24V voltage supply
Please make sure that the Touch Panel always has to be supplied with
external voltage!
Side view
Bottom view
VIPA HMI Hardware description
Structure > Overview
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 11

2.3.2 Interfaces
VIPA HMI
Hardware description
Structure > Interfaces
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 12

25 pin SubD femaleRS232/RS422/RS485 inter-
face
VIPA HMI Hardware description
Structure > Interfaces
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 13

9 pin SubD plug
nInterface is compatible to the COM interface of a PC
nLogical signals as voltage levels
nPoint-to-point links with serial full-duplex transfer in two-wire technology up to 15m
distance
nData transfer rate up to 115.2kbit/s
9 pin SubD female
The two RJ45 jacks provide the interface to the twisted pair cable, required for Ethernet.
Please note that these two Ethernet interfaces cannot be used as a
Switch!
Using the "Host"-USB-A interface USB mouse, keyboard, stick or USB hard discs can be
connected.
The Touch Panel has got an integrated power supply. The power supply has to be pro-
vided with DC 24V (20.4 ... 28.8V). For this you find an according DC 24V slot at the
back. The power supply is protected against inverse polarity and overcurrent.
RS232 interface
MPI/PROFIBUS DP inter-
face (optional)
Ethernet connection
"Host"-USB-A
Power supply
VIPA HMI
Hardware description
Structure > Interfaces
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 14

2.3.3 Memory management
The following memory systems are available for every Touch Panel:
n256Mbyte work memory
n128Mbyte Flash disk
nUSB storage media using "Host"-USB-A interface
nSlot for SD
Every Touch Panel has a work memory with a size of 256Mbyte. The work memory is not
buffered and is deleted after shut down. Please regard that also registry entries are
stored in the work memory that are set back to default settings after the next re-boot.
As internal permanent storage medium every Touch Panel has a flash disk with a size of
128Mbyte. After the start of WindowsÒ CE this memory is listed as Flashdisk at My
Device.
The connection of USB sticks and USB drives by use of the "Host"-USB-A interface is
supported by the Touch Panel. After connection the storage media is listed as Hard Disk
at My Device.
At the back of the Touch Panel there are the card slots for memory cards. At this slot you
may plug storage modules of the type SD. The card may be plugged and removed during
runtime and is immediately listed as SDMMC Card at My Device.
2.4 Dimensions
For the installation of the Touch Panel in control cabinets and desks the following dimen-
sions are necessary:
Overview
Work memory
Flash disk
USB storage media
Slot for SD
Installation dimensions
VIPA HMI Hardware description
Dimensions
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 15

Front panel width 2.5 ... 6mm
Installation cutting (B x H) 311 x 249mm
Front panel (B x H) 325 x 263mm
Rear panel (B x H x T) 310 x 248 x 50mm
Installation depth 50mm
The degrees of protection are only guaranteed when the following is
observed:
–Material thickness at the mounting cut-out: 2.5 ... 6mm
–The deviation from the plane for the panel cut-out is
£ 0.5mm.
–Permissible surface roughness in the area of the seal:
£ 120µm (fric-
tion coefficient 120)
10" - 62K-NHC0-...
VIPA HMI
Hardware description
Dimensions
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 16

2.5 General data
Conformity and approval
Conformity
CE 2014/35/EU Low-voltage directive
2014/30/EU EMC directive
Approval
UL See Technical Data
others
RoHS 2011/65/EU Restriction of the use of certain hazardous substances in
electrical and electronic equipment
Protection of persons and device protection
Type of protection - IP20
Electrical isolation
to the field bus - electrically isolated
to the process level - electrically isolated
Insulation resistance -
Insulation voltage to reference earth
Inputs / outputs - AC / DC 50V, test voltage AC 500V
Protective measures - against short circuit
Environmental conditions to EN 61131-2
Climatic
Storage / transport EN 60068-2-14 -20…+60°C
Operation
Horizontal installation EN 61131-2 0…+50°C
Vertical installation EN 61131-2 0…+50°C
Air humidity EN 60068-2-30 RH1 (without condensation, rel. humidity 10…95%)
Pollution EN 61131-2 Degree of pollution 2
Mechanical
Oscillation EN 60068-2-6 1g, 9Hz ... 150Hz
Shock EN 60068-2-27 15g, 11ms
Mounting conditions
Mounting place - In the control cabinet
Mounting position - Horizontal and vertical
VIPA HMI Hardware description
General data
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 17

EMC Standard Comment
Emitted interference EN 61000-6-4 Class A (Industrial area)
Noise immunity
zone B
EN 61000-6-2 Industrial area
EN 61000-4-2 ESD
8kV at air discharge (degree of severity 3),
4kV at contact discharge (degree of severity 2)
EN 61000-4-3 HF field immunity (casing)
80MHz … 1000MHz, 10V/m, 80% AM (1kHz)
1.4GHz ... 2.0GHz, 3V/m, 80% AM (1kHz)
2GHz ... 2.7GHz, 1V/m, 80% AM (1kHz)
EN 61000-4-6 HF conducted
150kHz … 80MHz, 10V, 80% AM (1kHz)
EN 61000-4-4 Burst, degree of severity 3
EN 61000-4-5 Surge, degree of severity 3 *
*) Due to the high-energetic single pulses with Surge an appropriate external protective circuit with lightning protection elements like conductors for lightning and overvoltage is
necessary.
2.6 Technical data
2.6.1 62K-NHC0-DH
Order no. 62K-NHC0-DH
Type Touch Panel TP 610LC
Display
Display size (diagonal) 10 "
Display size (width) 203 mm
Display size (height) 152 mm
Resolution 768 x 1024 / 1024 x 768
Aspect ratio 4:3
Type of display TFT color (64K colors)
MTBF Backlights (25°C) 50000 h
System properties
Processor Cortex-A8 1000 MHz
Operating system Windows CE 6.0 Core
User software Movicon 11 CE Basic
Work memory 256 MB
User memory 128 MB
Available memory (user data) 40 MB
SD/MMC Slot ü
VIPA HMI
Hardware description
Technical data > 62K-NHC0-DH
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 18

Order no. 62K-NHC0-DH
CF Card Slot Typ II -
Time
Real-time clock buffered ü
Clock buffered period (min.) 26 w
Type of buffering Manganese Rechargeable Lithium Battery
Load time for 50% buffering period 5 h
Load time for 100% buffering period 24 h
Accuracy (max. deviation per day) 2 s
Operating controls
Touchscreen resistive
Keyboard external via USB
Mouse external via USB
Interfaces
MPI, PROFIBUS-DP optional
MPI, PROFIBUS-DP connector -
Serial, COM1 RS232
COM1 connector Sub-D, 9-pin, male
Serial, COM2 RS232 / RS422 / RS485
COM2 connector Sub-D, 25-pin, female
Number of USB-A interfaces 1
USB-A connector USB-A (host)
Number of USB-B interfaces -
USB-B connector -
Number of ethernet interfaces 2
Ethernet Ethernet 10/100 MBit
Ethernet connector RJ45
Integrated ethernet switch -
Technical data power supply
Power supply (rated value) DC 24 V
Power supply (permitted range) DC 20.4...28.8 V
Reverse polarity protection ü
Current consumption (no-load operation) 0.24 A
Current consumption (rated value) 1.36 A
Inrush current 85 A
I²t 0.34 A²s
Power loss 15 W
VIPA HMI Hardware description
Technical data > 62K-NHC0-DH
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 19

Order no. 62K-NHC0-DH
Status information, alarms, diagnostics
Supply voltage display none
Mechanical data
Housing / Protection type
Material aluminum, galvanized steel
Mounting mounting clips
Protect type front side IP 65
Protect type back side IP 20
Dimensions
Front panel 325 mm x 263 mm x 6 mm
Rear panel 310 mm x 248 mm x 50 mm
Installation cut-out
Width 311 mm
Height 249 mm
Minimum 2.5 mm
Maximum front panel thickness 6 mm
Weight 3350 g
Environmental conditions
Operating temperature 0 °C to 50 °C
Storage temperature -20 °C to 60 °C
Certifications
UL certification yes
KC certification yes
2.6.2 62K-NHC0-CB
Order no. 62K-NHC0-CB
Type Touch Panel TP 610LC+
Display
Display size (diagonal) 10 "
Display size (width) 203 mm
Display size (height) 152 mm
Resolution 768 x 1024 / 1024 x 768
Aspect ratio 4:3
Type of display TFT color (64K colors)
MTBF Backlights (25°C) 50000 h
VIPA HMI
Hardware description
Technical data > 62K-NHC0-CB
HB160 | TP-ECO | 62K-NHC0 | en | 17-09 20