YLI YM-350W User manual

tested
Germany
EMC
R
Specification
(unit:mm)
Diagram
We create security
Cautions:
A. The screw of the armature plate should not be fixed too tight. Proper elasticity
should be guaranteed for the rubber ring so that the armature plate can adjust itself
to the appropriate position.
B. Check the jumper's position before connecting. Figure out it represents 12VDC
or 24VDC.
!
12/24VDC
12/24VDC
12V/420mA
24V/210mA500kg(1200Lbs)
220Lx63Wx36H
220Lx63Wx36H12V/420mA
24V/210mA500kg(1200Lbs)
YM-500W
YM-500W-S
YM-350W
YM-350W-S
228Lx49Wx29H12V/480mA
24V/240mA350kg(800Lbs)Single Door
12VDC
(24VDCneed order)
228Lx49Wx29H12V/480mA
24V/240mA350kg(800Lbs)
Size(unit:mm)VoltageCurrentHolding Force
ModelDoor
Single Door
Single Door
Single Door
12VDC
(24VDCneed order)
Yes
Signal Output
No
No
Yes
YM-350W/YM-350W-SYM-500W/YM-500W-S
36
13
220
190
60
63
Srew Hole
Wire Hole
Mounting Plate
Armature Plate
Location Pin
Anti-magnetic Pin
Nut
M8X35 Screw
washer Rubber Ring
29
11
228
185
45
47
Srew Hole
Wire Hole
Mounting Plate
Location Pin
Anti-magnetic Pin
Nut
washer Rubber RingArmature Plate
M8X35 Screw
Waterproof Magnetic Lock

We create security
Installation
Drill a hole
Inside: Diameter is 8mm
Outside: Diameter is16mm
Door leaf
Drill holes based on the
marked positions.
Make a combination
based on the picture.
Hollow Metal Door Wooden Door Metal Surface Door
Drill a hole
Inside: Diameter is 8mm
Outside: Diameter is 12.7mm
Inside:Drill a hole
diameter is 8mm folding
the plastic straight pin
36mm
Steps
Fold the plate to 90 .
Close the door first, then
place the upper side of
template on door frame,
while adjust the left side
next to the door leaf.
Template
Door Frame
Door leaf
Template
Door Frame
Door leaf
Template
Mark screw positions of
armature plate and magnetic
lock on door leaf and door
frame respectively.
Setpin
Strike the pin into the
armature plate slightly
(to avoid movement).
Make a combination based
on the picture(add washer
accordingly).The rubber ring
must be added.
Place the rubber ring
between armature plate
and door leaf.
Allen Key
Use Allen key to remove
the mounting plate from
lock body.
Rubber ring
Fix the mounting plate on
the door frame according
to the holes drilled earlier.
Use Allen key to screw
the lock body on the
mounting plate.
After all the appropriate
procedures, the holding
force can be maximized.
Finally, fix the tamper
screw.
Screw door
Wire
Wire
Allen Key
Close the door to test
holding force. The angle
between armature plate
and magnetic lock can
be adjusted by adding
or reducing washers.

We create security
Installation Instruction
Demonstration of UL Bracket
Installation
Demonstration of ZL Bracket
Installation
Demonstration of L Bracket
Installation
Bracket Installation
Demonstration of I Bracket
Installation
Different brackets are available according to different types of doors. For example,
narrow door , frameless glass door and inward opening door.
L Bracket-For outward opening door
When the door frame thickness is less than
42mm, L bracket is needed.
ZL Bracket-For inward opening door
For inward opening door, ZL bracket is
needed.
U Bracket
For the frameless glass door. U bracket
is needed.
I Bracket for armature plate
When the door frame is too thick, I bracket
is needed.
Door Leaf
Frame
Armature Bracket
Frameless
glass door
Outswing door
Inswing door
Door Frame

Circuit Board Diagram
Wire Connection
We create security
Red
Black
White
Yellow
Red
Black
White
Yellow