York Fitness 53085 User manual

February 5, 2014
www.yorkfitness.com
Owner’s Manual
YBR-PC-215 Cycle
Item #53085

www.yorkfitness.com
2
Congratulations on
purchasing your exercise
equipment from
You have chosen a high quality, safe and innovative piece
of equipment as your training partner and we are certain
it will keep you motivated on the way to achieving your
personal tness goals.
Please take the time to read this owner’s manual as it
will help you to get the most out of your new exercise
equipment.
For more information visit www.yorktness.com
CONTENTS
Safety Information 03
Customer Support 04
Assembly Instructions 05
Operational Instructions 10
Troubleshooting 13
Fitness Guide 14
Exploded Drawing 16
Part List 18
Protect the environment by not disposing
of this product or batteries with household
waste. Check your local authority for
recycling advice and facilities.
Table of Contents

www.yorkfitness.comwww.yorkfitness.com
3
Safety Information
Please read this instruction manual before you begin
assembly. Great care has been taken to design these
instructions and following them will help you with quicker
assembly and minimize the risk of injury.
It is important to keep these instructions for future reference.
This list is not exhaustive - You are responsible for your safety!
• Assemble and operate the equipment on a level surface.
• Ensure the equipment is stable before use.
• Always ensure that the equipment has adequate space
on each side.
• Ensure that the seat height is adjusted correctly. You
should be stable and balanced while on the saddle.
• Adjust the seat height to ensure that you have a good
downward pedal stroke without overstretching, don’t
compromise your balance.
• Try to ensure that your back is straight while exercising,
especially for long periods.
• The safety level of this equipment can only be maintained
if it is regularly examined for wear and tear.
• Replace defective components iMMediately and keep
the equipment out of use until it is repaired.
• Use only the adjustment setting as described in the
instructions. Always use the correct adjustment pin/xing.
• Always check that any pins / xings are tight and secure
before use and after adjustment.
• Never leave any adjustment devices projecting from the
equipment at any time.
• Always consult your doctor before undertaking any
exercise program.
• Always wear suitable clothing and footwear. (e.g.
tracksuit / shorts / training shoes)
• Remove all personal jewelry before exercising.
• Ensure you warm-up well before using the equipment
as this will help to prevent muscle strain.
• After eating, allow 1-2 hours before exercising as this
will help to prevent muscle strain.
• Never overload the equipment. (See maximum user weight)
• Never use the equipment in any other manner other
than the ways explained in these instructions and any
wall-chart supplied.
• Injuries to health may result from incorrect form /
technique or excessive training.
• Parents and others in charge of children should be
aware of their responsibility, because the natural play
instinct and the fondness of experimenting of children
can lead to situations and behavior for which the
training equipment is not intended.
• If children are allowed to use the equipment, their
mental and physical development and above all their
temperament should be taken into account. They
should be controlled and instructed in the correct use
of the equipment.
• The equipment is under no circumstances suitable as a
children’s toy.
• Children should not be allowed on or around the
equipment, especially when it is not in use.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
• This product is not suitable for therapeutic purposes.
• This product has an integrated speed independent
braking system without a constant power mode that is
governed by magnetic resistance.
• This product has been tested for use in a home
environment and is warranted for In Home, personal,
family or household use.
• Due to our continuous policy of product development,
York Fitness reserves the right to change specications
without notice.
CAUTION! The instructions must be followed carefully in
the assembly, use and maintenance of your equipment.
The warranty does not cover damage due to negligence of
the assembly, adjustment and maintenance instructions
described herein.
Maximum user weight: 150kg
Safety Standards
This equipment meets the requirements of the EU’s EMC and
Low Voltage directives (where applicable), EN957 1 & 5 - CLASS
HA. Therefore the equipment carries the following marks:

www.yorkfitness.com
4
Customer Support
Should you require any assistance regarding this product
please gather the following information and then contact us
using the details below:
• Serial No. - This can be found on the sticker below, located as indicated.
• Original purchase date
• Place of purchase
• Information about the place and conditions of use
• Precise description of the issue / defect
Use only on a level surface
Not suitable for therapeutic purpose
Manufacturer: YORK BARBELL
Contact: York Way, Daventry, England, NN11 4YB
Product Name: YBR-PC-215 Cycle
Max User Weight: 150KG
Safety Standards: EN957 Part 1 & 5 - Class HA
Electrical Info: Adaptor 9V, 500mA
SERIAL NO: 53085-
Product’s Name
Serial Number
This product label is an example only, it is not the
real product name and serial number of the item
you have bought.
Underside of the
main body.
IMPORTANT!! - Please retain your sales receipt, York Fitness Customer Care may request proof of
purchase to validate eligibility for warranty service. Warranty cover starts from the date shown on the
proof of purchase.
ENGLAND
The best way to contact us is via the website:
www.yorktness.com
York Barbell UK Ltd.
York Way, Daventry,
England, NN11 4YB
Tel: [phone]
AUSTRALIA
The best way to contact us is via the website:
www.yorktness.com.au
York Fitness Australia
1/2 Swaham Rd, Minto,
PO Box 5130, NSW 2566
Tel: [phone]

www.yorkfitness.comwww.yorkfitness.com
5
Assembly Instructions
Care & Maintenance
• This equipment should not be placed outdoors, in a garage or an outbuilding. Keep the equipment in a dry place
with as little temperature variation as possible.
• We recoMMend placing a mat beneath the equipment to protect both the equipment and your ooring.
• Always place the equipment in a dry environment.
• Use a warm, damp cloth to keep the product clean.
• No wet cleaning of electrical components. Unplug before any care and maintenance.
• The safety level of the equipment can be maintained only if it is regularly examined for damage and wear. This
includes any ropes, pulleys, nuts, bolts, moving parts, bushes, chains, wheels, bearings & connection points etc.
• Ensure that you inspect the product regularly - at least once a week is recoMMended.
• Ensure that all xings are tight before use.
• Always replace damaged / worn components with original parts from the manufacturer.
Prepare your work area - It is important you assemble the product in a clean and uncluttered space.
Work with a friend - We recoMMend assistance with the assembly as some of the components are quite heavy.
Open the carton - Check any warnings on the carton and make sure you have it the right way up.
Unpack the carton - Remove all the aprts and lay them out on the oor.
Make sure you have the following parts
Zx1
Ix1
Jx1
Px1
Cx1
Ax1
Bx1
Nx1
Kx1
Dx1
Lx1
Sx1 Rx1

www.yorkfitness.com
6
Assembly Instructions
BLISTER PACK
1
54
8 x L-9
Allen Bolt (M8*P1.25*20L)
8 x L-8
Regular Washer (Ø8*Ø19*2t)
1 x L-2
Metal Cover
2 x L-4
Regular Washer (Ø7)
1 x L-7
T-Shape Knob (M7*65L)
2 x L-5
Spring Washser (Ø7)
1 x L-11
Box Spanner
1 x L-12
Allen Key
1 x L-10
Screwdriver
1 x L-3
Bushing (Ø12*40mm)
1 x L-6
Allen Bolt (M7*P1.0*30mm)
1 x L-1
Screws (M3*25mm)
I
L-9
L-8
J
L-9 x 8
L-8 x 8
1

www.yorkfitness.comwww.yorkfitness.com
7
N
12
D
P-2
P-1
2
C-2 x 2
C-4 x 2
C-5 x 2
C-6 x 4
3
R
K
C
C-2
C-5
C-6
C-4
Pre-installed screw

www.yorkfitness.com
8
Assembly Instructions
4
L-4 x 2
L-5 x 2
L-3 x 1
L-6 x 1
L-2 x 1
2
1
L-2
L-4
L-5
L-6
L-7
L-3
B
5
L-1 x 1
A-2 x 4
C-2 x 2
C-1
C-2
L-1
B-5
A-1
A-2
C-8
C-3
1
2
3
Pre-installed screw

www.yorkfitness.comwww.yorkfitness.com
9
Final Check
Your exercise cycle is now assembled.
Please make the following nal checks:
• Make sure all screws / bolts are tightened.
• Make sure the equipment is on a at, level surface.
Input Power
Plug in the adaptor to the equipment then the
computer will produce a beep sound and turn
on the computer at the Manual mode.
Input Power
Hand Pulse Sensors
This exercise cycle is tted with 2 hand pulse sensors. To obtain
a pulse reading you must have both your left and right hands on
the sensors at the same time. Do not grip the hand sensors too
tight to give the computer a few seconds to display the reading. Hand Pulse Sensor
Adjusting The Resistance
This exercise cycle features a speed independent braking
(resistance) system. The resistance is controlled by a magnet,
which is moved closer or further away from the ywheel - the
closer the magnet is to the ywheel the higher the resistance.
The magnet is computer controlled, to adjust simply use the UP /
DOWN key on the console. Resistance Level
Adjust the seat
1. Unscrew the hand wheel.
2. Adjust the seat up / down or forward / backward to your liking.
3. Re-screw the hand wheel - make sure it is screwed tightly.
4. The basic rule for getting the seat height right is that as the
pedal reaches its lowest point, the leg is almost straight.
Note: Do not pull the seat out too far - the maximum is indicated
with a piece of tape on the seat post.

www.yorkfitness.com
10
Operational Instructions
Console
KEY FUNCTION DESCRIPTION
MODE • Dial Clockwise (UP) - Increase resistance level.
• Dial Anti-Clockwise (DOWN) - Decrease
resistance level.
• Dial - Setting selection.
• MODE - Conrm setting or selection.
• During workout, press MODE to lock current
SCAN function.
RESET • Press the RESET button once to go back to
main menu during setup.
• Press and hold the RESET button for 2 seconds
to reboot computer and start from default
setting.
START / STOP • Start / Stop a workout program.
RECOVERY • Test your heart rate recovery. (See the
“Recovery Mode” section)
BODY FAT • Test your body fat % and BMI. (See the “Body
Fat Mode” section)
START / STOPBODY FAT
RESET RECOVERY
MODE
-
+
DISPLAY DESCRIPTION
TIME • Display the workout time during exercise.
• Range 0:00 ~ 99:59
SPEED • Display the workout speed during exercise.
• Range 0.0 ~ 99.9
DISTANCE • Display the workout distance travelled during exercise.
• Range 0.0 ~ 99.9
CALORIES • Display the calories burnt during exercise.
• Range 0 ~ 999
PULSE • Display the user pulse (bpm) during exercise.
• An alarm will sound if your pulse is over the preset target.
RPM • Display the rotation per minute during exercise.
• Range 0 ~ 999
WAT T • Display the power consumption during exercise.
• In Watt Program mode, computer will remain preset watt value during exercise. (Setting
range 0~350)
MANUAL • Display the manual mode workout.
PROGRAM • Display the preset resistance level prole of the selected program mode.
USER • Display the user resistance level prole during a user mode workout.
H.R.C. • Display the H.R.C. mode workout.

www.yorkfitness.comwww.yorkfitness.com
11
Power On
Plug in power supply and the computer will power on and display all segments for 2 seconds.
After power on the monitor for the rst time, the user will be prompted to enter his / her age, sex, height and weight. Use
the UP / DOWN buttons to change the value and press the MODE key to conrm each setting. The monitor will enter the
home screen after the setup.
Stand-by Mode: The LCD monitor will enter stand-by mode after 4 minutes of inactivity. Press on any key to wake the monitor.
Manual Mode
User can begin manual mode by pressing the START button in main menu.
1. Use the UP / DOWN dial to select MANUAL and press MODE to conrm.
2. Use the UP / DOWN dial to preset a target TIME, DISTANCE, CALORIES or PULSE.
Press MODE to conrm.
3. Press on the START/STOP button to begin workout. Use the UP / DOWN dial to adjust resistance level during exercise.
4. Press on the START/STOP button to pause. Press RESET to return to the main menu.
Program Mode
1. Use the UP / DOWN dial to select one of the twelve preset programs and press
MODE to conrm.
2. Use the UP / DOWN dial to set a workout time.
3. Press on the START/STOP button to begin workout. Use the UP / DOWN dial to adjust resistance level during exercise.
4. Press on the START/STOP button to pause. Press RESET to return to the main menu.
User Program Mode
1. Use the UP / DOWN dial to select and press MODE to conrm.
2. Use the UP / DOWN dial to set a load level for the rst column and press MODE to select the next column. Repeat this
step for all 8 columns.
3. Press and hold on the MODE button to nish or quit the setup.
4. Use the UP / DOWN dial to set a workout time.
5. Press on the START/STOP button to begin workout. Use the UP / DOWN dial to adjust resistance level during exercise.
6. Press on the START/STOP button to pause. Press RESET to return to the main menu.
H.R.C. Mode
1. Use the UP / DOWN dial to select and press MODE to conrm.
2. Use the UP / DOWN dial to select 55%, 75%, 90% or TAG (Target H.R. - default: 100).
3. Use the UP / DOWN dial to set a workout time.
4. Press on the START/STOP button to begin workout.
5. Press on the START/STOP button to pause. Press RESET to return to the main menu.

www.yorkfitness.com
12
Operational Instructions
WATT Mode
1. Use the UP / DOWN dial to select and press MODE to conrm.
2. Use the UP / DOWN dial to select a WATT target (Default: 120).
3. Use the UP / DOWN dial to set a workout time.
4. Press on the START/STOP button to begin workout. Use the UP / DOWN dial to adjust WATT level.
5. Press on the START/STOP button to pause. Press RESET to return to the main menu.
Recovery Mode
1. User must be holding the hand pulse sensor to
use this feature. When the pulse value is displayed
on the computer, press on the RECOVERY button.
2. Hold on the hand pulse sensor until the TIME display nish
the countdown from 60 seconds.
3. After the countdown ends, the result will be displayed.
1.0 OUTSTANDING
1.0 < 1.9 EXCELLENT
2.0 < 2.9 GOOD
3.0 < 3.9 FAIR
4.0 < 5.9 BELOW AVERAGE
6.0 POOR
Body Fat Mode
1. After your workout, press on the BODY FAT
button and hold on the handgrips.
2. After 8 seconds, the computer will display the
BMI, FAT% and fat symbol.
3. Press on the BODY FAT button again to return
to main menu.
B.M.I (Body Mass Index) Integrated
B.M.I. SCALE LOW LOW / MED MEDIUM MED / HIGH
Range < 20 20-24 24.1 - 26.5 > 26.5
BODY FAT
SYMBOL LOW (—) LOW / MED (+) MEDIUM (p)MED / HIGH (¿)
MALE < 13% 13% - 25.9% 26% - 30% > 30%
FEMALE < 23% 23% - 35.9% 36% - 40% > 40%
Built in Wireless Heart Rate Receiver
This machine is equipped with a built-in receiver for your heart rate monitoring. To get an accurate reading using
these devices, you will need to be within 90cm of the console, and a minimum of 120cm from others using a heart rate
monitoring device.
(Note: The transmitter may uctuate erratically if you are too close to other heart rate monitoring equipment or there is
other electronics near by, such as TV, Radio...)

www.yorkfitness.comwww.yorkfitness.com
13
Troubleshooting
If you have a problem with your exercise equipment, before you do anything else please check that all the cables have
been connected correctly. Loose cables are very common and many problems can be solved by making sure the cables are
properly connected and not damaged.
The following table details the most common problems and how to x them. If you still have a problem after going through
the troubleshooting guide please call your local YORK distributor for advice.
PROBLEM CAUSE CORRECTION
NO DISPLAY
No power Make sure power cord is plugged in properly
System halted Unplug and re-plug the power cord to reset the
system
NO SPEED DISPLAY Wires are damaged or not connected properly Verify all wires are connected properly
Speed sensor is too far from magnet Contact your local YORK distributor
PARTIAL DISPLAY The PA board is not connected properly
Unplug and re-plug the power cord
Verify all wires are connected properly
Disconnect and re-connect all cables
Contact your local YORK distributor
NO PULSE SIGNAL
Wires are damaged or not connected properly Verify all wires are connected properly
Too much hand movement Grip rmly
Palms too wet Dry palms
Hand Pulse Sensor is being gripped too tightly Grip using moderate pressure
User is wearing rings Remove all rings
ERROR CODE: E1 Hands are not hold on tightly on grips during BODY FAT test.
ERROR CODE: E4 Check the user’s age, height, weight gure setting when the test result is out of the range of FAT% 5~50
and BMI 5~50%.
ERROR CODE: E5 Check the cable is well connected or connector broken.
For your own safety, do not open protective casing. If error persist, please contact your local york distributor for advice.
Keep the equipment out of use until it is repaired.
If you are having problems with your heart rate reading, please note that some bres used in clothes eg) polyester, create
static electricity that may prevent a reliable heart rate reading. Mobile phones, TV’s, microwaves and other electrical
appliances that generate an electromagnetic eld may also interfere with heart rate measurement.

www.yorkfitness.com
14
Fitness Guide
Starting and Finishing Your Workout
Begin and end each workout with a Warm Up / Down session - a few minutes of stretching to prevent strains, pulls
and cramps.
Correct Cycling Form
• Sit on the cycle, with your feet on the pedals and inside the pedal straps.
• Ensure that the seat height is adjusted correctly - you should be stable and balanced whilst on the saddle. The basic rule
for getting the seat height right is that as the pedal reaches its lowest point, the leg is almost straight.
• Try to ensure that your back is straight whilst exercising, especially for long periods.
Suggested Stretches
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Hamstring Stretch
Sit with one leg extended.
Bring the sole of the
opposite foot toward you
and rest it against the inner
thigh of your extended leg.
Reach toward your toes
as far as possible. Hold
for 15 counts, then relax.
Repeat 3 times for each
leg. Stretches: Hamstrings,
lower back and groin.
2. Calf/Achilles Stretch
With one leg in front of the
other, reach forward and
place your hands against
a wall. Keep your back leg
straight and your back foot
at on the oor. Bend your
front leg, lean forward and
move your hips toward the
wall. Hold for 15 counts,
then relax. Repeat 3 times
for each leg. To cause
further stretching of the
achilles tendons, bend
your back leg as well.
Stretches: Calves, achilles
tendons and ankles.
3. Quadriceps Stretch
With one hand against a wall
for balance, reach back and
grasp one foot with your
other hand. Bring your heel
as close to your buttocks as
possible. Hold for 15 counts,
then relax. Repeat 3 times
for each leg. Stretches:
Quadriceps and hip muscles.
4. Inner Thigh Stretch
Sit with the soles of your
feet together and your
knees outward. Pull your
feet toward your groin
area as far as possible.
Hold for 15 counts, then
relax. Repeat 3 times.
Stretches: Quadriceps and
hip muscles.

www.yorkfitness.comwww.yorkfitness.com
15
How Long Should I Exercise For?
That really depends on your current level of tness. If you’re just starting out on a new exercise program, you should start
gradually and build up - do not try to do too much too quickly. 30 minutes, 3 times a week should be enough.
Don’t push yourself too hard - you should never feel exhausted during or following exercise.
Heart Rate Training
To get the most out of your new piece of tness equipment and see the best results from your training you should exercise
at the right level of eort, and that means listening to your heart! Working out to a target heart rate means you can direct
your workout to achieve dierent goals:
Good health - For those wishing to improve quality of life and general well being. Your sessions will need to be done at an
intensity of between 50 - 60% of your estimated maximum heart rate, should last about 30 minutes and can be done on
most days of the week.
Weight loss - To see a signicant reduction in body fat, your sessions must be a little more intense - between 60 and 70% of
your estimated maximum heart rate. These sessions can also be performed on most days of the week for up to 30 minutes.
Improving tness levels - These sessions should be performed at 70 - 80% of your estimated maximum heart rate and can
also involve bouts of interval training that would have your heart rate peaking for short times near your maximum heart
rate level. These are intense sessions and will require at least a 48 hour rest between sessions.
Calculating Your Target Heart Rate
First, you need to nd your estimated maximum heart rate using the formula “220 minus your age in years”. So, if you are 35
years old your estimated maximum heart rate is:
220 - 35 = 185 beats per minute (bpm)
Next, to calculate your target heart rate, simply multiply your estimated maximum heart rate (185bpm) by the applicable
percentage. So, if your goal is better health:
185 x 60% = 111bpm
NOTE: The important issue to remember with all estimated calculations is that they are just estimates
- if you do not feel comfortable exercising at your target then reduce levels to a more tolerable and
comfortable setting for your exercise activities.
Heart rate training requires you to monitor your heart rate throughout the workout. For this we
recoMMend using a chest strap (if your machine has a wireless receiver) or a heart rate monitor. For
more information please get in touch using the Contact Us details.
Always consult your doctor before undertaking a new exercise regime. If you experience nausea,
dizziness or other abnormal symptoms during exercise, stop at once and consult your doctor.

www.yorkfitness.com
16
Exploded Drawing
A-1
A-2
C-1
B-5
C-2
C-8
B
C-3
L-2
L-4
L-5
L-6
L-7
N
L-3
C-2
K
D
C-6
C-5
C-3
C-4
I
P-1
L-9
L-8
P-2
JS
L-1

www.yorkfitness.comwww.yorkfitness.com
17
A-1
B-2
B-4
B-5
B-3
C-1
C-2
C-8
C-7
C-3
C-4
C-5 C-6
B-6
B-1
H-1 H-3 H-5 H-6
H-7 H-9
H-11
I-1
I-2
I-3
I-4 I-5 I-6 I-7
Q-1
Q-2 Q-3 Q-4 Q-5
Q-6 Q-7
Q-8
Q-9
N
I-8
H-12
H-10
H-2 H-4
H-8
J-1 J-2 J-3 J-4 J-5
A-2
D-1 E-12
E-10
E-8
E-6
E-9
K
P-1
R
P-2
E-7
E-11
E-2
E-3
E-4
E-5
D-2
D-3
D-4
D-5
D-6
F-1 F-2
F-3
F-4 F-5
F-6 F-7 F-8
G-2 G-1 G-8
G-7
G-6
G-5
E-1
G-4
G-3
M-4
M-7
M-1 M-6 M-3 M-2
SM-5
A B
D E
C
K
F G P
R
H I Q
N
JLM

www.yorkfitness.com
18
Part List
YORK REF. REF. DESCRIPTION QT Y.
53085-001 AConsole set 1
53085-002 A-1 Console (SM7695-71) 1
53085-003 A-2 Screw (M5x10l) 4
53085-004 BHandlebar set 1
53085-005 B-1 Handlebar 1
53085-006 B-2 Foam grip (530xφ20x5MM str) 2
53085-007 B-3 Hand pulse sensor (Black*2) 2
53085-008 B-4 End cap (Ø7/8") 2
53085-009 B-5 Hand pulse sensor wire (650MM,650MM) 1
53085-010 B-6 Screw (M4x20L) 2
53085-011 CHandlebar post set 1
53085-012 C-1 Decorating cover, left 1
53085-013 C-2 Screw (M5xP0.8X20Lt) 4
53085-014 C-3 Console cable, upper 1
53085-015 C-4 Semi-circuit washer (Ø8xØ19x2T) 2
53085-016 C-5 Flat washer (Ø8xØ19x2T) 2
53085-017 C-6 Hexagon head screw (M8*P1.25*16L) 4
53085-018 C-7 Handlebar post 1
53085-019 C-8 Decorating cover, right 1
53085-020 DSeat adjustable tube set 1
53085-021 D-1 Seat adjustable tube (Black) 1
53085-022 D-2 Fixing screw bracket (7/16"-14) 1
53085-023 D-3 End cap (20*40 Black) 2
53085-024 D-4 Flat washer (Ø14.3XØ25x2.0T) 1
53085-025 D-5 Seat locking knob (7/16"x20l Black) 1
53085-026 D-6 Seat post (Black) 1
53085-027 EFrame set 1
53085-028 E-2 Screw (M4x10L) 1
53085-029 E-3 Speed sensor+wire (400MM) 1
53085-030 E-4 Sensor holder (blue pe) 1
53085-031 E-5 Frame (black) 1
53085-032 E-6 Ring (Ø40) 2
53085-033 E-7 Bearing 6203 (RS) 2
53085-034 E-8 Curve washer (Ø17.5XØ25x0.3T) 1
53085-035 E-9 Flat washer (Ø17.5XØ25x0.3T) 1
53085-036 E-10 C-clip (Ø17) 1
53085-037 E-11 Locking knob (707a M16xP1.5X22L) 1
53085-038 E-12 Post sleeve 1
53085-039 FAxle set 1
53085-040 F-1 Crank, left (6.5") 1
53085-041 F-2 Screw (M8xP1.25X12Lx5t) 3
53085-042 F-3 Axle (Ø17 170L) 1
53085-043 F-4 Drive pully (Ø240x6-groove) 1
53085-044 F-5 Bushing (Ø22xØ17x7.5MML) 1
53085-045 F-6 Drive belt J6 1092M/M) 1
53085-046 F-7 Crank, right (6.5") 1
53085-047 F-8 Screw (M8xP1.0X20L) 2
53085-048 GServomotor and Mag. brake system 1
53085-049 E-1 Console cable, lower (950MM) 1
53085-050 G-1 Servomotor (Cable 950L) 1
53085-051 G-2 Nut (M6) 2
53085-052 G-3 Screw (M8*22L) 1
53085-053 G-4 Eyebolt (M6*Ø18*63L) 1
53085-054 G-5 Flat washer (Ø6xØ13x1T) 2
53085-055 G-6 Spring washer (Ø6) 2
53085-056 G-7 Screw (M6xP1.0*16L) 2
53085-057 G-8 Magnetic brake set 1
53085-058 HFlywheel set 1
53085-059 H-1 Star washer (Ø10xØ17x1T) 2
53085-060 H-2 Nut (3/8"-26x4.5T) 5
53085-061 H-3 Bushing (Ø10xØ14x3MML) 1
53085-062 H-4 Bearing (6900RS) 1
YORK REF. REF. DESCRIPTION QT Y.
53085-063 H-5 Pulley (J8xØ30) 1
53085-064 H-6 Flywheel (Ø280*32W) 1
53085-065 H-7 Bearing (6003RS) 1
53085-066 H-8 Bearing 1
53085-067 H-9 Flat washer (Ø30xØ34x1T) 1
53085-068 H-10 Bearing (6203) 1
53085-069 H-11 Bushing (Ø10xØ14x6MML) 1
53085-070 H-12 Flwheel axle (Ø11.5X120L) 1
53085-071 IFront stabilizer set 1
53085-072 I-1 Front tube endcap(L) 1
53085-073 I-2 Front stabilizer 1
53085-074 I-3 Screw (M8xP1.25X40L) 2
53085-075 I-4 Transportation wheel (Ø57xØ8x20) 2
53085-076 I-5 Nut (M8 30#) 2
53085-077 I-6 Flat washer (Ø8xØ16x1T) 2
53085-078 I-7 Front tube endcap(R) 1
53085-079 I-8 Screw (3/16”#10 x 3/4”) 4
53085-080 JRear stabilizer set 1
53085-081 J-1 Screw (3/16”x3/4”) 4
53085-082 J-2 Rear tube endcap(l) 1
53085-083 J-3 Adjustable pad (3/8"x30L) 2
53085-084 J-4 Rear stabilizer 1
53085-085 J-5 Rear tube endcap(R) 1
53085-086 KBottle holder (Black nylon) 1
53085-087 LBlisterpack 1
53085-088 L-1 Screw (M3x25L) 1
53085-089 L-2 Metal cover 1
53085-090 L-3 Bushing (Ø7xØ12x40MML) 1
53085-091 L-4 Flat washer (Ø7xØ12x1T) 2
53085-092 L-5 Spring washer (Ø7x2T) 2
53085-093 L-6 Screw (M7xP1.0X30L) 2
53085-094 L-7 T-type locking knob (M7xP1.0X65L) 1
53085-095 L-8 Flat washer (Ø8xØ19x2T) 8
53085-096 L-9 Hexagon head screw (M8xP1.25X20L) 8
53085-097 L-10 Screw driver (13.15 Cross) 1
53085-098 L-11 Box spanner (13.14 Cross) 1
53085-099 L-12 Allen key (6MM 30MMLx84MML) 1
53085-100 MSide cover set 1
53085-101 M-1 Screw (M4x50L) 6
53085-102 M-3 Screw (M5x16) 6
53085-103 M-2 Left side cover 1
53085-104 M-4 Right side cover 1
53085-105 M-6 Front left cover 1
53085-106 M-7 Front right cover 1
53085-107 NSeat (LS-A12) 1
53085-108 PPedal, pair (J028 9/16" ) 1
53085-109 P-1 Pedal (L) 1
53085-110 P-2 Pedal (R) 1
53085-111 QBelt tightener set (Black) 1
53085-112 Q-1 Screw (m6xp1.0X12l) 1
53085-113 Q-2 Pulley wheel (Ø20xØ37x20.5MML) 1
53085-114 Q-3 Curve washer (Ø10.5XØ15x0.3T) 2
53085-115 Q-4 Belt tightener 1
53085-116 Q-5 Nut (M8) 1
53085-117 Q-6 Flat washer (Ø6xØ12x1T) 1
53085-118 Q-7 Screw (M8xP1.25X20L) 1
53085-119 Q-8 Flat washer (Ø8*φ19*2T) 1
53085-120 Q-9 Spring (ODφ16xφ2.0X35T) 1
53085-121 RFront post cover 1
53085-122 STransformer (9vdc 500ma) 1
53085-123 M-5 Dc wire (500MM) 1

www.yorkfitness.comwww.yorkfitness.com
19
Notes

www.yorkfitness.com