Yoshimura 070BG131001 User manual

RESEARCH&DEVELOPMENT OF AMERICA, INC.
www.yoshimura-rd.com
FENDER ELIMINATOR KIT
070BG131001
Yamaha FZ-10
5420 DANIELS STREET STE A, CHINO CA., 91710 · [phone] · [phone] · FAX [phone]
THIS PRODUCT IS NOT DOT APPROVED.
Yoshimura R&D of America, Inc. is not liable or responsible for any resulting event caused by the
installation of this product. Check with local laws and regulations for compliance prior to
installation and use. This product is not intended for use on public highways.
! !

No.
Item
Description
Qty.
1
13100-FEBKT
Fender Eliminator Bracket
1
2
12200-FEBKT
License Plate bracket
1
3
070BG-LH-K1
LED License Plate Light
1
4
070BG-LPF
License Plate Frame
1
5
13630-TSBL-00
Left Turn Signal Bracket
1
6
13630-TSBR-00
Right Turn Signal Bracket
1
7
M4X6BHS
4mm x 6mm Button Head Screw
2
8
M6X10BHS
6mm x 10mm Button Head Screw
2
9
M6X14BHS
6mm x 14mm Button Head Screw
2
10
M6X16BHS
6mm x 16mm Button Head Screw
2
11
M6X20BHS
6mm x 20mm Button Head Screw
4
12
6MMWASHER
6mm Washer
4
13
6MMLN
6mm Nylon Lock Nut
4
**
BN-SSS-22-18
Butt Connectors
2
**
ZT-300
Cable Ties
3
**
17029
Yoshimura Sticker Sheet
1
Optional Parts
***
070BGUNVTBKT
Universal Turn Signal Bracket Kit
37
2
*** The Yoshimura Universal Turn Signal Bracket Kit is to be used with aftermarket stud-mounted turn signals and is sold separately.
1
2
4
5
6
8
9
10
11
12
13
Assembly Diagram

1. Remove rider seat.
2. Remove left and right rear side cover as per
Factory Service/Owners Manual.
3. Remove the four bolts securing the seat bracket
plate to the frame.
4. Locate and disconnect the license plate light
and rear turn signal connectors.
5. While supporting the stock fender assembly,
remove the four nuts securing the fender
assembly to the frame.
Note: Take precaution when removing the stock
fender assembly and avoid snagging the
stock license plate light and turn signal
connectors as they will be re-used.
6. Remove the plastic key hole cover from the
stock fender assembly.
Note: Key hole cover will be re-used. Do not
damage during disassembly.
7. Remove left and right turn signals from the
stock fender assembly.
8. Cut the stock license plate light connector wires
on the stock fender assembly side. Be sure to
cut at least a 6” section of wire from the
connector.
Removal
Installation
1. Install (No. 3) 070BG-LH-K1, Yoshimura license
plate light onto (No. 2) 12200-FEBKT,
Yoshimura license plate bracket using (No. 7)
M4X6BHS, 4mm button head screws provided
in the kit.
2. Install (No. 1) 13100-FEBKT, fender eliminator
bracket using (No. 11) M6X20BHS, 6mm button
head screws along with the stock nuts.
2
3
7
3. Install (No. 2) 12200-FEBKT, license plate
bracket onto (No. 1) 13100-FEBKT, fender
eliminator bracket using (No. 8) M6X10BHS,
6mm button head screws as shown in the
diagram below.
8
2
1
3
4. Install the stock plastic key hole cover onto
(No. 1) 13100-FEBKT, fender eliminator
bracket by inserting the key hole cover pins into
holes A and B.
Note: Check fitment and function of plastic key
hole cover. Confirm that the plastic key
hole cover is secure. If required, adjust
13100-FEBKT, fender eliminator bracket
by pinching the two sides and tightening
the four mounting screws.
5. Using the BN-SSS-22-18 butt connectors
provided in the kit, connect the Yoshimura
license plate light wires to the stock license
plate light wires as follows:
Blue w/ Red Stripe -to- Red Wire
Black Wire -to- Black Wire
a) Strip the stock fender light wire ends
1/4” - 1/2” and insert into BN-SSS-22-18,
butt connectors provided in the kit.
b) Center the spliced wire ends in the
middle and using a heatgun or lighter,
apply heat evenly on the outer edges of
the butt connector to shrink and hold
wires in place.
A
B

c) Making sure that the stripped ends are
centered, heat the center of the butt
connector evenly until the solder begins
to liquify.
d) Allow to cool completely and tug both
ends of the wires to verify that connection
is secured.
Scan for link to butt connector instruction video.
6. Install stock left and right turn signals onto
(No. 5,6) 13630-TSBL/R-00, turn signal
brackets.
7. Install (No. 5,6) 13630-TSBL/R-00, turn signal
brackets and (No. 4) 070BG-LPF, license plate
frame using the (No. 9,10) M6X16BHS and
M6X14BHS, 6mm button head screws as
shown below.
8. Route wires between the stock key hole cover
and (No. 1) 13100-FEBKT, fender eliminator
bracket and under the seat.
9. Reconnect left and right turn signal and license
plate light wires.
10. Re-install seat.
11. Check for proper function of license plate light,
turn signals, brake light, and that all brackets
and components are secure prior to riding.
4
4
5
6
13
12
10
9