Young Electric Sole User manual

Parts Parts List
Requied Tools（Not included）
Name Imperial Metric
Monkey Wrench 12’’ 300mm
Open Wrench 7/16’’ 11mm
Open Wrench 11/16’’ 17mm
Part# Description Qty
1 Beam Assembly 1
2 M10 Outer Hexagon Bolt 4
3 Front Wheel Mount 1
4 M10 Long Outer Hexagon Bolt 2
5 M10 Lock Nut 3
6 Bottom Fixing Bracket 1
7 Support Rod 1
8 M10 Low Square Neck Bolt 1
9 Adjustable Support Assembly 1
10 M16 Shockproof Bolt 1
11 φ16 Spring Washer 1
12 φ16 Flat Washer 1
13 φ3.8 Cotter Pin/Lock 1
1
2
x
x
x
3
4
x
x
x
5
x
x
x
8
x
x
x
6
x
x
x
7
x
x
x
9
x
x
x
1
0
1
0
1
0
1
0
10
11
12
13

STEP1
Put the holes of Front Wheel Mount (3) and Beam Assembly (1)
aligned, install 4pcs-M10 Outer Hexagon Bolt (2) and tighten
them.
STEP2
Place the components assembled in steps 1 above into the
bottom fixing bracket assembly (6), align the holes, install 2pc
Long Outer Hexagon Bolt (4) and 2pc M10 Lock Nut (5), and
tighten the bolts.

STEP3
Insert the Support Rod (7) into the Bottom Fixing Bracket (6),
align the holes, install M10 Low Square Neck Bolt (8) and M10
Lock Nut (5), and tighten them until the support rod does not
move.
STEP4
Insert Adjustable Support Assembly (9) into the Support Rod (7),
and properly tighten the knob so that it does not slide down.
50Nm

STEP5
Align the holes of the folding tube with the holes on the vehicle's
2" hitch receiver, then connect the two parts as shown below.
Place an M16 shockproof bolt (10), through the φ16 Spring
Washer (11), φ16 Flat Washer (12) and the aligned holes. Secure
the bolt in place with the φ3.8 Cotter Pin/Lock (13) making sure
to place the pin through.
The diameter of lock beam
should be less than 7mm.
The lock is not included.
2"

Bike Installation Instructions
Before placing the bicycle, stand up the support rod in the middle, snap the front tire of the ebike into the fixed frame, place the
rear tire in the beam, and then use the ratchet wheel straps to fix the front wheel, rear wheel, and seat tube of the bicycle as shown in the
figure below.
Note: Use the ratchet wheel strap
to fix and tighten the seat tube or
horizontal tube of the bicycle.
Note: Use the ratchet wheel strap
to fix and tighten the front wheel of
the bicycle.
Note: The rear tire fixing seat needs
to be placed in front of the rear
wheel.

How to Adjust the Wheel Cradle
1.Pull the cam gear
5.Turn it tighten by clockwise
3.Slide it
4.Until it against the tire
2.Turn in counterclockwise
6.Press it down

YOU ARE
ALMOST
THERE!

Dimension Technical Specifications
Maximum weight bicycle capacity 100LBS
Maximum bicycle wheelbase 50''
Applicable Hitched Bike Types: Electric Bike/Regular Bike
Not intended for use with mopeds, motorcycles or 3
wheels bikes
Universal sized up to 5'' wide tire
Model Name YOUNG ELECTRIC Sole
Description 2'' Hitch 1-Bike Rack
Material Aluminum & Steel
Maximum Weight Capacity 100lbs
Applicable Vehicles Vehicles with 2'' receiver
Package Size 55.9x13.9x8.3in
Package Weight 37.8lbs

Do not overload beyond the bike rack’s weight capacity of 100lbs.
Do not carry more than 1 bike on the carrier.
The bike rack is not intended for transporting humans or animals.
If you are planning to load only one bike, it is recommended to place it in the position closest to the vehicle.
All bikes must be secured properly before operating the vehicle.
Make sure the front of the bike(s), when mounted, is at or above the bottom of the bumper to avoid damage to the bike(s).
Do not carry flammable items on the bike rack.
If using the bike rack to transport electric bicycles, please remove the batteries from the bicycles prior to transporting them. This will
help reduce the weight supported by the carrier.
During long trips, frequently check the straps and bike position, especially if traveling on rough terrain.
Please do not make alterations to the product, as it can pose potential hazards to your safety.
Failure to heed these warnings may result in personal injury and/or property damage.
To prevent serious injury or death, inspect the bike rack for any signs of wear, corrosion and fatigue before each use. Do not use the
bicycle rack if parts are bent, broken, deformed or missing. If parts are bent, broken, damaged or missing, remove the rack from your
vehicle before operating the vehicle.
⚠WARNINGS ⚠

Young Electric Warranty Policy
Young Electric is committed to providing our customers with a
quality shopping experience, for the products we sell, we provide
a 2-year warranty from the date of purchase, which includes
non-artificial product defects. This warranty does not cover
issues caused by normal wear and tear including (but not limited
to) weather, scratches, dents, rust, accidents, unlawful vehicle
operation, misuse, abuse, neglect, theft, unauthorized
modifications, or unauthorized repair.
No warranty is provided for defects caused by improper fit,
improper vehicle installation, installation on an "unsuitable"
vehicle, incorrect installation of the bike on the rack, or
overloading of the weight limit of the rack. This warranty
terminates if the purchaser transfers the product to any other
person.
If a product is believed to be defective, the purchaser should
directly contact Young Electric Team at 888-933-8899 or through
[e-mail]
Disclaimer of Liability: Repair or replacement of a defective
product or the issuance of a refund or credit (as determined by
Young Electric) is a purchaser’s exclusive remedy under this
warranty.
Young Electric shall not be liable for any direct, indirect,
consequential, incidental, special, punitive or any other damages
in connection with the purchase, use or handling of this product.
Some states do not allow the exclusion or limitation of
consequential or incidental damages, and the above limitation
may not apply to you. This Limited Warranty gives you specific
legal rights, and you may have other rights that vary from state to
state.

THANK YOU FOR CHOOSING A
YOUNG ELECTRIC HITCH BIKE RACK!
YOUNG ELECTRIC Bike racks are designed to make your bicycles
well hitched with stability & safety. Carefully read this Owner’s
Manual before assembly, it will give you all the information
necessary for assembly and adjusting.
YOUNG ELECTRIC works hard to guarantee you a bike rack that
is properly assembled and correctly adjusted when it leaves our
factory. Please contact our Help Center if you still have any
questions after reading this manual. Our customer service staffs
are ready to answer questions regarding assembly, performance,
operation, service parts or other general services.
Email: [e-mail]
Keep this Owner’s Manual in a safe place for future reference. All
content in this manual is subject to change as we continually
work to refine our products.
This manual contains warnings, cautions, and notes, therefore
please carefully read all of this information for your safety.Give
special attention to any information that has a warning or
caution symbol before or next to it. Also, pay attention to any
information preceded by NOTICE as this will be important
information that may be related to safety.
Always properly maintain and care for your bike rack so original
quality and safety are retained.

Get Support
https://youngelectricbikes.com
[e-mail]
Toll Free Number: 888-933-8899