Youshiko YC8060 Manual

Youshiko YC8060 Radio control Digital Clock Analog Style
Initial set up:
Install the batteries in the clock and then leave it, Keep it well away
from other electronics devices nearby to avoid any interference , Radio
control signal can or may take time, depends on the location in UK, but
will pick up the signal within few minutes to few hours ( Max within
next 24h ), Clock will set UK time itself and then You don't have to do
anything ever.
1.1 Time - Alarm snooze function
- Perpetual Calendar Up to Year 2099
1.2 Temperature - Indoor measurable range: -9.9 °C ~ +50 °C
- Measures °C / °F user selectable
2. Unit Appearance
Part A-LCD
A1: Hour
A2: Minute
A3: Second
A4: Radio Controlled Icon
A5: Date
A6: Day of Week
A7: Temperature
1

Part B-Button
B1: “MODE/SET”Button
B2: “▼/SEC” Button
B3: “▲/ (DM)”Button
B4: “AL ON/OFF” button
B5: “ALARM MODE”Slide key
B6: “SNOOZE”Button
Part C-Structure
C1: Hanging Hole
C2: Battery Door
C3: Stand
3. Getting Started:
Open battery Cover (C1)
Insert 4 x AA size batteries observing polarity [“ +” and “ –“ marks]
Replace battery compartment cover
Place the unit onto flat surface, or wall mounted by the hanging hole; the unit is
ready for use now.
4. Time and Alarm Setting
4.1 Radio Controlled Time:
After batteries inserted, the clock automatically starts to scan the MSF time
signal.
Radio Control Icon“ ” flashes on the LCD.
(A4) flashes，
Indicating now is receiving
DCF signal
(A4) turns on,
Indicating signal received
successfully
(A4) disappear,
Indicating signal reception
failed
The clock automatically synchronized with the MSF radio signal every day at 2:00
& 3:00 a.m. to maintain accurate time keeping. If synchronization with the MSF
radio signal fails, “ ” on LCD disappear and the clock.
The clock can be set to scan the radio signal manually by holding “▼” button for
3 seconds. Each reception takes several minutes.
Stop scanning MSF radio signal by holding “▼”button for 3 seconds
“DST” shown on the LCD if it is in daylight saving time mode
2

4.2 Manual Time Setting:
In time display, hold “MODE/SET” button for 3 seconds to enter Clock/Calendar
setting Mode.
Press “▲”or “▼”button to adjust the setting and press “MODE/SET” button to
confirm each setting.
(By keeping the “▲”or “▼”button pressed, could accelerate the process and
reach the desired value more quickly)
The setting sequence is shown as follow: RCC ON/OFF, Hour, Minute, Year,
Month/Date Sequence, Month, Date, °C / °F(unit of temperature setting)
Note:
(1) All setting modes will automatically exit in around 15 seconds without any
adjustment
(2) In time display mode, press “▼”button to select the display with or without
second.
(3) In time display mode, press “▲”button to select the month/date sequence, and
the selection would be confirmed in around 5 seconds without any adjustment.
4.3 Alarm Setting:
Press “MODE/SET”button select to view alarm time, “ALARM TIME”display on
the LCD.
When view alarm time, hold “MODE/SET”button for 3 seconds to set alarm time,
press “▲”or “▼”button to adjust the alarm time. Press “MODE/SET” button to
confirm the setting.
4.4 Snooze Alarm Function:
Press “AL ON/OFF”to activate alarm function. Alarm icon “appears on the
display. Press “AL ON/OFF”button again to deactivate alarm function, alarm icon
“ ” disappear from the display.
Slide “ALARM MODE”switch to select the day for alarm function. There are three
options: from Monday to Sunday, from Monday to Saturday, from Monday to
Friday.
Press “SNOOZE”button when alarm alerts. “ ” flashes on the LCD. The alarm
snoozes for around 5 minutes, then it alerts again. The snooze function can be
enabled for maximum 7 times.
3

When alarm alerts, except “SNOOZE”button, press any other buttons to stop the
alarm. Otherwise, the alarm signal sounds for about 2 minutes, then stops
automatically.
5. Thermometer
The temperature measurement range is -9.9°C to +50°C . If the temperature is out
of the measurable range, LL.L (beyond the minimum temperature) or HH.H
(beyond the maximum temperature) will be shown on the LCD.
6. Precautions
The clock loses its time information when the battery is removed.
Do not expose it to direct sunlight, heavy heat, cold, high humidity or wet areas
Never clean the device using abrasive or corrosive materials or products. Abrasive
cleaning agents may scratch plastic parts and corrode electronic circuits
7. Specifications
Unit Dimensions:
210 x 25 x240mm
Battery Requirements:
4 x AA batteries
Temperature range:
-9.9°C to +50°C
Powered By: 4 x AA Batteries ( batteries are not included ) .
Products and batteries:
Products and batteries should not be disposed of with normal household
waste.
According to Directive 2012/19/EU, the device is to be supplied at the
end of its useful life to a proper disposal. The valuable materials
contained in the device are supplied to recycling and avoid the burden of
the environment. Please take this device to a collection point for
electronic waste or a recycling center.
Remove the batteries from the unit before disposing of it and dispose of them
4

separately.
Consumer is legally obliged to dispose of used batteries at a collection point
for used batteries, at a local recycling center or at the battery point of sale, for
further information, contact your local waste disposal company or local
government.
LIABILITY DISCLAIMER:
The electrical and electronic wastes contain hazardous substances; Disposal
of electronic waste in wild country and/or in unauthorized grounds strongly
damages the environment.
• Please contact your local and/or regional authorities to retrieve the addresses
of legal dumping grounds with selective collection.
• All electronic instruments must from now on be recycled. User shall take an
active part in the re-use, recycling and recovery of the electrical and electronic
waste.
•The unrestricted disposal of electronic waste may do harm on public health
and the quality of environment.
•As stated on the gift box and labelled on the product, reading the “User manual”
is highly recommended for the benefit of the user. This product must not be
thrown in general rubbish collection points.
•The manufacturer or supplier cannot accept any responsibility for any incorrect
readings and any consequences that occur should an inaccurate reading take
place.
• This product is designed for use in the home only as indication of the
temperature / Humidity etc
•This product is not to be used for medical purposes or for public information.
• The specifications of this product may change without prior notice.
• This product is not a toy, Keep out of the reach of children.
5

• No part of this manual may be reproduced without written authorization of the
manufacturer.
All enquires: [email protected]
6