Yudor YDS-16LCUD User manual

USER MANUAL
8/16 CHANNELS
DIGITAL VIDEO RECORDER
INSTRUCTION MANUAL
To obtain the best performance and ensure device function correctly, please read this
instruction manual carefully and completely.

2
INSTRUCTION MANUAL
To obtain the best performance and ensure device function correctly, please read this instruction manual
carefully and completely.
FCC Compliance
USER-INSTALLER CAUTION: YOUR AUTHORITY TO OPERATE THIS FCC VERIFIED EQUIPMENT
COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY
THE PARTY RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES.
NOTE: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A
CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE
DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN
THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES,
USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN
ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO
RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL
INTERFERENCE IN WHICH CASE THE USER WILL BE REQUIRED TO CORRECT THE INTERFERENCE
AT HIS OWN EXPENSE.
THIS CLASS A DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN
INTERFERENCE-CAUSING EQUIPMENT REGULATIONS.
WARNINGS, CAUTIONS & COPYRIGHT
WARINGS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of insinuated "dangerous voltage" within the products enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral rhombus is intended to alert the user to the
presence of important operating and maintenance (servicing) instruction in the literature
accompanying the product.
USERS OF THE SYSTEM ARE RESPONSIBLE FOR CHECKING AND COMPLYING WITH ALL FEDERAL,
STATE, AND LOCAL LAWS AND STATUTES COIPCERNING THE MONITORING AND RECORDING OF
VIDEO AND AUDIO SIGNALS. ULTRAK SHALL NOT BE HELD RESPONSIBLE FOR THE USE OF THIS
SYSTEM IN VIOLATION OF CURRENT LAWS AND STATUTES.
COPYRIGHT
THE TRADEMARKS MENTIONED IN THE MANUAL ARE LEGALLY REGISTERED TO THEIR
RESPECTIVE COMPANIES.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION

3
TABLE OF CONTENTS
WARNINGS, CAUTIONS & COPYRIGHT......................................................................... 2
TABLE OF CONTENTS..................................................................................................... 3
1 INTRODUCTION......................................................................................................... 4
1.1 FEATURE........................................................................................................... 4
1.2 SPECIFICATION................................................................................................ 4
2 HARDWARE OVERVIEW........................................................................................... 5
2.1 FRONT PANEL................................................................................................... 5
2.2 BACK PANEL..................................................................................................... 6
3 SYSTEM CONNECTION............................................................................................ 7
3.1 CAMERA & MONITOR LOOPING...................................................................... 7
3.2 EXTERAL ALARM.............................................................................................. 8
3.3 IR REMOTE CONTROL..................................................................................... 9
3.4 RS-232/485 CONTROLLER............................................................................... 10
3.5 PTZ (PAN, TILT AND ZOOM) CAMERA & JOYSTICK CONTROLLER............. 11
3.6 VGA OUTPUT..................................................................................................... 13
3.7 NETWORK......................................................................................................... 13
4 SYSTEM SETUP......................................................................................................... 14
4.1 SETUP MENU DIAGRAM.................................................................................. 14
4.2 LIVE VIEWING................................................................................................... 15
4.3 SYSTEM SETUP................................................................................................ 16
4.4 CAMERA SETUP................................................................................................ 17
4.5 MOTION SETUP................................................................................................ 17
4.6 RECORD SETUP............................................................................................... 18
4.7 ALARM SETUP.................................................................................................. 20
4.8 EVENT LIST....................................................................................................... 21
4.9 HDD MANAGEMENT......................................................................................... 22
4.10 NETWORK SETUP............................................................................................ 23
4.11 FIRMWARE UPDATE......................................................................................... 24
4.12 CDRW BACKUP................................................................................................ 25
4.13 LOAD DEFAULT................................................................................................. 25
5 DVR PLAYBACK & USB BACKUP.............................................................................. 26
5.1 PLAY TIME SEARCH......................................................................................... 26
5.2 EVENT LIST SEARCH....................................................................................... 26
5.3 LIVE VIDEO DURING PLAYBACK..................................................................... 26
5.4 USB BACKUP..................................................................................................... 27
6 BACKUP PLAYBACK.................................................................................................. 28
6.1 MAIN SCREEN SETTING.................................................................................. 28
6.2 CDRW / HDD BACKUP PLAYBACK.................................................................. 29
6.3 USB & LOCAL BACKUP FILE PLAYBACK........................................................ 30
6.4 BACKUP FILE TO AVI........................................................................................ 32
6.5 LOCAL BACKUP................................................................................................ 32
7 NETWORK VIEWING & PLAYBACK…………………………………………………….. 33
7.1 SETUP IP ADDRESS ON PC SITE………………………………………………... 33
7.2 OPTIONAL MICROSOFT INTERNET EXPLORER SETTING…………………. 34
7.3 LOGIN…............................................................................................................. 36
7.4 LIVE VIEWING…............................................................................................... 37
7.5 PLAYBACK…..................................................................................................... 38
7.6 CONFIGURE….................................................................................................. 39
APPENDIX A: RECORDING TIME LAPSE........................................................................ 45
APPENDIX B: POWER COMSUMPTION TABLE.............................................................. 46
APPENDIX C: HDD / USB COMPATIBLE LIST….............................................................. 46
V 2.40 19/MAY/2006
a11633RFMK09

4
1 INTRODUCTION
1.1 FEATURE
zEASY OPERATION, SETTING CAN BE EASILY MODIFIED ON SCREEN DISPLAY.
zMULTI-SPEED RECORDING SELECTION ON NORMAL OR ALARM RECORDING
MODE UP TO 120/100 (NTSC / PAL) PICTURES PRE SECOND.
zSHUTTLE FOR FAST/SLOW VIEWING, JOG DIAL FOR PICTURE BY PICTURE
PLAYBACK.
zBUILD-IN IR & RS-232/485 PORT READY FOR REMOTE CONTROL &
SUB-CONTROL PANELS ADD ON IN THE FUTURE.
zSUPPORT CDRW, USB & NETWORK BACKUP.
1.2 SPECIFICATION
IMAGE SYSTEM NTSC PAL
RESOLUTION-LIVE 720×480 720×576
VIDEO INPUT BNC × 8 / BNC x16
VIDEO LOOPING BNC × 8 / BNC x16
VIDEO OUTPUT BNC × 1
SPOT OUTPUT BNC × 1
AUDIO INPUT RCA × 1
AUDIO OUTPUT RCA × 1
STORAGE MEDIA MAX 2 IDE HARD DISKS ( ONE REMOVABLE )
IMAGE FORMAT M-JPEG
RECORDING RATE 720 x 240 up to 60 PPS
320 x 240 up to 120 PPS
720 x 288 up to 50 PPS
320 x 288 up to 100 PPS
RECORDING MODE MANUAL / ALARM / SCHEDULE
PLAYBACK SPEED FAST FORWARD ×2 ×4 ×6 ×8 ×16 x32
FAST BACKWARD ×2 ×4 ×6 ×8 ×16
PICTURE BY PICTURE PLAYBACK
TITLE 6 CHARACTERS FOR EACH CAMERA
OSD & SETUP TITLE / TIME / DATE / SETUP MENU
ALARM INPUT ×9 / x16 N.O. OR N.C. PROGRAMMABLE
RELAY OUTPUT N.O. OR N.C. PROGRAMMABLE CONTACT ×1
RS-232 & RS-485 PORT YES
PTZ CONTROL YES
ETHERNET YES
IR REMOTE CONTROL YES
BACKUP USB, CDRW & NETWORK
VGA OUTPUT OPTION
PASSWORD CONTROL ONE FOR SYSTEM, ONE FOR HDD FORMAT
KEY LOCK YES
POWER INPUT AC 100-240V INPUT ( 47-63 HZ )
DIMENSIONS MM 430(W) × 91(H) × 380(D)
RACK MOUNTABLE EIA 19” 2U STANDARD MOUNTING RACK

5
2 HARDWARE OVERVIEW
2.1 FRONT PANEL
PLAY
H.D.D
REC
STOP
1
REC
2 3
REW
4
PLAY
56
F.Fwd
Search
87
SELAUTO
COPY
ENTER
MENU
23
22
12111098765
13
Mark ZOOM
Water
2019 21
15 16 17
14 18
3
4
2
1
24
25
PAUSE
POWER
Front Panel of 8-ch DVR
Mark
STOP
REC REW PLAY F.Fwd
Search
PLAY
H.D.D
REC
9 101112
1234
1513 14 16
56 87
SELAUTO
COPY
ENTER
MENU
23
22
12111098765
13 2019 21
15 16 17
14 18
3
4
2
1
24
25
POWER
ZOOM
Water
PAUSE
Front Panel of 16-ch DVR
DVR OPERATION
NO. LABEL OPERATION PTZ
1 POWER Power LED
2 REC Recording LED
3 PLAY Play LED
4 H.D.D H.D.D LED
5 Press REC to start recording. Press again to stop.
6 Press the Rew button to play video backward. Zoom out
7 Press Stop to stop playback
8 Press Pause to pause video playback
9 Press the Play button to play video forward. Zoom in
10
Press F. Fwd to play video forward at high speed.
Press the button again the speed will be change
circulative from ×2,×4,×6,x8,x16 to the highest ×32.
11 Water Mark During playback press Water Mark to enable this mark.
12 ZOOM During live viewing mode support 2x zoom in function.
a11633RFMK09

6
13 1-9 / 1-16 Press the button to display full screen.
14 ▼
Move downward or decrease the number.
Select full/quad formats at 8/16-ch DVR model. Down
15 ◄
Move leftward or decrease the number
Select 8/13 camera formats at 8/16-ch DVR model. Left
16 ▲
Move upward or increase the number.
Select quad/9 camera formats at 8/16-ch DVR model. Up
17 ►
Move rightward or increase the number
Select 9/16 camera formats at 8/16-ch DVR model. Right
18 MENU Press MENU to go into or exit main menu PTZ setup
19 AUTO Press AUTO to switch channel by channel automatically.Auto Scan
20 SEL
Press this button to select the different assembled o
f
camera formats.
Enter or exit
PTZ mode
21 ENTER/
COPY
Press ENTER button to make choose or move curso
r
forward or make confirm in MENU system. / Backup
video or picture to USB or CDRW.
Home
22 CDRW Slot for CDRW.
23 HDD Location of installation for removable HDD.
24 USB connector
25 O IR Sensor for remote control
2.2 BACK PANEL
7654 98 10 11
1214 13
213
Back panel of 8-ch DVR
13 1412
11108 9456 7
31 2
Back panel of 16-ch DVR

7
NO. LABEL OPERATION
1 VGA SETUP DIP Setting Resolution & Frequency
2 VGA D-SUB OUT Connect to CRT or LCD monitor.
3 ETHERNET RJ-45 connector for networking.
4 AUDIO IN Audio input for 1 channel
5 AUDIO OUT Audio output for 1 channel
6 SPOT SPOT Video output
7 MONITOR OUT Video output with BNC & Y/C signal Din connector.
8 ALARM 25 pin D-Sub connector. Alarm input connector.
9 RS-232 / RS-485 9 pin D-Sub connector. For external control of unit.
10 FAN Cooling fan.
11 POWER Power switcher: AC100V~AC240V / 47-63Hz input.
12 Video output Video output with BNC connector.
13 75 ohm Switch between 75 ohm and high resistance.
14 Video input Video input with BNC connector.
3 SYSTEM CONNECTION
3.1 CAMERA & MONITOR LOOPING
75 Ω: If camera looping to other devices or channels and video single are instable,
please switch to this position.
∞: In case of camera input over bright that please switches to this position.
Here recommend link cameras by sequence to avoid unexpected image broken,
from CH1, CH2, CH3, CH4…….

8
3.2 EXTERAL ALARM
There are three types of alarms that the system can be configured to handle. They
are Motion detection Alarm, External Alarm and Video Loss Alarm.
Motion detection Alarm and External Alarm:
When motion detection or External Alarm was triggered, there are 5 possible
actions will be taken.
a. Changes recording speed as alarm recording speed.
b. Monitor will display corresponding full screen alarm channel, it will switch
automatic mode to manual mode if buttons pressing activity occurred in 5 seconds.
c. Relays can be activated by motion detection or external alarm when turning
on.
d. External alarm will be recorded in the event list. Motion detection can be set
to yes or no.
e. The camera title will be transformed into color of yellow when motion is
happening, “ALARM” text will show up when external alarm is triggered.
Video Loss Alarm:
The default setting of Video Loss alarm is enabled and cannot be changed.
Although buzzer action can be disabled, an ALM record will still be added to the
Event List that indicates the precise time of video loss.
25 PIN D-Sub connector is used for external alarm input. It will accept TTL/CMOS
type trigger signals where the 8ch & 16ch DVR alarm inputs will be set by signal
polarity. It also accepts contact type devices. For example, N.O. relay input, the
Alarm Polarity should set to LOW in the ALARM SETUP menu. For N.C. relay
input, the Alarm Polarity should set to HIGH in the ALARM SETUP menu.
Connector pins 1-16 are for TTL/CMOS compatible alarm signals or for connect
one side of the contact type devices. Connector pins 20-21 are for input signal
grounding or the remaining side of the contact type devices.
The alarm hold input accept TTL/COMS alarm signal as well as contract device.
The connector pin 22 connected to Alarm Reset. The Alarm Reset signal return
connects to ground pin (pin 20-21).
Alarm output is Relay Type, Pin 23 is Normal Close and Pin 25 is Normal Open.
These outputs can be used to control external devices.

9
D-SUB25 PIN DEFINE
1-9, (1-16) Alarm 1-Alarm 9 (16) Camera alarm input
10-19, (17-19) N/A
20, 21 GND (connecting to ground)
22 Alarm Reset
23 Alarm output, N.C.
24 Relay COM
25 Alarm output, N.O.
EXAMPLE 1: Connect with PIR (Passive Infrared) device from ALARM1 INPUT.
EXAMPLE 2: A Normal off (Normal Open) alarm siren at Alarm Output.
EX1 EX2
3.3 IR REMOTE CONTROL
ITEM
AUTO Press AUTO to switch channel by channel
automatically.
SEL Press this button to select the different assembled
of camera formats.
.REC Press REC to start recording & again to stop.
1-8/1-16 Press the button to select the channel for full
screen.
Fast backward
Picture by picture backward play
Picture by picture forward play
Fast forward
Play video forward
MODE Change screen format
▲Move upward or increase.
►Move right or increase.
▼Move downward or decrease.
◄Move left or decrease.
To enter item or make choose.
MENU To into or exit main menu
STOP Stop the playback

10
3.4 RS-232/485 CONTROLLER
0 1 0 1 A B A B
D0+ D0- D1+ D1-
Dome Cam 1
CH 1
ID 1
Dome Cam 2
CH 2
ID 2
Dome Cam 3
CH 3
ID 3
RXD TXD
0 1 0 10 1 0 1 A B A BA B A B
D0+ D0- D1+ D1-D0+ D0- D1+ D1-
Dome Cam 1
CH 1
ID 1
Dome Cam 2
CH 2
ID 2
Dome Cam 3
CH 3
ID 3
RXD TXD
Data format
Data: 1 Byte / Parity: None / Start bit: 1 / Baud: 9600
Totally 3 bytes in data frame:
1. Byte=0x10 :Broadcasting DVR
Byte=0x80+ID Number :Remote Control DVR (ID number range: 5~21)
2. Byte=Refer to below table :Command for each key string
3. Byte=First byte plus Second byte :Command for confirm checksum
8-ch DVR 16-ch DVR Command 8-ch DVR 16-ch DVR Command
F.Rew F.Rew 0x38 Rew Rew 0x3a
Picture
Rew
Picture
Rew 0x3b STOP STOP 0x3c
Picture
Fwd
Picture
Fwd 0x3d PLAY PLAY 0x39
F.Fwd F.Fwd 0x3e
0x32 0x31
0x33 0x34
ENTER ENTER 0x35 AUTO AUTO 0x37
SEL SEL 0x36
1 1 0x11 2 2 0x12
3 3 0x13 4 4 0x14
5 5 0x15 6 6 0x16
7 7 0x17 8 8 0x18
9 9 0x19 10 0x1a
11 0x1b 12 0x1c
13 0x1d 14 0x1e
15 0x1f 16 0x30
PIN DEFINE
RS-232 2 RXD
3 TXD
5 GND
RS-485 6 RXDA R+
7 RXDB R-
8 TXDZ T+
9 TXDY T-

11
3.5 PTZ (PAN, TILT AND ZOOM) CAMERA & JOYSTICK CONTROLLER
Following diagram for DVR connect between PTZ camera & joystick controller, for
DVR to control PTZ camera please make sure the CAMERA ID, BANDRATE
(default at 9600 bps) and RS-485 cable, if link with joystick controller please
confirm your DVR ID number. Every DVR ID & the PTZ camera ID behind DVR
must be unique.
0 1 0 10 1 0 1
A B A BA B A B
D+ D- D+ D-D+ D- D+ D-
A B A BA B A B
D0+ D0- D1+ D1-D0+ D0- D1+ D1-
D0+ D0- D1+ D1-D0+ D0- D1+ D1-
A B A BA B A B
R+ R- T+ T-R+ R- T+ T-
R+ R- T+ T-R+ R- T+ T-
DVR 1
ID 1
DVR 2
ID 2
Dome Cam 1
CH 1
ID 1
Dome Cam 2
CH 2
ID 2
Dome Cam 3
CH 3
ID 3
Dome Cam 4
CH 4
ID 4
Dome Cam 1
CH 1
ID 1
Dome Cam 2
CH 2
ID 2
Dome Cam 3
CH 3
ID 3
Dome Cam 4
CH 4
ID 4
DATA+
DATA-
Up to 16CH
D+ D- D+ D-D+ D- D+ D-
Up to 128 ID
Dome Cam 1
ID 1
Dome Cam 2
ID 2
R+ R- T+ T-R+ R- T+ T-
Dome Cam 3
ID 3
Up to 128 ID
Up to 32 ID
Up to 16CH

12
PTZ SETUP & FRONT PLANE CONTROL
EXAMPLE :
A PTZ camera at channel 3 with PELCO-D, 9600bps.
1. Press the channel button 3into full screen mode.
2. Press SEL and “PTZ” mark appear at left upper corner.
3. Press the MENU button into setup mode.
By ▲or ▼to switch item & by ◄or ►to change SPEED/ PROTOCOL &
BAUD RATE.
4. Press the MENU button again back to PTZ control mode.
5. With following label to control PTZ camera.
NO. LABEL PTZ NO. LABEL PTZ
14 ▼Down 5 PLAY Zoom in
15 ◄Left 21 ENTER Home
16 ▲Up 19 AUTO Auto Scan
17 ►Right 6 REW Zoom out
9 MENU PTZ setup 20 SEL Enter or exit
PTZ mode
6. Press the SEL button quite to PTZ control mode.
REC 2005/10/10 MON 12:00:00 50% 120P
PTZ
REC 2005/10/10 MON 12:00:00 50% 120P
PTZ
PTZSETUP
O UP-DOWN SPEED: OOOOO
O LEFT-RIGHT SPEED: OOOOO
O AUTO SCAN SPEED: OOOOO
O PROTOCOL TYPE: PELCO-D
O BAUD RATE: 9600

13
3.6 VGA OUTPUT
VGA output is optional, please ensure that you have proper DVR model for VGA
out put installation. By D-SUB connecter to CRT or LCD monitor, DIP switch
definition & suggestion table as below:
Resolution DIP1 DIP2 Frequency DIP3 DIP4
V G A 6 4 0 × 4 8 0 0 0 56Hz 0 0
SVGA 800×600 0 1 60Hz 0 1
XGA 1024×768 1 0 70Hz 1 0
S X G A 1 2 8 0 × 1 0 2 4 1 1 75Hz 1 1
DIP1 DIP2 DIP3 DIP4 Resolution Frequency Monitor
0 0 0 0
0 0 0 1 60
0 0 1 0 72
0 0 1 1
VGA
640×480
75
15 inch or
below
0 1 0 0 56
0 1 0 1 60
0 1 1 0 72
0 1 1 1
SVGA
800×600
75
15 inch or
below
1 0 0 0
1 0 0 1 60
1 0 1 0 70
1 0 1 1
XGA
1024×768
75
15~17 inch
1 1 0 0
1 1 0 1
1 1 1 0
1 1 1 1
SXGA
1280×1024 60 17 inch or above
3.7 NETWORK
Before starting the network application software, please confirm the RJ-45 cable
has been connected, and then turn the power on.
DVR would check network connection status while DVR power on, thus without
network connection the network function will be disabled.
Please make sure your network environment enabled and RJ-45 cable been
connected, before DVR power up!

14
4 SYSTEM SETUP
4.1 SETUP MENU DIAGRAM
SETUP MODE
․SYSTEM SET [<]
․CAMERA SET [<]
․MOTION SET [<]
․RECORD SET [<]
․ALARM SET [<]
․EVENT LIST [<]
․HDD MANAGEMENT [<]
․NETWORK SET [<]
․FIRMWARE UPDATE [<]
․CDRW BACKUP [<]
․LOAD DEFAULT
․EXIT
NETWORK SETU
P
․IP ADDR: 192.168.001.221
․GATEWAY: 192.168.001.254
․SUB NET: 255.255.255.000
․IP MODE: STATIC IP
․NETWORK ENV: LAN
․NETWORK CHANNEL ENABLE [<]
․HTTP
PORT: 80
․STRAME PORT: 5000
EVENT LIST MASTER PAGE : 001
NO YY/MM/DD HH:MM:SS CH TYPE
01 05/10/10 00:01:00 -- POWER
02 05/10/10 00:02:00 -- RECORD
03 05/10/10 00:03:00 01 V.LOSE
04 05/10/10 00:04:00 02 ALARM
05 05/10/10 00:05:00 03 MOTION
06 05/10/10 00:06:00 -- POWER
07 05/10/10 00:07:00 -- RECORD
08 05/10/10 00:08:00 01 V.LOSE
09 05/10/10 00:09:00 02 ALARM
10 05/10/10 00:10:00 03 MOTION
HDD MANAGEMENT
․OVERWRITE MODE ON
․CAPACITY WARNING 20%
․HDD FORMAT SETUP [<]
․EXIT
DISK CAPACITY LEFT RATIO
MASTER 80GB 41%
SLAVE NONE NONE
FIRMWARE UPDAT
E
FIRMWARE UPDATE START [<]
ALARM SETU
P
BUZZER
․BUZZER/ALARM DWELL 05 SEC
․VIDEO LOSS ALARM ON
․AUDIBLE ALARM ON
․EXT.ALARM MODE N.C
․ALARM DISPLAY MODE DISABLE
․MOTION EVENT OFF
RELAY
․EXT.ALARM RELAY ON
․VIDEO LOSS RELAY ON
․MOTION RELAY ON
․
E
XIT
R
ECORD SETU
P
․SCHEDULE RECORD OFF
․NORMAL RECORD PPS 30P/SEC
․ALARM RECORD PPS 30P/SEC
․ALARM RECORD DWELL 10 SEC
․RECORD QUALITY HIGH
․AUDIO RECORD ON
․EXIT
MOTION SETU
P
․CAMERA CAM 01
․MOTION DETECT ON
․BUZZER OFF
․SENSITIVITY 080
․AREA SETUP [<]
․EXIT
C
AMERA SETU
P
․CAMERA CAM 01
․DISPLAY ON
․RECORD ON
․BRIGHTNESS 50
․CONTRAST 50
․HUE 50
․COLOR 50
․CAMERA TITLE 01
․
E
XIT
S
YSTEM SETU
P
․DATE FORMAT Y-M-D
․DATE 2005/10/10
․TIME H:M:S 00:00:00
․AUTO SWITCH DWELL 02 SEC
․SPOT SETUP [<]
․DATE AND TIME OSD ENABLE
․SYSTEM TYPE NTSC
․KEYBARD LOCK OFF
․ID NUMBER 01
․LANGUAGE SELECT ENGLISH
․PASSWORD MODE DISABLE
․EXIT
CDRW BACKU
P
․START TIME SETUP [<]
START: 2005/10/04 00:00:00
END : 2005/10/04 02:00:00
․BACKUP CD SIZE: 000MB
․CLOSE CD/RW: YES
․ERASE CD/RW: NO
․BA
C
K
U
P
C
DRW
S
TART
[
<
]

15
4.2 LIVE VIEWING
A. Status indicator:
To press ENTER key to switch live display indicator in the live viewing mode.
REC TIME & DATE CHANNEL ID HDD STATUS & PPS
1 O O O O
2 O O O
3 O O
4 O
B. Quick playback search
During live viewing mode and press key into quick time search or event list
search mode.
C. PTZ control:
A. Press the channel key in full screen mode.
B. Press SEL key into PTZ mode, and a yellow PTZ mark at right upper corner.
C. Press MENU key to setup PROTOCOL & BAUDRATE between DVR & PTZ.
D. Press direction key to control the PTZ camera.
E. Press SEL key to exit PTZ mode.
D. Channel AUTO switch
Press AUTO key system would into full screen auto switch mode, and press
AUTO key again back to normal screen.
E. Channel selection
During split channel mode the windows will be limited, thus using the SEL key to
switch others channel on the screen.
F. Zoom
Press ZOOM button to enable zoom in function by direction & enter key to
decide zoom in area, and press enter key again back to normal mode.

16
4.3 SYSTEM SETUP
▲or ▼to change item
◄or ►to change value
A. DATA FORMAT
By ◄or ►to switch Y-M-D, M-D-Y or D-M-Y mode.
B. DATE
By ▲or ▼to switch item & by ◄or ►to change value.
C. TIME
By ▲or ▼to switch item & by ◄or ►to change value.
D. AUTO SWITCH DWELL
By ◄or ►to change volume.
E. SPOT SETUP
Press ENETR into SOPT STEUP mode or MENU to exit,
By ▲or ▼to switch item & by ◄or ►to change value.
F. DATE AND TIME OSD
By ▲or ▼to switch item & by ◄or ►to change value.
G. SYSTEM TYPE
By ◄or ►to change value between NTSC / PAL / EIA / CCIR.
The DVR would switch system type automatically, after press MENU key.
H. KEYBOARD LCOK
By ◄or ►to change value between OFF / TYPE1 / TYPE 2.
TYPE 1: Block all function but channel switch.
TYPE 2: Block all function.
After KEYBOARD LCOK mode setup, please setup the PASSWORD !
If without password, the un-authorized user would access into SYSTEM
SETUP and remove keyboard lock function easily!
I. ID NUMBER
By ◄or ►to change value.
This ID number identifies the DVR location between DVR & remote controller or
joystick controller.
J. LANGUAGE SELECT
By ◄or ►to change OSD language.
K. PASSWORD MODE
By ▲or ▼to switch item & by ◄or ►to change value.
Default password number is "1111".
SYSTEM SETU
P
․DATE FORMAT Y-M-D
․DATE 2005/10/10
․TIME H:M:S 00:00:00
․AUTO SWITCH DWELL 02 SEC
․SPOT SETUP [<]
․DATE AND TIME OSD ENABLE
․SYSTEM TYPE NTSC
․KEYBARD LOCK OFF
․ID NUMBER 01
․LANGUAGE SELECT ENGLISH
․PASSWORD MODE DISABLE
․EXIT

17
4.4 CAMERA SETUP
▲or ▼to change item
◄or ►to change value
A. CAMERA
By ◄or ►to change camera channel.
B. DISPLAY
By ◄or ►to change value for this camera would display on screen or not.
C. RECORD
By ◄or ►to change value for this camera would include with the recording or
not.
D. BRIGHTNESS
By ◄or ►to change brightness level.
E. CONTRAST
By ◄or ►to change contrast level.
F. HUE
By ◄or ►to change HUE level.
G. COLOR
By ◄or ►to change color level.
H. CAMERA TITLE
By ▲or ▼to switch item & by ◄or ►to change wording.
4.5 MOTION SETUP
▲or ▼to change item
◄or ►to change value
A. CAMERA
By ◄or ►to change value for camera motion setup.
B. MOTION DETECT
By ◄or ►to change value for motion detect function.
C. BUZZER
By ◄or ►to change value for buzzer or not while motion detected.
D.SENSITIVITY
By ◄or ►to change sensitivity value from 001 (min) to 100 (max).
E. AREA SETUP
Press ENTER key to enter motion area setting.
1. Press direction key to select which block need to change.
2. Press AUTO to add a line to motion detection.
3. Press SEL to remove a line to motion detection.
4. Press MENU key to quit motion detection area setup.
CAMERA SETU
P
․CAMERA CAM 01
․DISPLAY ON
․RECORD ON
․BRIGHTNESS 50
․CONTRAST 50
․HUE 50
․COLOR 50
․CAMERA TITLE 01
․EXIT
MOTION SETU
P
․CAMERA CAM 01
․MOTION DETECT ON
․BUZZER OFF
․SENSITIVITY 080
․AREA SETUP [<]
․EXIT

18
4.6 RECORD SETUP
▲or ▼to change item
◄or ►to change value
A. SCHEDULE RECORD
By ◄or ►to change value for schedule recording function.
A1.SCHEDULE RECORD SETUP
While SCHEDULE RECORD at ON, press ENTER key into SCHEDULE
RECORD diagram.
▲or ▼to change item
◄or ►to change value
A1.1
WEEKDAY & WEEKEND
The week days separated into 2 area weekday & weekend.
EXAMPLE 1:
If weekday are from Monday to Friday, thus the weekend must be Saturday to
Sunday.
EXAMPLE 2:
If weekday are from Wednesday to Friday, thus the weekend must be Saturday
to Tuesday.
EXAMPLE 3:
If weekday are from Monday to Wednesday, thus the weekend must be
Wednesday to Sunday.
MON TUE WEB THU FRI SAT SUN
EX1 WEEKDAY WEEKEND
EX2 WEEKEND WEEKDAY WEEKEND
EX3 WEEKDAY WEEKEND
RECORD SETU
P
․SCHEDULE RECORD OFF
․NORMAL RECORD PPS 30P/SEC
․ALARM RECORD PPS 30P/SEC
․ALARM RECORD DWELL 10 SEC
․RECORD QUALITY HIGH
․AUDIO RECORD ON
․EXIT
RECORD SETU
P
WEEKDAY: MON-FRI
START-STOP TYPE PPS ALM PPS
01-00 [X] 30P 60P
00-01 [0] 30P 60P
WEEKEND: SAT-SUN
START-STOP TYPE PPS ALM PPS
ALL-TIME [X] 30P 60P
EXIT

19
A1.2
START-STOP
The 24 hours can be ALL TIME & separated hour's mode.
ALL TIME
Using the same recording type & PPS in whole day.
Separated hour's
As like weekday & weekend setting, every 24 hours can be separated 2 areas.
EXAMPLE 1:
Business hours form 8am-16pm, and 16pm-8am off.
EXAMPLE 2:
Business hours form 10am-20pm, and 20pm-10am off.
2 4 8 6 10 12 14 16 18 20 22 24
EX1 OFF BUSINESS HOURS OFF
EX2 OFF BUSINESS HOURS OFF
A1.3
TYPE
By ◄or ►to change recording type mode.
A Alarm recording only.
O Full time recording.
X No recording.
A1.4
PPS
By ◄or ►to change normal recording picture pre second.
A1.5
ALM PPS
By ◄or ►to change alarm recording picture pre second.
NTSC 120 / 60 / 30 / 15 / 10 / 5 / 3 / 2 / 1 PPS.
PAL 100 / 50 / 25 / 12 / 10 / 5 / 3 / 2 / 1 PPS.
Even the camera RECORD been turn off from CAMERA SETUP, during
120/100 PPS mode system would sharing PPS to each channel automatically.
B. NORMAL RECORD PPS
By ◄or ►to change how many picture pre second in normal recording.
C. ALARM RECORD PPS
By ◄or ►to change how many picture pre second in alarm recording.
D. ALARM RECORD DWELL
By ◄or ►to change how many second recording while alarm occurs.
E. RECORD QUALITY
By ◄or ►to change recording quality for LOW / MEDIUM / HIGH / BEST.
F. AUDIO RECORD
By ◄or ►to decide included with audio recording or not.

20
4.7 ALARM SETUP
▲or ▼to change item
◄or ►to change value
BUZZER
A. BUZZER/ALARM DWELL
By ◄or ►to change how many second buzzer while alarm occurs.
B. VIDEO LOSS ALARM
By ◄or ►to change value for video loss alarm.
C. AUDIBLE ALARM
By ◄or ►to change value for audible alarm.
D. EX. ALARM MODE
By ◄or ►to change value for external alarm device.
N.C: For Normal Close device as like infrared detecter.
N.O: For Normal Open device as like alarm siren or etc.
E. ALARM DISPLAY MODE
By ◄or ►to change value for alarm display mode.
F. MOTION EVENT
By ◄or ►to change value for adds the detected motion into event list or not.
RELAY
G. EXT. ALRAM RELAY
By ◄or ►to change value for triggered the relay from external alarm device.
H. VIDEO LOSS REPLAY
By ◄or ►to change value for triggered the relay while video loss occurs.
I. MOTION RELAY
By ◄or ►to change value for triggered the relay if motion been detected.
ALARM SETU
P
BUZZER
․BUZZER/ALARM DWELL 05 SEC
․VIDEO LOSS ALARM ON
․AUDIBLE ALARM ON
․EXT.ALARM MODE N.C
․ALARM DISPLAY MODE DISABLE
․MOTION EVENT OFF
RELAY
․EXT.ALARM RELAY ON
․VIDEO LOSS RELAY ON
․MOTION RELAY ON
․EXIT