Zalip CDE570AM-U User manual

1
ZALiP
CDE570AM-U
WiFi Gigabit Router
User Manual

2
Copyright
The contents of this publication may not be reproduced in any part or as a whole, stored,
transcribed in an information retrieval system, translated into any language, or transmitted
in any form or by any means, mechanical, magnetic, electronic, optical, photocopying,
manual, or otherwise, without the prior written permission.
Trademarks
All products, company, brand names are trademarks or registered trademarks of their
respective companies. They are used for identification purpose only. Specifications are
subject to be changed without prior notice.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against radio interference in a commercial environment. This
equipment can generate, use and radiate radio frequency energy and, if not installed and
used in accordance with the instructions in this manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
interference, in which case the user, at his own expense, will be required to take whatever
measures are necessary to correct the interference.
CE Declaration of Conformity
This equipment complies with the requirements relating to electromagnetic compatibility,
EN 55022/A1 Class B.

3
TABLE OF CONTENTS
COPYRIGHT ......................................................................................................................... 2
FCC INTERFERENCE STATEMENT................................................................................... 2
CHAPTER 1 INTRODUCTION.......................................................................................... 4
1.1PACKAGE LIST ........................................................................................................ 4
1.2 HARDWARE INSTALLATION .................................................................................. 5
CHAPTER 2 GETTING STARTED ................................................................................... 8
2.1 EASY SETUP BY WINDOWS UTILITY .................................................................... 8
2.2 EASY SETUP BY UTILITY FOR PRINTER SHARING .......................................... 12
2.3 EASY SETUP BY CONFIGURING WEB PAGES .................................................. 17
CHAPTER 3 MAKING CONFIGURATION ..................................................................... 21
3.1 BASIC SETTING ..................................................................................................... 22
3.2 FORWARDING RULES .......................................................................................... 36
3.3 SECURITY SETTING .............................................................................................. 39
3.4 ADVANCED SETTING............................................................................................ 44
CHAPTER 4 TROUBLESHOOTING ...................................................................... 64
APPENDIX A. SPEC SUMMARY TABLE.......................................................................... 67
APPENDIX B. LICENSING INFORMATION ...................................................................... 69

4
Chapter 1 . Introduction
Congratulations on your purchase of this outstanding product: WiFi Broadband Router.
This product is specifically designed for those who need to have the file sharing and P2P
download services beyond his home and office. It provides a complete solution for Internet
surfing and broadband sharing. Instructions for installing and configuring this product can
be found in this manual. Before you install and use this product, please read this manual
carefully for fully exploiting the functions of this product.
1.1 Package List
Items Description Contents Quantity
1 WiFi Broadband Router 1
2 Antenna 2
3 Power adapter 1
4 CD 1

5
1.2 Hardware Installation
1.2.1 Hardware configuration
USB Connector
Reset Button
WAN LED
LAN LED 1－4
WPS/USB OFF Button
Status LED
Power LED
USB LED
WiFi LED
ANTENNA Connector
Power Switch Button
Power Connector
WAN Port
LAN Port 1－4
ANTENNA Connector

6
1.2.2 LED indicators
LED Status Description
Status LED
Green Power ON
Green USB storage attached
Green in flash Data access
USB LED Green in flash
then stop
Press ‘USB off’ button till LED flashing, then
can remove USB storage when LED stop
flashing.
Green It is connected to local Ethernet.
WAN LED Green in flash Data access
Green RJ45 cable is plugged
Ethernet LED Green in flash Data access
Green WLAN is on
WiFi LED
Green in flash Data access
Power LED Green Power ON
How to Operate
DO NOT connect WiFi Broadband Router to power before performing the
installation steps below.
Step 1.
Screw the antenna in a clockwise direction
to the back panel of the unit.
Step 2.
Plug the RJ45 cable into LAN port 1~4 and
connect with your PC or NB.

7
Step 3.
Plug your RJ-45 into the WAN port and
connect with your xDSL modem.
Step 4.
Plug the power jack into it.
Step 5.
Power ON.
Step 6.
Prepare a USB Storage or Printer, and then
plug into the USB port.

8
Chapter 2 . Getting Started
Please use windows EZ setup utility or Web UI wizard to enter the setup process.
2.1 Easy Setup by Windows Utility
Step 1.
Install the Easy Setup Utility
from the provided CD then
follow the steps to configure
the device.
Step 2.
Select Language then click
“Next” to continue.
Step 3.
Then click the “Wizard” to
continue.

9
Step 4.
Click “Next” to continue.
Step 5.
One free DDNS account
‘ MAC address.ezguard.net’
for end user to access the
NAS router remotely, you can
rename an alias name to
remember it easily. Once you
type in a name, you can click
‘ check’ to see if the name
server accept it or not. You
also can click ‘Ignore’ to pass
it.
Step 6.
Select Wireless Enable, and
then click “Next” to continue.

10
Step 7.
Enter SSID, Channel and
Security options, and then
click “Next” to continue.
Step 8.
Select Auto Detect WAN
service.
Step 9.
Save the setting.

11
Step 10.
Congratulations!
Setup is completed.
Now you have already
connected to Internet
successfully.

12
2.2 Utility for Printer Sharing
Step 1.
Install the Easy Setup Utility
from the provided CD then
follow the steps to configure
the device.
Step 2.
Select Language then click
“Next” to continue.
Step 3.
Please enter your information
Then press next to continue.
Step 4.
Install USB Device Server to
Your PC.

13
Step 5.
Click Install to begin the
installation.
Step 6.
Processing.
Step 7.
Install Completed. Then you
can click icon at your PC to
run the program of printer
sharing.
Once you accomplish the utility of printer sharing, you can execute the program
and follow the following steps to setup the printer and start to print.

14
Step 8.
When you run the utility, you
can go to
‘tool‘->‘Configuration’ to
change the language you
wish.
Step 8-1.
Select Language
Step 9.
Once your printer is ready to
plug in router, please make
sure your PC already installed
the printer driver in Windows.
After you plug in USB printer,
you can see the printer’s
name on Utility, then please
click ‘ Connect’ to connect
with system.
you can print successfully
through network now.
Note: You can uninstall this
utility through Windows
Program files.

15
Step 9-1.
If you want your printer to
connect automatically next
time, you can click on the icon
of ‘Auto Connect Printer’.
Step 10.
We only allow one printer job
to be printed at the same
network, so once 2nd print job
to be executing, the system
will send a warning message
on both PCs.

16
Step 10.
If 2nd print job want to be
printed immediately, the user
of 1st print job can accept the
user of 2nd print job to control
the printer, if the user of 1st
print job free to release, then
the user of 2nd print job can
control the printer.

17
2.3 Easy Setup by Configuring Web UI
You can also browse UI of the web to configure the device.
Browse to Activate the Setup Wizard
Type in the IP Address
(http://192.168.123.254)
Type the default
Username and password
‘admin’ in the System
Password and then click
‘login’ button.
Select your language.
Select “Wizard” for basic
settings in simple way.
Press “Next” to start the
Setup Wizard.

18
Configure with the Setup Wizard
Step 1
You can change the
password of administrator
here.
Step 2
Select Time Zone.
Step 3
You can select Auto
detecting WAN type or
setup WAN type
manually.

19
Step 4
The system will detect the
WAN type if you choose
to let the system detect
automatically.
Step 5
Type in Host name and
ISP registered MAC
address. (if no such
information, you can go
next)
Step 5-1
Wireless setting.
Step 5-2
Wireless authentication
and encryption.

20
Step 6
Check the information
again.
Step 7
System is applying the
setting.
Step 8
Click finish to complete it.