Zanussi ZFG215S User manual

GETTING
STARTED?
EASY.
User Manual
ZFG215S
EN User Manual
Cooker Hood

VISIT OUR WEBSITE TO:
Get usage advice, brochures, trouble shooter, service and repair information:
www.zanussi.com/support
SAFETY INFORMATION AND INSTALLATION
WARNING! Refer to the separate
Installation Instructions booklet for
Safety Information and Installation.
Read carefully the Safety chapters
before any use or maintenance of the
appliance.
PRODUCT DESCRIPTION
CONTROL PANEL OVERVIEW
1 2
3
Function Description
1Light switch To switch the light on and off.
2Fan speed switch To switch between fan speed level.
3Indicator Indicates if the hood operates.
DAILY USE
USING THE HOOD
Check the recommended speed according to the
table below.
While heating up food, cooking with covered pots.
While cooking with covered pots on multiple cooking zones or burners, gentle frying.
While boiling and frying big quantities of food without a lid, cooking on multiple cooking
zones or burners.
2

It is recommended to leave the hood
operating for approximately 15 minutes
after cooking.
To operate the hood:
Move the fan speed switch to one of the speed
levels.
The hood starts to operate. If needed, change the
speed by moving the switch.
The hoods light works independently
to other hood functions. To illuminate
the cooking surface use the light
switch .
To turn off the appliance move the fan speed switch
to the 0 position.
CARE AND CLEANING
NOTES ON CLEANING
Cleaning
Agents
Do not use abrasive detergents and brushes.
Clean the surface of the appliance with a soft cloth with warm water and a mild
detergent.
After cooking some parts of appliance can get hot. To avoid stains appliance
must be cooled down and dried with clean cloth or paper towels.
Clean stains with a mild detergent.
Keep the hood
clean
Clean the appliance and grease filters each month. Clean the interior and grease
filters carefully from fat. Fat accumulation or other residue may cause fire.
Grease filters can be washed in a dishwasher.
The dishwasher must be set to a low temperature and a short cycle. The grease
filter may discolour, it has no influence on the performance of the appliance.
Charcoal filter
The time of saturation of the charcoal filter varies depending on the type of cook-
ing and the regularity of cleaning the grease filter. The activated charcoal filter is
not washable, cannot be regenerated and must be replaced approximately every
4/6 months of operation, or more frequently for particularly heavy usage.
CLEANING THE GREASE FILTER
Filters are mounted with the use of clips and pins
on the opposite side.
To clean the filter:
1. Press the handle of the mounting clip on the
filter panel underneath the hood.
1
2
2. Slightly tilt the front of the filter downwards,
then pull.
Repeat the first two steps for all filters.
3. Clean the filters using a sponge with non
abrasive detergents or in a dishwasher.
3

The dishwasher must be set to a low
temperature and a short cycle. The
grease filter may discolour, it has no
influence on the performance of the
appliance.
4. To mount the filters back follow the first two
steps in reverse order.
Repeat the steps for all filters if applicable.
REPLACING THE CHARCOAL FILTER
WARNING! The charcoal filter is
NON-washable! The filter cannot be
regenerated!
To replace the charcoal filter:
1. Remove the grease filters from the appliance.
Refer to "Cleaning the grease filter" in this chapter.
2. Turn the filter counterclockwise (1) and then
pull (2).
1
2
To mount the filters back follow the steps in reverse
order.
In any case, it is necessary to replace the filters at
least every four months.
REPLACING THE LAMP
WARNING! Risk of burns and electric
shock! Disconnect the appliance from
the electricity before the operation!
Make sure that the light bulb has
cooled down before touching it.
WARNING! Risk of injury! Use
protective gloves to replace the lamp.
Risk of damage to the appliance! Do
not use sharp edged tools!
Replace the burnt light bulb in accordance with the
specifications:
Power (W) 4
Socket E14
Voltage (V) 220 - 240
Dimensions (mm) 37 x 100 (diameter x
length)
ILCOS D Code (ac-
cording IEC 61231)
DRBB/
F-4-220-240-
E14-37/100
To replace the lamp:
1. The lamp cover has two slots on each side (1).
Use a flat non sharp plastic tool. Gently remove
the lamp cover from the appliance (2).
2. Replace the lamp.
3. Mount the lamp cover.
ENVIRONMENTAL CONCERNS
Recycle materials with the symbol . Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
4
*

WWW.ZANUSSI.COM/SHOP
867351641-A-012022