Zap ACC200 User manual

© 2022 System Q Ltd
1
Slim & Compact Exit Buttons
Zap is a registered trademark of System Q Ltd
Document ref: qACC200-253
ZapCCTV.com
ACC200-202, ACC250-253 - Quick Start Guide
Exit Buttons
This guide covers the slim exit buttons which are made
from zinc alloy with a matt finish. Their slim footprint means
they can fit most locations and come supplied with their
own back box.
This guide also covers the compact exit buttons, just 53mm
wide with a built-in back box. The options available also
include the LED illuminated ACC253 model.
User Information
· There are no user serviceable parts, opening or attempting to repair the product will void the
warranty.
· Do not install or use the device if the wires connected are damaged or have been subjected to
water ingress.
· Shut off all power to the access control system before wiring this device.
· Maintain a clean and safe environment at all times.
Definition
NO (Normally Open) - This is a contact which remains open (as default) until activated, during the
"active" state the contact provides a closed circuit and starts conducting.
NC (Normally Closed) - Is the opposite of a NO contact. The contact will remain closed (as default)
until activated, during the "active" state the circuit breaks and stops current flow.
Setup Example
Exit buttons are used in access control
systems to provide a momentary
contact signal to the access controller
to open a magnetic lock.
This example shows a "Fail-safe"
scenario. When the exit button is
pressed the access control power
supply then releases power from
the lock, and if power is lost then
the lock also releases.
Wire in NO or NC depending on
the access controller used and
also on the required state of the
lock during a "Fail-safe" or "Fail-
secure" scenario.

This symbol indicates that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated
WEE/CG0783SS collection point as defined by your local council.
© 2022 System Q Ltd
2
Slim & Compact Exit Buttons
Zap is a registered trademark of System Q Ltd
Document ref: qACC200-253
All specifications are approximate. System Q Ltd reserves the right to change product specifications or features without notice. Whilst every effort is
made to ensure that these instructions are complete and accurate, System Q Ltd cannot be held responsible for any losses, no matter how they arise,
from errors or omissions in these instructions, or the performance or non-performance of the equipment refered to.
Connections - ACC200
For operation with a door access control panel and lock, the exit
button is provided with NO/COM terminals.
Connections - ACC202, ACC250-252
For operation with a door access control panel and lock, the exit
button button is provided with NC or NO and COM connection wires.
Connections - ACC253
For operation with a door access control panel and lock, the exit
button is provided with NC or NO.
The ACC063 also has a built in blue LED which requires 12V DC (not
supplied with the product).
Troubleshooting
If the exit button is not activating the lock then there is likely a shorted wire, open circuit or some
other failed device in the circuit.
To identify where the fault is, each wired connection in the circuit needs to be tested; working from
the push button progress through, including the keypad, the access controller, power supply and the
magnetic lock.
If the fault is with the access control button then check the connection wires for continuity and for
trapped wires. Check for water ingress on the wired connections. Check the polarity in the power
connections and ensure the connections are connected to the proper terminals.
Specification
ACC200
ACC202
ACC250-252
ACC253
Construction
Zinc Alloy
Zinc Alloy
Zinc Alloy
Zinc Alloy
Terminals
NO/Common (Screw
Terminals)
NO/NC/Common
(Wires)
NO/NC/Common
(Wires)
NO/Common/ +12V
DC/ GND (Wires)
Rating
2A12V DC Max
2A12V DC Max
0.5-1A 12V DC Max
0.5-1A 12V DC Max
LED Colour
~
~
~
Blue LED
Dimensions
80 x 30 x 26mm
93 x 35 x 28mm
53 x 53 x28mm
53 x 53 x28mm