Zap ACC060 User manual

Quick Start Guide - qACC060-063, qACC100-103, qACC150-153 Copyright 2021 System Q Ltd
1
Press To Exit Buttons
Zap is a registered trademark of System Q Ltd
ACC060-063, ACC100-103, ACC150-153 - Quick Start Guide
Press To Exit Buttons
The classic green and red buttons are made of anodised
aluminium for a quality feel and look. The ACC063 features an
illuminated button so you can see it in low light and the ACC062
is a simple, discreet "Press to Exit" button in a modern, minimalist
design.
This guide also covers the easy read "Press to Exit" buttons, great
for public areas as simple and discreet options in a modern
minimalist design. The faceplate models have standard screw
hole centres to fit standard UK back boxes. If you are not fitting
these into a flush mount back box we recommend purchasing
one of our surface mount boxes.
User Information
· There are no user serviceable parts. So opening or attempting to repair the product will void the warranty.
· Do not install or use the device if the wiresconnected are damaged or have been subjected to water
ingress.
· Shut off all power to the access control system before wiring this device.
· Maintain a clean and safe environment at all times.
Definition
NO (Normally Open) - This is a contact which remains open (as default) until a activated, during the "active"
state the contact provides a closed circuit and starts conducting.
NC (Normally Closed) - Is the opposite of a NO contact. The contact will remain closed (as default) until a
activated, during the "active" state the circuit breaks and stops current flow.
Setup Example
"Press to Exit" buttons are used in access
control systems to provide a momentary
contact signal to the access controller to
open a magnetic lock.
This example shows a "Fail-safe"
scenario. When the "Press to Exit"
button is pressed the access control
power supply then releases power
from the lock, and if power is lost
then the lock also releases.
Wire in NO or NC depending on the
access controller used and also on
the required state of the lock during
a "Fail-safe" or "Fail-secure" scenario.

Quick Start Guide - qACC060-063, qACC100-103, qACC150-153 Copyright 2021 System Q Ltd
2This symbol indicates that equipment must not be mixed with general household waste. For treatment, recovery and recycling please return to your local designated
WEE/CG0783SS collection point as defined by your local council.
All specifications are approximate. System Q Ltd reserves the right to change product specifications or features without notice. Whilst every effort is
made to ensure that these instructionsare complete andaccurate, System Q Ltd cannot be held responsible for any losses, no matter how they arise,
from errors or omissionsin these instructions,or the performance or non-performance of the equipment refered to.
Press To Exit Buttons
Zap is a registered trademark of System Q Ltd
Connections - (ACC060-062, ACC100-103, ACC150-153)
For operation with a door accesscontrol panel and lock, the "Push to Exit"
button is wired with NC or NO.
Connections - (ACC063)
For operation with a door accesscontrol panel and lock, the "Push to Exit"
button is wired with NC or NO.
The ACC063 also has a built in blue LED which requires 12V DC (not
supplied with the product).
Troubleshooting
If the "Push to Exit" is not activating the lock then there is likely a shorted wire,open circuit or some other failed
device in the circuit.
To identify where the fault is, each wired connection in the circuit needs to be tested working from the push
button progress through, including the keypad, the access controller, power supply and the magnetic lock.
If the fault is with the access control button then check the connection wires for continuity and for trapped
wires. Check for water ingress on the wired connections.Check the polarity in the power connections and
ensure the NO or NC connections are connected to the proper terminals.
Specification
ACC060/1/2
ACC063
ACC100/1/2/3
ACC150/1/2/3
Construction
Stainless Steel
Stainless Steel
Front – Stainless Steel /
Button - Plastic
Front – Stainless Steel /
Box & Button -
Polycarb
Terminals
NO/NC/Common
NO/NC/Common/ +12V
DC/ GND
NO/NC/Common
O/NC/Common
Rating
0.5-1A 12V DC
0.5-1A 12V DC
0.5-1A 12V DC
0.5-1A 12V DC
LED Colour
N/A
Blue LED
N/A
N/A
IP Rating
IP65 Wateproof
IP65 Wateproof
Internal Use Only
Internal Use Only
Dimensions
86 x 86 x 42mm
86 x 86 x 42mm
86 x 86 x 30mm
86 x 86 x 30mm