Zebronics ZEB JUKE BAR 9102 PRO DOLBY User manual

www.zebronics.com
User Manual

Important Safety Instruction
Thank you for purchasing the ZEB-JUKE
BAR 9102 PRO DOLBY. Please read this user
manual carefully and keep for future
reference.
Warning
Caution:
Ÿ To reduce the risk of electric shock, do not
dismantle the product and do not expose the
apparatus to rain or moisture. No user-
serviceable parts inside.
Ÿ Refer servicing to qualified personnel only.

The lightning flash within an
e q u i l a t e r a l t r i a n g l e i s
intended to alert you to the
presence of uninsulated
dangerous voltage within the
product’s enclosure that may
be of sufficient magnitude to
constitute an electric shock to
a person or persons.
Important! This symbol alerts
you to read and observe
important warning s and
instructions on the unit or in
this manual.
1. To prevent possible hearing damage, do not
listen at high volume levels for long time
periods or a sudden high volume level.
2. Never use the device unsupervised! Switch
off the device whenever you are not using it,
even if not using it only for a short while.
3. The appliance is not intended to be operated
by means of an external timer or separate
remote control system.
4. If the supply cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified persons in order to avoid
a hazard.

5. Before operating this system, check the
voltage of this system to see if it is identical to
the voltage of your local power supply.
6. The unit should not be impeded by covering
the ventilation opening with items such as
newspaper, table-cloths, curtains etc. Make
sure that there are at least 20 cm of space
above and at least 5 cm of space on each side of
the unit.
7. The apparatus must not be exposed to
dripping or splashing liquid, no objects filled
with liquids such as vases, should be placed on
the apparatus.
8. To prevent fire or shock hazard, do not
expose this equipment to direct heat, rain,
moisture or dust.
9. Do not position this unit near any water
sources e.g. taps, bathtubs, washing machines
or swimming pools.
Ensure that you place the unit on a dry, stable
surface.
10. Do not place this unit close to a strong
magnetic field.
11. Do not place the unit on a amplifier or
receiver.
12. Do not place this unit in a damp area as the
moisture will affect the life of electric
components.

13. Do not attempt to clean the unit with
chemical solvents as this might damage the
finish. Wipe with a clean, dry or slightly damp
cloth.
14. When removing the power plug from the
wall outlet, always pull directly on the plug,
never pull on the cord.
15. Depending on the electromagnetic waves
used by a television broadcast, if a TV is turned
on near this unit while it is also on, lines might
appear on the LED TV. Neither this unit nor the
TV is malfunctioning. If you see such lines, keep
this unit well away from the TV set.
16. The mains plug is used to disconnect the
device, the disconnected device should remain
readily operable.
Important Safety Instructions
1. Read these instructions. Keep these
instructions. Follow all instructions. Heed all
warnings.
2. Do not use this apparatus near water.
3. Clean only with dry cloth.
4. Do not block any ventilation openings. Install
in accordance with the manufacturer's
instructions.
5. Do not install near any heat sources such as
radiators, heaters, stoves, or other apparatus
(including amplifiers) that produce heat.

6. Protect the power cord from being walked
on o r p i nc h ed p a r t i cu l ar l y a t p lu g s,
convenience receptacles or at the point where
they exit from the apparatus.
7. Only use attachments/accessories specified
by the manufacturer.
8. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
9. Refer all servicing to qualified service
personal. Servicing is required when the
apparatus has been damage in any way, for
example, when the power-supply cord or plug
is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Preparation for Use
Unpacking and Set Up
1. Remove the Sound bar from the carton and
remove all packing material from the Sound
bar. Save the packing material, if possible, in
case the Sound bar ever needs to be serviced
or transported. The original carton and
packing material is the only safe way to pack
your Sound bar to protect it from damage in
transit.

2. Remove any descriptive labels or stickers on
the front or top of the cabinet. Do not remove
any labels or stickers from the back or bottom
of the cabinet.
3. Place your Sound bar on a level surface such
as a table, desk or shelf, convenient to an AC
outlet, out of direct sunlight, and away from
sources of excess heat, dirt, dust, moisture,
humidity, or vibration.
4. Unwind the Line cord connecting the AC
adapter and extend it to its full length.
Protect Your Furniture
This model is equipped with non-skid rubber
'feet' to prevent the product from moving
when you operate the controls. These 'feet' are
made from non-migrating rubber material
specially formulated to avoid leaving any
marks or stains on your furniture. However
certain types of oil based furniture polishes,
wood preservatives, or cleaning sprays may
cause the rubber 'feet' to soften, and leave
marks or a rubber residue on the furniture.

To prevent any damage to your furniture we
strongly recommend that you purchase small
self-adhesive felt pads, available at hardware
stores and home improvement center
everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place
the unit.
Important Notes
Ÿ Safety and operating instruction manual
should be retained for future reference.
Ÿ The apparatus should not be exposed to
dripping, splashing or placed in a humid
atmosphere such as a bathroom.
Ÿ Do not install the product in the following
areas:
Ÿ Places exposed to direct sunlight or
close to radiators.
Ÿ On top of other stereo equipment that
radiate too much heat -Blocking ventilation or
in a dusty area.
Ÿ Areas where there is constant vibration.
Ÿ Humid or moist places.
Ÿ Do not place near candles or other
flames.
Ÿ Operate the product only as instructed
his manual.
Ÿ Before turning on the power for the first
time, make sure the sound bar is plugged to
power outlet.

Ÿ For safety reasons, do not remove any
covers or attempt to gain access to the inside of
the product. Refer any servicing to qualified
personnel.
Ÿ Do not attempt to remove any screws, or
open the casing of the unit; there are no user
serviceable parts inside. Refer all servicing to
qualified service personnel.
Product Representation
Sound Bar & Sub-Woofer

1. LED Display
2. SW OUT
3. USB
4. AUX
5. OPTICAL
6. HDMI(ARC)
7. AC IN
8. Power/Standby
9. INPUT
10. VOL-
11. VOL+
Remote Control

1. : Standby mode for power on/off.
2. PAIR: 2. RESET/PLAY: (Reset EQ and volume in any
mode, high and low tuning )Reset: Press and hold the
button more than 3 sec. to Set all functions to
manufacturer defaults.
3. VOL+ : Master Volume Up.
4. 9 : Pre button: Previous program (Only work under
USB & BT Mode).
5. VOL- : Master Volume Down.
6. Light control key：Short press: Switch the LED
light effect Long press: On-off LED light effect
7. BASS+
8. BASS-
9. MUTE : Mute Mode.
10. INPUT : Input mode(AUX/USB/HDMI(ARC)/COA/BT)
11. : : Next button: Next program. (Only work under
USB and BT mode).
12. 4
; Play/Pause (Only work under USB and BT
mode).
13. Lighting adjustment:Press down 50% , press
down 20% ,
press down 10%.
14. MUSIC NEWS : Select the News EQ effect.
15. TR+ : Treble volume up.
16. TR- : Treble volume down
17. MOVE/3D : Select the MOBIE/3D EQ effect

Positioning the Sound Bar
Place on a flat Surface
Place the sound bar horizontally on a flat
surface such as a TV unit or shelves and align it
centrally with the TV screen. Allow some space
between the speaker and the wall. Don’t place
inside a cabinet or an a walled shelf. Follow this
guidance for best sound output and good
airflow around the sound bar.
Mount on the wall
WARNING : If you don’t feel confident to
correctly and securely wall-mount the sound
bar, Seek the assistance of an experienced
person or professional.
Install the speaker on a vertical, fast,
reinforced area of wall. For plaster walls, it is
recommended to screw into wall studs for
greater security. For optimum performance,
allow at least 25mm/1’’distance between the
sound bar and the TV.
ü

Follow below steps to mount the sound
bar on the wall
1. Make 2 holes on the wall with distance same
as the wall bracket on the soundbar
2. Put the plastic anchors onto the wall and
secure the screws to the plastic clip, do not
tighten the screws all the way make sure leave
some space
3. Once the screws securely fastened, hang the
sound bar over by inserting the screws onto
the wall mount bracke

OPERATE INSTRUCTIONS
Setting the Soundbar
1. Plug in the power cord and the display will
light up (Standby mode)
2. Switch on the soundbar by using power
button on soundbar or by using STANDBY
button on remote. After switching on, the
default input mode will appear on display.
3. Input mode can be changed by pressing the
input button again or by using the INPUT
button on remote.
4. Below are input mode names appearing in
the soundbar display:
BT : BT Pairing Mode
AU : AUX Mode
Hd : ARC Mode
opt : Optical Mode
US : USB Mode
BREATHING LED LIGHT COLOR SELECTION
1. When you connect with the soundbar to the
power ,the screen goes into standby mode.
Press the Power/Standby key and the
soundbar will enter the mode selection.The
LED light sources on both sides light up. Press
the INPUT key to select the mode you want.
2. Short press the breathing LED light button
on the remote control and choose the colour to
you like.

Powering On/Off
1. Plug the power cord of sound bar into a
wall outlet, it will automatically enter standby
mode
2. Short-press the “STANDBY” button on
sound bar or on remote controller to turn on
the sound bar
3. To turn off, press and hold the “STANDBY”
button for 2 seconds, then unplug from wall
outlet.

Playing Audio via BT Connection
1. Turn on sound bar and then short-press
the multi-function button to switch to BT mode
and the LED will show BT
2. Activate the pairing function on your
phone of other compatible device and select
"ZEB-JUKE BAR 9102 PRO DOLBY”.
3. When successfully paired, you will hear a
tone and the LED Display will stay on.
4. The remote control includes BT mode
playback controls
Notes:
Using the Soundbar

Playing Audio via USB Port
The sound bar automatically switches to
USB input mode with the LED display US when
a USB flash drive is inserted (this mode isn't
selectable on the sound bar or remote control
unless a USB flash drive is connected).
1. Ensure that your USB flash drive
contains MP3 audio files (other file types not
supported).
2. Connect the USB flash drive to the USB
port on the sound bar (or your own USB
extension cable connected to the USB port);
music will automatically play.
3. The remote control includes USB input
mode playback controls.
Audio input(Aux)Connection
Firstly connect the soundbar to your PC,
laptop, smart-phone, TV, or other audio
devices by using an AUX cable
provided. Make sure that these devices have
both AUX IN and AUX OUT terminals.
2. Then press the STANDBY button or INPUT
button on remote control to switch the
soundbar to Aux mode, once the soundbar is
connected in Aux mode, the screen will display
"AUX” . And the music on your connected
device will play. Playback can only be
controlled on your connected device.

Note: For some computers, you may need to
access the audio control panel to manually set
the soundbar as shown steps on above.
HDMI (ARC) Mode
1. The soundbar supports HDMI (ARC) with
audio return channel (ARC). You can hear the
TV audio through your soundbar by using a
single HDMI (ARC) cable. But on condition that
your TV is ARC compliant.
2. Using a high speed HDMI (ARC) cable,
connect the HDMI (ARC) connector on the
soundbar to the HDMI (ARC) connector on the
TV. The HDMI (ARC) connector on the TV might
be labeled differently. For details, see the user
manual of your TV.
3. When HDMI (ARC) is connected, TV sound
setting in “sound output” mode should be set
as <external Dolby or Auto mode>, in addition,
digital audio output mode should be set as
<automatic> or <decoded output as Dolby>.
When the HDMI (ARC) cable is connected, the
TV digital audio output is set as Dolby or Auto
mode. Then start playing music on the TV.
4. Press “INPUT” button on the remote control
or “STANDBY” button on soundbar to select -
HDMI (ARC) mode.
Different TV might be different setting, please
refer to your TV User Manual.

5. Use the volume buttons to adjust the volume
to your requirements.
6. You can also change the audio settings by
using the relevant buttons on the remote
control.
Note:
1. When connecting a device such as a TV/Set-
top box/DVD/ game console with HDMI (ARC)
cable, set the audio
output mode of the device to Dolby or Auto
mode <digital HDMI (ARC) output>.
2. The TV is connected to a HDMI (ARC) port
with sound bar. Different TVs might have
different setup menus,but the operation
approach is the same.
3. If needs to connect set-up box meanwhile,
please firstly connect the HDMI (ARC)
connector and paired to the
soundbar. Then connect the set-top box
Optical Mode
Remove the cap of optical cable (keep the cap
for the future use); check the direction of the
plug. Connect the soundbar and TV with the
optical cable.
-Use this mode to play music from a TV
with optical digital output on the sound bar. In
TV sound settings, select the soundbar optical
connection (output for audio). When the
optical cable is connected, the TV audio output
is set to Dolby or Auto mode.

-The TV must have an optical digital
output. Use the optical cable to make the
connection as follows:
1. Connect the optical cable to the optical
digital output of your TV.
2. Connect the optical cable to the optical
digital input of your soundbar.
3. Switch on the TV set and the soundbar. Set
the connected TV to “Dolby or Auto mode”.
4. Start playing on the TV.
5. Press “INPUT” button on the remote control
or “STANDBY” button on the soundbar to select
- OPTICAL mode.
6. Use the volume buttons to adjust the volume
to your requirements.
7. You can also change the audio settings by
using the relevant buttons on the remote
control
Note:
1. When connecting a device such as a TV/Set-
top box/ DVD/ game console with optical cable,
set the audio output
mode of the device to Dolby or Auto mode
(digital optical output).
2. Do not bend the optical cable, otherwise the
cable inside will be damaged.