ZEBSBOARDS EZInstall Kit V2 User manual

EZInstall Kit V2 Installation
Mounting the Kit
The kit should be mounted as shown in the illustration above. Recommended positioning
would be to install as far forward in the cabinet as possible, putting the flipper solenoids
(furthest forward solenoids on side panels) close to the flipper switches ensuring the best
response and feedback for them as possible. Ensure that at least ¾” (19mm) space is left
between the top of the solenoids and the bottom of the playfield monitor.
Install the side panels with the slot opening to the rear of the kit on a slight downward angle
toward the front and in a parallel position in the cabinet and slide the mainboard into the slot
from the rear.
Use mounting screws appropriate in length to the thickness of your cabinet construction and
install them in the mounting holes provided making sure not to puncture the outside face of
the cabinet.

Power Connections (AC MAINS)
While the supplied power supply has built in short circuit and thermal overload a 10A external circuit
protector (circuit breaker) has been installed in the power box.If at any time the power to the kit is
interrupted, please check and reset the circuit breaker if necessary. Make sure the 110v /220v selector
is set to the correct AC voltage for your country.
Installation of the wiring using a plug vs hard wiring to the mains is highly recommended.
!! AC MAINS ELETRICITY IS DANGEROUS AND CAN KILL YOU. If
you have any doubts about your capabilities it is
recommended that you contact a professional to install the
unit for you !!!!

Left and Right Panel Connections
Connect the left panel connectors to the corresponding connectors on the mainboard as shown
in the illustration below.
The open ports on the 12V distribution board are provided to supply additional 12V toys if
desired.
There is a 10A standard automotive blade fuse in the black fuseholder below the power supply
protecting the booster module (red board) which powers the replay knocker. If the replay
knocker ceases to function please check and or replace the 10A fuse. Do Not Exceed a 10A
Rating when replacing the fuse.

Connect the right panel connectors to the corresponding connectors on the mainboard as
shown in the illustration below.

The 4 open terminals on the Booster Board connector can be used for future expansion (beacons, fan,
button lighting, etc.)
To expand the system, simply connect the negative side of the toy to the open port on the booster
board and connect the positive side of the toy to the appropriate positive voltage source (12V is
supplied by the kit, other voltages will require an additional power supply.)
LIGHTBAR/STROBES CONNECTION
Mount the lightbar in the desired location and connect the ribbon and power cables to the Resistor
Board as shown below.

Solenoid Bar Connections
Ensure that the 6 pin connector at the left of the bar is connected to the left panel as previously
described…..
… and connect the 8 pin connector at the right side to the booster board as shown below.

From Left to Right the pinout for the Solenoid Bar and Right Panel connectors is as follows:

USB Cable Connection
Connect the USB cable from the PacLED64 (shown below) to a free USB port in your computer.

Adjustments
Speed Control
The shaker motor speed can be adjusted by turning the trim pot located on the speed control board at
the front of the right panel.
Night Mode
A night mode switch has been installed which will allow you to turn off the booster board controlling the
solenoids, shaker motor and replay knocker. Enough cable has been provided to allow for remote
mounting of the switch to a convenient location.
To activate night mode simply flip the switch to the off position. Switching it to the on position will re-
enable the solenoids.

Software Setup
Pacled64 units ship from Ultimarc with a default demonstration (attract) pattern burned into
the firmware. Since this pattern uses pwm across all of the outputs and solenoids (particularly
the replay knocker) don’t play nicely with pwm (it causes a huge draw in power) this pattern
needs to be turned off.
To turn off the demo pattern you will need to download the pacled64 utility from here ….
https://www.ultimarc.com/PacLED64.exe
Install the utility in Administrator mode and run it. You will be presented with this screen …
(hopefully yours shows a green bar and Device1 present. I had no pacled connected at the time)

Click on the Brightness tab and you will come this screen ….
Set the slider all the way to the left to turn down the brightness and set the LED number to 0.
This effectively turns off all outputs during the demo pattern.
Return to the 1st screen and click the Start Recording to Flash button. After about 20 seconds
or so click on the stop recording to flash button. Click on the OK button and exit the utility.
BEFORE turning on the NIGHT MODE SWITCH for the 1st turn on the kit and
ensure that the lightbar is not running a pattern, if it is, rerun the above steps.
Zebsboards is not responsible for damage caused by adverse side effects of
controllers and or software setup.

DOF Configuration
**Standard Kit Settings