16 | 200
Replacing the lens cap
To replace the lens cap (2), unscrew the screws (3) using a screwdriver. Remove the
retaining plate (4) and the defective lens cap (2). Fit the new lens cap (2) and retaining
plate (4). Tighten the screws (3) using a screwdriver.
Regulatory Information USA and Canada
USA:
FCC-ID: 2AMSPDTI335
Kanada:
IC-ID: 22938-DTI335
CAN ICES-3 (B)/NMB-3(B)
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and(2)this device must accept any interference received, including interference
thatmay cause undesired operation.
2. Changes or modications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modications to this equipment. Such modications could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
Ifthis equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
thereceiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
Name of Responsible Party
Carl Zeiss SBE, LLC / Consumer Products
ZEISS Group
One North Broadway, Suite 1501
White Plains, NY, 10601, USA
Phone +1 800 858 6745
We, Carl Zeiss Inc. hereby declare that this product was tested conforming to the
applicable FCC rules under the most accurate measurement standards possible, and that
all the necessary steps have been taken and are in force to assure that production units of
the same equipment will continue to comply with the Commissions requirements.
Regulatory Information California
The BC mark indicates that this product is in compliance with the California
Energy Comissions regulations on battery chargers.
Power supply unit manufaturer
Shenzhen Simsukian Electronic Technology Co., Ltd.
Building 1, the 5th plant, Jiayi Industrial Park
Daping Community, Guanlan Street Longhua District
Shenzhen P.R. China
Model identier: SK22G-0500200Z
TECHNICAL DATA ON POWER SUPPLY UNIT
(2)
(4)
(3)
(1)
Care and maintenance of the device
Do not rub coarse particles (e.g. sand) from the lenses. Blow them o, or use a soft
brush! Over time, ngerprints can corrode the lens surface. Breathing on the lens
and polishing it with a clean optical cleansing cloth is the easiest method of cleaning
thelens surface.
Dry storage and keeping the outer lens surfaces well ventilated, especially in
thetropics, helps to prevent a possible mold lm forming on the optics.
Your ZEISS DTI 3/35 requires no further special care.
Care and maintenance of the battery
Follow these steps to extend the battery life:
• Avoid storing the device at high temperatures.
• Avoid storing the device with a fully charged battery.
• Avoid complete discharging of the device.
Spare parts
Should you require spare parts for your device, e.g. the lens cap, please contact your
specialist retailer, your local distributor or our after-sales service.
For Customer Service inquiries we are happy to take your calls from Monday to Friday
from 8:00 a.m. to 4:30 p.m. (CET).
Tel.: +49 (0) 800 934 77 33
Fax: +49 (0) 64 41-4 83 69
ZEISS is a byword for reliability and a high level of quality. Therefore, quite independently
of the seller‘s warranty obligations to the customer, we themanufacturer oer a two
year warranty on this ZEISS product, which can beextended for a further year upon
registration of the product if registration is madewithin four weeks of purchase.
Thescope of the warranty can be seen by accessing the following link:
www.zeiss.com/cop/warranty
Register your product at: www.zeiss.com/cop/register
Manufacturer‘s address
Carl Zeiss AG
Carl-Zeiss-Strasse 22
D-73447 Oberkochen
www.zeiss.com/nature and www.zeiss.com/hunting
Subject to changes in design and scope of supply due to technical improvements.
No liability for mistakes and printing errors.
Data protection notice
Personal data is processed when using the DTI 3/35.
Our information on data protection and the processing of personal data can
be found in our download center: www.zeiss.com/hunting/manuals
Legal and regulatory information
Wireless transmitter module frequency range: WLAN: 2,412 - 2,462 MHz
Wireless transmitter module power: 100 mW
Carl Zeiss AG thus declares that the thermal imaging camera
DTI 3/35 complies with the directives 2014/53/EU and
2011/65/EU. The full text of the EU declaration of conformity
as well as additional information are available at:
www.zeiss.com/dti-335/conformity.
Carl Zeiss AG
Carl-Zeiss-Strasse 22
73447 Oberkochen
Germany
www.zeiss.com/nature
www.zeiss.com/hunting
Electronics
Input voltage VAC 100 - 240
Input frequency Hz 50 / 60
Output voltage VDC 5
Output current A 2
Power output W10
Average operating eciency %82.98
Power consumption at zero load W 0.068
Ambient conditions
Operating temperature °C (°F) -0 / +40 ( -32 / +104)
Relative humidity rH 25% - 90%
Storage temperatures °C (°F) -30 / +60 ( -22 / +140)
Protection type IP 20
EN
