Zenox Zeus PRO Series User manual

Got your back on every mission
Zeus PRO Series
Gaming Desk
Installation Manual
www.zenoxstore.com/pages/assembly-guides
宙斯電競桌安裝指南
1. The product has to be used within the constraints of its
specifications.
2. We recommend installtion of desk by 2 adults, as some parts
are considerably heavy;
3. The desk is designed for regular desktop work only. Do not
use it as a stepstool or any other purposes;
4. Keep the product away from corrosive chemicals and dusty
environments;
5. Clean with gentle cleaners if necessary, and do not scrub
excessively;
6. All parts should be checked regularly to ensure the desk is
safe to use;
7. Stop using the product immediately if the table is found
damaged. Please check the maintenanace guide on our
website or contact us over the phone or via e-mail at
[email protected].

Table Top x 1 Lifting Columns x 2
BOX 01
BOX 02
*Slide the Lifting Columns
into the slot and affix to
the frame with the 4 M8
bolts.
Hex Keys x 1
Control Panel x 1
M4*8mm x 2
E
E
READY TO GO
步驟 步驟
重物
安裝開始
桌面 升降柱
Power Chord x 1
電源線 六角匙 控制面板
*把升降柱滑入固定孔卡槽，
並用4顆M8螺絲鎖在框架上.
M8*20mm x 4
M4*16mm x 2
2
2
*電競桌有一定重量，建議由最少2位成人移動.
*The desk is considerably heavy, and we
suggest moving by at least 2 adults.
廢物處理
警告
此標記表明該產品不應與其他生活垃圾一起處理.為防止未
經控制的廢物處理對環境或人類健康造成的危害，請以負責
任的方式進行回收，以促進物質資源的可持續再利用.丟棄本
產品時，請遵守您當地的環境法律和規程.
高度記憶設定
規格
升降柱段數: 3
最大負重: 100 KG
高度航程: 600 - 1230mm
輸入伏特數: 100 - 240V
最高速度: 38mm/s
運作溫度 °C: 0 - 40 °C
1. 使用 “▼”“” 按鈕調節至理想高度，例如70CM 高.
2. 按 “M” 儲存鍵直至 LED 控制面板顯示 “S-”, 然後再按 “1” 儲存現在
高度為第一個高度記憶. LED 控制面板 “S-1”代表設定完成.
3. 重複以上動作至“2” 跟 “3” 設定第二跟三高度記憶.
4. 如要返回已儲存高度, 按 “1”, “2” or “3” 一下, 桌子便會自動回到
自定高度.
1 6


E01 Overuse Protection Mode Allow system rest for 13 minutes
to prevent overheating.
E02 Overuse Protection Mode System is overheating. Allow
system rest for 25 minutes
before resuming useage.
E03/ Overload Protection Mode
E04
Reduce load applied should it
be above the recommended
value. Reset the system after
adjusment by holding the
“▼” button for 10 seconds.
E05 Motor 01 Protection Mode
E06 Motor 02 Protection Mode
Motor might be jammed.
Check and try resetting the
system after adjusment by
holding the “▼” button for
10 seconds.
E07 Motor 01 Single HALL
Malfunction
E08 Motor 02 Single HALL
Malfunction
Poor connection between
Motors and Control Box.
Check and try resetting the
system after adjusment by
holding the “▼” button.
E09 Imbalanced Desktop
Warning
Check for serious imbalance.
Reset system after adjusment
by holding the “▼” button.
E30 6 Axles Motion Sensor
Malfunction
Major malfunction. Please
contact manufacturer.
_OL Severe Overload
Protection Mode
Reduce load applied should it
be above the recommended
value. Reset the system after
adjusment by holding the
“▼” button for 10 seconds.
E20/ Motor Double HALL
E21 Malfunction
E22/ Motor 01 Power Supply
E23 and HALL Malfunction
Poor connection between
Motors and Control Box.
Check and try resetting the
system after adjusment by
holding the “▼” button
錯誤診斷碼一覽
E01 過度使用保護模式 暫停使用系統 13 分鐘，避免發生
過熱情況.
E02 過度使用保護模式 系統過熱， 暫停使用系統 25 分
鐘讓系統冷卻.
E03/ 負重超載保護模式
E04
減少負重到建議數值， 按著“▼”
10 秒鐘重置系統.
E05 摩打 01 保護模式
E06 摩打 02 保護模式
摩打可能受阻.
檢查及調整後長按 “▼” 10 秒鐘
重置系統.
E07 摩打 01 單 HALL 故障
E08 摩打 02 單 HALL 故障
摩打與控制盒信號出現問題.檢查
及調整後長按 “▼” 10 秒鐘重置
系統.
E09 桌面不平衡警告 檢查及調整負載不平衡情況.然
後長按 “▼” 10 秒鐘重置系統.
E30 6 軸動態感應故障 嚴重錯誤，請聯繫 本公司.
_OL 負重嚴重超載保護模式 減少負重到建議數值. 長按“▼”
10 秒鐘重置系統.
E20/ 摩打 雙 HALL 故障
E21
E22/ 摩打 01 供電及HALL 故障
E23
摩打與控制盒信號出現問題.檢查
及調整後長按 “▼” 10 秒鐘重置
系統.
3 4

Waste Disposal
Warning This marking indicates that this product should not be
disposed with other household wastes. To prevent
possible harm to the environment or human health
from uncoltrolled waste disposal, recycle it responsibly
to promote sustainable reuse of material resources.
Please follow your local environmental law and protocol
when dispose of this product.


Column Stages: 3
Max Loading: 100 KG
Height Range: 600 - 1230mm
Input Voltage: 100 - 240V
Max Speed: 38mm/s
Operating °C: 0 - 40 °C
1. Set the desk to a preferred height by using the “▼”“”
buttons, 70cm for instance.
2. Press the “M” SAVE button and the LED display shows “S-“,
then press “1” to save the 1st height position to 70cm. The LED
display shows “S-1”.
3. Repeat step 1 and Step 2 with “2” and “3” to save the 2nd
and 3rd height.
4. To recall saved settings, press “1”, “2” or “3”, and the desk
would automatically reposition to the saved height.
5 2
Accessories
步驟
3M Cable Holders
Phillips Head M3*6mm Bolts
Phillips Head M4*6mm Bolts
Shock Absorbers for Glass
Shock Absorbers for HDD
Shock Absorbers Bolt Ser for 2.5” SSD
Shock Absorbers Bolt Ser for 3.5” SSD
Lifting Columns Cable Cover
20 pcs
9 pcs
6 pcs
14 pcs
8 pcs
22 pcs
22 pcs
2 pcs
*移開電腦安裝板，裝上升降柱控制盒，再按指示插入電線
*Remove the mounting plate and install the control box. Plug in the cables accordingly.
*小心地把玻璃放到桌上
*Lower the glass onto the desk with care.
3
3
步驟
4
4
AC
HS M1 M2