Zest Santorini Swing 20772 User manual

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
V2
Assembly Instructions
Santorini Swing
(W x D x H) 1.90m x 1.50m x 1.80m
PLEASE KEEP THESE INSTRUCTIONS
Code: 20772
Online assembly video available
Please scan the QR code
CAUTION: CONSTRUCTION INVOLVES WORKING AT HEIGHT. SUITABLE EQUIPMENT REQUIRED.

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
IMPORTANT INFORMATION regarding
further treatment: Pressure Treated
products should not have any further
treatment applied for the first 6 months
A guide to understanding the natural characteristics of timber and what to do if you feel there is an issue...
If a particular split or crack becomes visible and is
of concern simply use the “2p Coin Test” as a guide.
ere is no need for concern if the coin will not fit. If
the coin does fit in the split, potentially there may be
an issue. In this case, in order for customer services
to investigate the matter fully, it should be reported in
writing to your retailer, along with a clear photograph
showing the 2p coin in place.
“Here at Zest we take any complaint very seriously
and each one is investigated individually and judged
specifically using established guidelines to determine
if it is a justified complaint and whether a replacement
part is required. “ Customer Service Dept.
Knots are a natural characteristic of timber however a dead
knot may be an issue which can be reported in writing to
your retailer and must include photographic evidence to
support the query.
Sun Bleaching
(from packaging)
& Green Spotting
(Caused by pressure
treatment) are not
causes for concern
and they will fade
over time when items
are placed outdoors.
Neither will affect
the durability of the
product.
Normal splits are
characteristics of timber.
Sun-bleaching & Pressure
Treatment green spotting
will fade in time.
Use the “2p Coin Test”
as a guide.
Knots are
characteristics
of timber.
If you find a dead-knot
email your retailer
including a photo.
Splits & cracks are to be expected in timber and they naturally
appear in the grain due to changing temperatures and humidity
levels . ey are not a cause for concern as they will not affect
the strength or durability of the product.
At Zest we are committed to the environment and we are very proud
to be a Forest Stewardship®Certified company. (FSC®C114990)
and all timber used has been ethically sourced from responsibly
managed forests.
Timber is a unique and naturally beautiful material with its
own characteristics which makes each piece distinctive.
FSC® Certified Products available on request
00273
For Product
Information

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
Santorini Swing Assembly Instructions
Santorini Swing Pack List
Item Description Quantity
A Horizontal Long Brace 2
B1, B2 Lower Leg (front) 2
C1,C2 Leg (back) 2
D Horizontal Short Brace 2
E1, E2 Upper Leg (front) 2
FTrellis Panel 2
G Swing Beam 1
H Diagonal Brace 2
J Canopy Support 2
K Canopy 1
L Centre Batten 1
M Seat Back 1
NSeat 1
OArmrest Support 2
P1, P2 Armrest 2
QShelves 2
RFixing Kit 1
Requires 2 Person assembly
Tools required: Corded / cordless drill, *Pozi- drive bit or Pozi-drive screwdriver (*Crosshead),
Socket set (13mm, 17mm & 19mm), Hammer and Mallet. Star Drive included.
Please take a few moments to check all pack contents listed
is product is made from pressure-treated timber. It should not be painted
or coated with any other treatment until at least 6 months after purchase

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
Santorini Swing Assembly Instructions
Fixings Quantity
30mm Screw 16
60mm Screw 42
80mm Screw 2
45mm Bolt, washer & nut 6
90mm Bolt, washer & nut 4
100mm Bolt, washer & nut 22
115mm Eye Bolt &, washer & nut 2
140mm Eye Bolt, washer & nut 2
170mm Eye Bolt & washer & nut 2
Small karabiner 6
Large karabiner 2
700mm Chain 2
900mm Chain 2
100mm Star Screw Drive 1

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
Set out Lower Leg (front) (B1), Upper Leg (front) (E1) and Leg (back) (C1) as shown (left) (large
holes face down) and place Horizontal Long Brace (A) and Horizontal Short Brace (D) in position
shown (Above left) Align bolt holes and insert 8 x 100mm Bolts. (Nuts & washers to be attached at
a later stage).
Note: horizontal short brace D has offset central hole which should be positioned closest to
rear leg C1.
Position Trellis Panel (F) between horizontal bracings and attach to Lower Leg (front) (B1) and Leg
(back) (C1) using 4 x 60mm screws.
Repeat procedure for remaining Lower Leg (front) (B2), Leg Back (C2), Upper Leg front (E2), Hori-
zontal Long Brace (A), Horizontal Short Brace (D) and Trellis Panel (F) to form right hand side of
swing.
1
Ensuring large drilled holes are facing up, attach Swing Beam (G) to Back Leg (C1) using 1 x
100mm Bolt, Nut & Washer. Do not fully tighten at this stage.
2

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
Attach Diagonal Brace (H) to Swing Beam (G) using 2 x 90mm Bolts, Nuts & Washers, and to
Horizontal Short Brace (D) using 1 x 100mm Bolt, Nut & Washer.
3
Attach other end of Swing Beam G to Back Leg C2 on previously assembled right hand side of
swing using 1 x 100mm Bolt, Nut & Washer.
4
5
Attach remaining Diagonal Brace (H) to Swing Beam (G) using 2 x 90mm Bolts, Nuts & Washers,
and to Horizontal Short Brace (D) using 1 x 100mm Bolt, Nut & Washer.

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
6
7
Ensuring Upper Legs (front) E1 & E2 are flush with underside of Swing Beam (G) (See above), fix
to Legs (back) C1, C2 as shown using 2 x 100mm Star Screws. (1 x Screw per leg).
All Nuts & Washers from Stage 1 onwards to be attached and fully tightened at this stage.
Attach Canopy Support (J) to Leg (back) (C1) using 1 x 100mm Bolt, Nut & Washer. Set at desired
angle and fix to Swing Beam (G) using 1 x 80mm Screw.

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
8
Insert 170mm Eye-Bolt into Swing Beam (G) as shown. Attach Washer & Nut and fully tighten.
Repeat procedure with remaining 170mm Eye-Bolt on other side of swing.
Set Canopy (K) out evenly on to Canopy Supports (J) and fix using 32 x 60mm Screws (2 x Screws
per slat, 1 x Screw at each end).
9
Insert Centre Batten (L) centrally beneath Canopy (K) and fix using 16 x 30mm Screws. (1 x Screw
per slat), working from front to back.

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
10
Note: Seat Back (M) on left. Seat (N) on right.
Interlock joints in Seat Back (M) and Seat (N), align bolt holes and secure using 6 x 45mm Bolts,
Nuts & Washers. (2 x Bolts per joint) do not tighten fully at this stage.

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
11
12
Align dowels in Armrest Support (O) with corresponding holes in Armrest (P1) and tap into
position. Fix in place using 1 x 60mm Screw.
Place Armrest Assembly on to Seat Assembly, align bolt holes and insert 1 x 140mm Eye Bolt into
Seat Back (M) and 1 x 115mm Eye Bolt into Seat (N). Attach Nuts & Washers and fully tighten.
Repeat Stage 11 for remaining armrest assembly on other side of seat assembly.
Fully tighten all nuts at this stage.

www.zest4leisure.co.uk | 01352 752555 option 1 | [e-mail]
13
Feed the long front chains through the holes in the Armrest Assemblies and attach pairs of chains
(long and short) to Small Karabiners and clip to Large Karabiners on Swing Beam Eye Bolts.
Place Shelves (Q) on to Horizontal Short Braces (D). Tap in with a mallet to fit.
Using 2 x Small Karabiners (1 x Per Eye Bolt), attach 1 x Short chain to rear Eye-Bolt and 1 x Long
chain to front Eye-Bolt. Repeat procedure on other side of seat.
Santorini Swing is now complete.