Zhejiang Jiajia Ride-On Co. AUDITT Datasheet

AUDI TT RS
BATTERY-POWERED RIDE ON
Owner’s Manual
with Assembly Instructions
Styles and colo(u)rs may vary.
Made in China.
The owner’s manual contains important safety information as well as assembly, use and
maintenance instructions.
The Ride-on Car must be assembled by an adult who has read and understands the
instructions in this manual.
Keep the package away from children and dispose of properly before use.
Keep this manual for future reference.

On the purchase of your new Ride-On.
This ride-on car will provide your child with many miles of riding of
enjoyment. To help assure you and your rider a safe ride we ask you to
please read this manual carefully, and keep it for future reference.
Follow the recommendations in this manual, they are designed to improve
the safety and operation of your ride-on car and it’s rider.
Battery
Charger
6V4 AH*1 6V7Ah*1 or 6V10 *1
6V500mA or 6V1000mA
6V4Ah*2 or 6V7Ah*2
12V1000mA
Suitable age:
Load Capacity:
Speed:
Size of car:
Power way:
Charge time:
37~96 Months
Under 30 kgs
1WD: 2.5 km/h 2WD:2.5~5 km/h
103 x 62 x 43.5 CM
Charging type
8 ~ 12 hours
About Your New Ride-On │1
VER: SMS-JE1198(TT RS)-EN-170520
Audi TT RS Electric Ride-on manufactured by Zhejiang Jiajia Ride-on
Co.,Ltd. (Address: Xincang Industrial Zone, Xincang Town, Pinghu City,
Zhejiang Province, China). Trademarks, design patents and copyrights
are used with the approval of owner AUDI AG.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
1
1
1
3
3
10
1
4
4
4
1
1
2
1
1
1
1
2
1
1
1
1
2
1
1
1
1
2
2
2
2
2
8
PART
NO.
REMARKS
PART NAME
Q’ty (pcs)
Vehicle body
Gear box
Driving wheel
Normal wheel
Bushing
Ø10 washer
Motor hood
Ø4x12 flat head screw
Lock nut
Hubcap
Steering column
Windshield
Mirror
Steering Wheel
M5x35 machine screw
Ø5 nut
Seat
M5x16 machine screw
Seat rest
Rear spolier
Split pin
Charger
Spanner
Remote controller
Ø5 nut
R/C driver
M5x22 machine screw
Placed on the steering wheel
Placed on the steering wheel
Left and right
One labeled “L”, and the other one labeled “R”
1WD
2WD
2WD
Parts List │2
IF EQUIPPED, for R/C type only
IF EQUIPPED, for R/C type only
IF EQUIPPED, for R/C type only

15
16
22
23
24 13
14
1
7
32
56
6
9
10
6
9
10
20 19
17 18
4
812
11
21
6
26
25 27
6
Parts Diagram │3
HINT: Some parts shown are assembled on both sides of vehicle
CONTROLLER STYLES MAY VERY
R/C Type
Normal Type

Before Assembly │4
• Make sure that the power switch is turned “OFF” before assembling the ride-
on.
• Before first time use, charge the battery for at least 4 to 6 hours.
• Assembly tools required:
WARNING!
Screwdriver
(not included)
Long nose pliers
(not included)
Spanner
●Non-rechargeable batteries are not to be recharged.
●Rechargeable batteries are to be removed from the toy before being charged.
●Rechargeable batteries are only to be charged under adult supervision.
●Different types of batteries or new and used batteries are not to be mixed.
●Batteries are to be inserted with the correct polarity.
●Exhausted batteries are to be removed from the toy.
●The supply terminals are not to be short-circuited.
BATTERY INFORMATION
• CHOKING HAZARD - Small parts. Not suitable for children under 36 months.
The product contains small parts, keep children away when assembling.
• ADULT ASSEMBLY REQUIRED.
• Always remove protective material and poly bags and dispose before assembly.

2
3
4
10
7
6
5
1
8910
Attach the Rear Wheels │5
Driving Wheel
Normal Wheel
1WD
Rear axle
Rear Bottom View
●Turn the vehicle body downside up.
●Remove all the parts from the rear axle.
1. Slide the gear box onto the rear axle (Left Side). Keep the motor and the connector on
the gear box through the larger hole on the rear vehicle and out where the battery sits.
2. Slide the driving wheel onto the rear axle. And keep the driving wheel match with the
gear box.
3. Slide the Ø10 Washer onto the rear axle.
4. Tighten a Lock nut to the end of the rear axle with a spanner.
5. Slide the Ø10 Washer onto the rear axle (Right Side).
6. Insert the bush into the hole in the center of the normal wheel.
7. Slide the Normal wheel onto the rear axle.
8. Slide the Ø10 Washer onto the rear axle.
9. Tighten a Lock nut to the end of the rear axle with a spanner. HINT: An extra
spanner has been provided to hold the Lock Nut on the other side of the rear
alxe while tightening the Lock Nut on the other side.
10. Fit the hubcaps to the wheel.
HINT: If your vehicle is Two Wheels Driving Type, see the next page please.

2
3
4
10
1
Attach the Rear Wheels │6
2WD
Driving Wheel
Rear axle
Rear Bottom View
●Turn the vehicle body downside up.
●Remove all the parts from the rear axle.
1. Slide the gear box onto the rear axle. “R” labeled gear box should be fit to the
“R” side of vehicle body; “L” labeled gear box should be fit to “L” side of vehicle
body. Keep the motor and the connector on the gear box through the larger
hole on the rear vehicle and out where the battery sits.
2. Slide the driving wheel onto the rear axle. And keep the driving wheel match
with the gear box.
3. Slide the Ø10 Washer onto the rear axle.
4. Tighten a Lock nut to the end of the rear axle with a spanner.
●Repeat the above procedure to assemble the other driving wheel.
●HINT: An extra spanner has been provided to hold the Lock Nut on the
other side of the rear alxe while tightening the Lock Nut on the other side.
5. Fit the hubcaps to the wheels.

1
2
3
4
5
6
Front axle
Attach the Front Wheels │7
Normal Wheel
Front Bottom View
Remove all the parts from the front axle.
1. Slide a Ø10 washer onto the front axle.
2. Slide a bush into the hole in the center of the normal wheel.
3. Slide the normal wheel onto the rear axle. And keep the normal wheel match
with the bush.
4. Slide a Ø10 washer onto the front axle.
5. Tighten a Lock nut to the end of the front axle with a spanner.
6. “Snap” the hubcap to the wheel.
Repeat the above procedure to assemble the other front wheel.

24
1
6
3
57
Attach the Steering Wheel │10
End of Steering column
●Turn the vehicle body over.
●Remove the M5x35 machine screw and Ø5 nut from the steering wheel.
5. Place the steering wheel over the steering column, protruding from the
middle of the steering wheel base.
6. Align the holes on each side of steering wheel with the holes at the end of
the steering column.
7. Fasten a nut on the opposite end of the screw to secure the steering wheel
to the steering column.
1. With a screwdriver remove the
screw on the battery cover
located in the center of the
steering wheel.
2. Remove the battery cover from
the top of the battery
compartment.
3. Insert two AA batteries in their
correct polarities.
4. Place the battery cover over
the battery compartment and
fasten with the screw you
removed in step one.
Attache the Steering Wheel
HINT: If the steering wheel of your vehicle equipped with the sound function,
please follow the steps 1~4 to add the batteries (Not Included), and refer to
the battery information on page 4.

4
5
1
3
2
2
Attach the Steering Column │8
Normaltype
Hole in the
front axle linkage
Front bottom view
●Turn the vehicle body on its side.
1. Slide a Ø10 washer onto the steering column from the straight end.
2. Insert the straight end of steering column up through the hole in the front of
vehicle body from bottom side, and out through the hole in the dash.
3. Insert the bent end of steering column through the hole in the front axle
linkage.
4. Fit a Ø10 washer onto the bent end of the steering column.
5. Insert a split pin into the hole in the steering column, bend the ends of split pin
back using a long nose pliers (not included).