ZIMX BK2 User manual

ZIM
M O V E M E N T
W I T H A T T I T U D E
.com
UKBIGBUY
Saving you money every day
BK2
HOVER BIKE
A T T A C H M E N T
H O V E R B O A R D S
W I T H A T T I T U D E

ZIM
H O V E R B O A R D S
W I T H A T T I T U D E
Operational Manual : BK2
BK2
HOVER BIKE
A T T A C H M E N T

This manual is designed to give you the information you need for the safe operation and maintenance of your
new ZIMX BK2 Hover Bike. Please read it thoroughly before riding your BK2 Hover Bike.
Section One of this manual involves safety and ZIMX BK2 Hover Bike. Understanding and following this
Information will help you and your ZIMX BK2 Hover Bike avoid injury or damage.
Section Two of this manual gives assembly and installation instructions for your ZIMX BK2 Hover Bike.
Section Three of this manual covers specic safety and operating instructions for your ZIMX BK2 Hover Bike.
Even if you are an experienced rider, you should review this section before your rst ride.
Section Four of this manual covers warranty specications of your ZIMX BK2 Hover Bike.
INTRODUCTION
WARNING
Make sure you read this complete manual before riding
your BK2 Hover Bike. Failure to do so, or failure to follow
its guidelines could lead to serious injury or death.
3

5
8
7
9
10
2
11
4
6
1
3
3
ZIMX BK2 HOVER BIKE DIAGRAM
SPECIFICATIONS
1. Seat
2. Handle Bars
3. Shock Absorbing Spring
4. Pedal Mounts
5. Hook and Loop Straps
6. Seat Frame
7. Adjustment knob
8. Frame Extension
9. Wheels
Compatibility: Most self-balancing electric scooters upto 10” wheels
Max Load: See max load of your self-balancing scooter
Max Speed: See max speed of your self-balancing scooter
Wheel Size: 8.5”
Seat Material: PU + Foam
4
6
10. Seat Pole
11. Foot Rest

55 > 80cm
adjustable
22cm
84 > 90cm adjustable
55cm
63cm
54cm
53cm
15cm
MEASUREMENTS
5

PARTS LIST
(1) Seat pole
(1) Seat Frame
(1) Frame Extension
(1) Wheels Bar
(1) Foot Rest
(1) Extension Tube
(1) Handlebar Rod
(1) Pedal Mount Frame
(1) Handlebar
6
NOTE - Some of the parts have been added to the product to reduce the steps required for assembly and reduce installation time.
(1) Seat

ACCESSORIES LIST
Set, 2 items
(2) Large Washer
(1) Spring
(1) Small Washer
(1) Wrench / Spanner
Tube
7
(2) Locking Nuts M10
NOTE - Some of the parts have been added to the product to reduce the steps required for assembly and reduce installation time.
Set
M6
M10
M8
M6
M10
M8
(1) Short Neck Plastic
Tube
(1) Long Neck Plastic
(2) Bolt Screw M10
(2) Wheel Frame Screws
(1) Adjustment Knob
(4) Rubber Pedal
Mount Ends
(2) Hook and Loop
Straps
(1) Allen key / Wrench
Set, 3 items

8
ASSEMBLING YOUR ZIMX BK2 HOVER BIKE
B
CA
Slide the frame extension into the A
extension tube then connect the foot B
rest with pre-installed (x2)nuts + long C
bolts and tighten with Spanner and Allen
key.
Connect the seat frame to the wheels bar and
using the wheel frame screws tighten together
using the allen keys.
On the tube of the pedal mount frame, add the
above accessories in order as shown here.
Next connect the seat frame to
the frame extension and tighten
with spanner and allen key, then
insert the adjustment knob.
2
1
34

Spring
Clip
Tighten
nut + bolt
7
5
6
Insert the
pedal mount
frame tube
on to the foot
rest.
Now insert the small washer, as per shown here.
Insert the into handle bar tube
the tube of the pedal mount
frame. Make sure the Spring Clip
Head within the tube of the
pedal mount frame is showing
through, as above. Using the
pre-installed nut + bolt tighten
with Spanners.
Loose and remove the
handlebar clamp at the top
of the handlebar rod, using
the allen key. Then insert the
handlebar, replace clap and
tighten securely with allen key.
ASSEMBLING YOUR ZIMX BK2 HOVER BIKE
9

Tighten
nut + bolt
8
Hover Bike is now complete.
ASSEMBLING YOUR ZIMX BK2 HOVER BIKE
Securely
tighten the
seat pole, using
the pre-installed
locking clamp.
Add the seat
onto the seat
pole and tighten
the seat clamp
using spanners.
Then insert the
seat pole into
the seat
frame.
10
Get ready to attach to your
self balancing scooter.

If you have questions or concerns about any of these steps, please feel free to contact our Customer Service
Team at www.ukbigbuy.com or www.zimx.uk Someone will be in touch to guide you through these steps.
Carefully follow the steps shown on the following pages for installing the ZIMX BK2 Hover Bike onto your
electric scooter. Read the remainder of this manual before riding your ZIMX BK2 Hover Bike.
Your ZIMX BK2 Hover Bike should be completely assembled prior to installing it onto your electric scooter.
Please refer to the “Assembling your ZIMX BK2 Hover Bike” section for assembling procedures.
- Place the pedal mounts onto the foot pedals of your self-balancing scoot er. Ensure the pedal mounts
are centered on the foot pedals of your scooter as much as possible.
INSTALLING YOUR ZIMX BK2 HOVER BIKE
- Place the ZIMX on your self-balancing scooter, and adjust the “adjustable metal brackets” BK2 Hover Bike
to t your scooter (if required) then fasten the nut tight, using the wrench/spanner provided.
sensor locations of self balancing scooter
where the 4 pressure rubber end bolts on the
hover bike’s pedal mount frame will make
contact with
adjustable
pedal mount
11

Rubber Pedal Mounts Ends
Slide on all the protective rubber pedal mount covers on each end of the pedal mounts. Then using the
through the holes on back of each pedal mount.
hook and loop straps, place the hook and loop side of strap downward and then pull each strap end
12

WARNING: Do not over tighten straps when you are assembling your ZIMX BK2 Hover Bike to your scooter.
Ensure that the ZIMX BK2 Hover Bike is secure to the scooter when attaching.
Your ZIMX BK2 Hover Bike should be properly installed onto your scooter as shown below.
13

ZIMX BK2 HOVER BIKE OPERATION
It is important that you fully understand all elements of your ZIMX BK2 Hover Bike . If these elements are not used
correctly, you will not have full control of your ZIMX BK2 Hover Bike . Before you ride fast, or outside of a controlled
environment, learn the functions of the various mechanisms on your ZIMX BK2 Hover Bike .
Practice using the elements of your ZIMX BK2 Hover Bike at slower speeds in at, open area before taking the
ZIMX BK2 Hover Bike to unfamiliar areas.
BEFORE RIDING
WARNING
Any scooter that does not work properly can cause you to
lose control and fall. Inspect the entire device thoroughly
before every ride, and do not ride it until any problems have
been corrected.
WARNING
Do not ride a ZIMX BK2 Hover Bike with a part that is
damaged; replace the damaged part before riding.
14

Ensure that your ZIMX BK2 Hover Bike and scooter are in proper working order each and every time you ride. If a
part of the ZIMX BK2 Hover Bike does not function correctly, please contact our Customer Support Center.
• Ensure your ZIMX BK2 Hover Bike is in perfect working order before riding it.
• Ensure the battery of your scooter is fully charged before riding your ZIMX BK2 Hover Bike .
• Ensure that all the screws and nuts on the ZIMX BK2 Hover Bike are locked rmly before each ride.
• Check to ensure the tyres of your scooter are not worn.
• Check to ensure all connections are maintained on your scooter.
PRE-RIDE ZIMX BK2 HOVER BIKE CHECKLIST
15
To reduce the risk of injury, adult supervision is required.
Never use in roadways, near motor vehicles, on or near
steep inclines or steps, swimming pools or other bodies
of water; always wear shoes, and never allow more
than one rider.
WARNING:

SAFETY PRECAUTIONS
The 1st rule in safe riding is to use common sense. A ZIMX BK2 Hover Bike is vulnerable; it cannot protect you in a
crash, against impact, or loss of control the way driving a car can. A ZIMX BK2 Hover Bike can tip over sideways
so be vert careful. It moves faster than a typical scooter. It does not have bumpers or airbags as a car does. This
section is a guide of safe riding practices for operation. Make sure you are using your ZIMX BK2 Hover Bike properly.
Different localities and countries have different laws governing riding in public places, and you should check with
local laws to ensure you are complying with them.
ZIMX or UKBIGBUY is not liable for tickets or violations given to riders who do not follow these regulations.
• For your safety, always wear a helmet that meets CPSC or CE safety standards. In the event of an accident, a
helmet can protect you from serious injury and in some cases, even death.
• Hover Bikes and Hover boards are not transportation vehicles.
• Do no use on public roads. Obey all local laws.
• Ride defensively; expect the unexpected.
• Do not ride too close to other riders and alert them if you intend to pass them from behind.
16
• If riding with friends and multiple ZIMX BK2 Hover Bikes, ride single in a straight line.
WARNING!!
It is illegal to ride electric scooters or self balancing scooters on public roads, pavements, or cycle paths.
They are intended only for use on private land with the owner's permission.

.
• Avoid potholes, drainage grates or other hazards.
• Be careful when riding on soft road edges, gravel, sand and uneven surfaces. Ride slowly and avoid quick turns
when riding on these surfaces.
• Never hitch onto other vehicles.
• Do not “stunt” ride or race on uneven surfaces.
• Do not weave in and out of traffic or swerve from side to side.
• A crash can put extraordinary stress on ZIMX BK2 Hover Bike components, possibly causing them to fatigue
prematurely. Components suffering from stress fatigue can fail suddenly, causing loss of control or serious injury.
CAUTION: RIDING IN WET WEATHER
Brakes do not work as well under wet conditions as they do when dry. It is recommended that you do not ride your
ZIMX BK2 Hover Bike in wet weather, as there are electronic components in your scooter that may be damaged
if exposed to water.
17

1. This product is strictly forbidden to use on roads, pavements, cycle paths, motorways. You must wear a safety
helmet, knee and elbow pads and other necessary protective gear when riding your ZIMX BK2 Hover Bike.
2. Due to the particularity of the product, the assembly pieces are to be checked before every ride to avoid an
accident while riding.
3. Do not make a sharp turns as you may drift and overturn the ZIMX BK2 Hover Bike which can result in injury to
yourself and/or damage the unit.
To reduce the risk of injury, adult supervision is required.
Never use in roadways, near motor vehicles, on or near
steep inclines or steps, swimming pools or other bodies
of water; always wear shoes, and never allow more
than one rider.
WARNING:
18

RIDING YOUR ZIMX BK2 HOVER BIKE
Ensure your ZIMX BK2 Hover Bike is fully assembled and correctly installed onto your scooter with all straps and
bolts / screws and nuts secured in place. Ensure your scooter is properly maintained as well. Failure to do
so may result in serious bodily harm or death and damage to the unit.
After reviewing the pre-ride checklist, follow the steps below to begin riding your ZIMX BK2 Hover Bike.
1. Turn on your scooter.
2. Sit comfortably in the ZIMX BK2 Hover Bike seat.
2. Place your feet onto the foot rest, and keep them there at all times when riding.
3. Firmly grip handle bars and slowly push it forward to move forward.
4. When riding, slowly pull handle bar backwards to brake.
5. To reverse, slowly pull handle bar backwards.
6. To turn left, turn the handle bar left, as you would do when riding a bike.
7. To turn right, turn the handle bar right, as you would do when riding a bike.
19