654321
654321
SERVICE
IR OUT
DC IN
HDMI IN
HDMI IN
AUDIO Pr Pb Y
R
LHDMI OUT
1
2
HDMI IN
HDMI IN
3
4
Place the two AAA batteries into the remote control.
Part 5 Remote Control Unit Instruction
ZRC-0000
DOLBY
DIGITAL
POWER
EXIT
MENU
SELECT
DC IN
IR IN
SERVICE
HDMI OUT
IR Sensor Extender cable
High Def. Flat-panel TV
IR Blaster Extender cable
If the Infrared (IR) Blaster & Sensor (included) are connected to the BV-2822T
and BV-2822R so you can point hand-held remote controls ofyour HDA/V
equipment at the BV-2822R (receiver) orat yourHDTV insteadof at theA/V
equipment. The transmission distanceis 66 feet, line-of-sight.
Part 4 IR Blaster and Extender Setup
Y/Pb/Pr
Video
RGB
S-Video
HDMI
DC IN HDMI OUT
IRIN
SERVICE
Part 6 Operation
Press the POWER button on the remote
control oron the top of the BV-2822R
and BV-2822T to turn onthe transmitter
and receiver when both POWER LEDs of
transmitter andreceiver are lit in red.
Power onyour TVset and go to the
source menu under the settings menu
of your HDTV set.
Then select theHDMI input to which
the BV-2822 receiver isconnected.
Press the SOURCE button on the remote control
or on thetop of theBV-2822R (receiver)to select
the input source, until available video/audio is
shown on theTV screen. If all operation is
normal, the POWER LED andSOURCE LED will be
lit in solidblue, and the user can press the INFO
button on the remotecontrol tocheck the status
of signal qualityand A/V source selected.
Note :
The wireless linkmight require 80 seconds toconnect
between transmitterand receiver, and showvideo on
the TV screen.Please be patientand wait fora while.
Activate the BV-2822
and Set up the Link
Part 7 Limited Warranty
If you have electronicdevices such as cordless phones, wireless AC points/routers operating in the 5GHzband and nearthe
BV-2822, the audio/video quality onthe display or TV may suffer. Pressthe "CHANNEL" button twice on the remote control
to switchto an appropriate channel for the BV-2822.
NOTE:
Internet
Button
POWER
INFO.
SOURCE
CHANNEL
WIDE
(1080i content only)
FunctionDes cription
Press to turn the BV-2822 Transmitter/
Receiver on/off. User need to pointing at
BV-2822T & BV-2822R both to boot
up when both POWER LEDs lit in red.
Press to display "Channel","Source",
"Resolution","WIDE mode" and ' Signal
Quality'
Press this button to switch audio/
video sources connected to the
BV-2822T.
Press this button to change wireless
channels manually if the user
experiences video noise.
Press this button to enable the "WIDE"
mode to boost transmission distance.
Up to 100 feet (1080i content only)
Operation
Press to go to the next input source.
Users can see the current setting on the OSD.
Pressonc e todispl aythe current"Channel" status.
Pressagai n within 5 secondsto switch toanoth erchan nel, and
thecha nnel numberwill bedispl ayed onthe OSD.
Pressthisbutto n toenab le anddisa bleWid e mode.
Pressagai n within 5 secondsto enable WIDEmod e, andthe
statuswillbe displayedonthe OSD.
Press it pointing at the BV-2822R to enter the "Standby
Mode" and the loop-through connection is on; press
it when pointing at the BV-2822T to enter the "Standby Mode
" and the loop-through connection is off.
Pressonceto display thecurr entstat us.Pres s againto exit OSD.
During INFO. OSDdispla yed, pressSOUR CEbutt onto adjust
thecloc k phaseif necessary.
IBXXXXXXX Rev.0
Blu-ray Player or High-Def Set-top Box or High-Def Game Console
This limited warranty (hereinafter the Warranty) is valid for the BV-2822 (hereinafter the Product). The Warranty is only valid in the country where the Product
was originally purchased.
The Warranty only covers manufacturing defects, and excludes defects caused by the inappropriate use or storage of the Product.
The Warranty is issued by Xpike Innovation. Inc. to the end purchaser (hereinafter the Customer) of the Product.
In accordance with the Warranty, the Customer has a sole claim to demand repair or replacement of the Product but may not assert claims or seekcompensation again
st the manufacturer/retailer for further losses (including, but not limited to, the indirect loss of data or profit).
The Warranty provides coverage over a period of 12 months, commencing from the initial purchase date of the Product by the Customer of Xpike Innovation. Subsequent
changes of ownership do not extend the warranty period.
The Warranty is valid with the proviso that the Product is shipped to Xpike Innovation within the warranty period. In the event of any faults or defects with the Product,
it must be shipped back to Xpike Innovation. Products will be repaired or exchanged at Xpike Innovation's own discretion. The warranty period is not extended for any
repaired or replaced Products. Exchanged parts are the property of Xpike Innovation .Inc.
The Warranty is valid solely on the condition that the original proof of purchase issued is presented with the Product.
, the brite-View logo, are trademarks of Xpike Innovation Inc., registered in USA.
For detailed operating instructions, please visit to download the user manual.www.brite-view.com
