Zinwell WHD100 User manual

0

1
Table of Contents
TABLE OF CONTENTS.............................................................................................................1
1. IMPORTANT INFORMATION..............................................................................................2
2. INTRODUCTION.................................................................................................................7
2.1 PACKING CONTENT .........................................................................................................7
2.2 OVERVIEW ....................................................................................................................8
2.2.1 TRANSMITTER ........................................................................................................8
2.2.2 RECEIVER ..............................................................................................................9
3. INSTALLATION .................................................................................................................10
STEP 1: SETUP THE TRANSMITTER..........................................................................................10
STEP 2: SETUP THE RECEIVER ................................................................................................ 11
STEP 3: BOOT UP THE TRANSMITTER AND RECEIVER..................................................................12
STEP 4: MOUNTING THE RECEIVER TO THE WALL .....................................................................16
4. TROUBLESHOOTING........................................................................................................17
5. SUPPORTED RESOLUTION...............................................................................................18
6. AUDIO BIT RATE SUPPORT..............................................................................................19
7. PRODUCT SPECIFICATION ...............................................................................................20

2
1. Important Information
Please take the time to read this user manual
before using the WHD100.
It contains important information about
operating your video wireless kit.
Our company’s limited warranty applies when
the product is handled properly for intended use,
in accordance with its operating instruction.
However, the warranty may be void in the
following cases:
Repair, product modification or alteration
have been performed by unauthorized
service personnel
Damages caused by accidents, including
but not limited to, lightning, water, fire, or
moisture
Use of an AC adapter not compatible with
the product and its voltage rating
The model number on the product has
been altered, deleted, removed or made
illegible.
Safety Precautions
WARNING!
RISK OF
ELECTRICAL
SHOCK
DO NOT OPEN
WARMING:
TO REDUCE THE RISK OF ELECTRICAL SHOCK
DO NOT REMOVE THE COVER
NO USER-SERVICEABLE PARTS ARE INSIDE
REFER SERVICING TO QUALIFIED
PERSONNEL
Danger: Be careful with electricity.
Power to the units must be switched off
before any work is undertaken, such as
any AV device connection or TV
connection.
Power outlet: To prevent electric shock,
make sure to use the appropriate AC
adapters as power supply to the
transmitter and the receiver.
Power cord: Be sure the power cord is
routed so that it will not be stepped on or
pinched by heavy items.
Power overloading: Avoid overloading
electrical outlets or extension cords which
otherwise could result in electric shock or
fire.
Lightning: Disconnect the product from
the power source if it is left unattended
for a long period of time, and to protect
the product from lightning.
Always disconnect the power cord from
the power outlet when you are not using
your Full HD Video wireless kit. This
reduces the risk of electric shocks or fire.
Warning
This product should not be exposed to
dripping or splashing. No object filled
with liquids, such as vases, should be
placed on the product.
Object Entry: To avoid electric shock,
never stick anything in the slots on the
case or remove the cover.
Place receiver/transmitter on a flat, hard
and stable surface
Ventilation: Do not block the ventilation
slots on the receiver/transmitter or place
any heavy object on the top cover.
Blocking the air flow could damage the
receiver. Arrange components so that air
can flow freely around the receiver.
Ensure that there is adequate ventilation
if the receiver is placed in a stand.
Put the receiver/transmitter in a property
ventilated area, away from direct sunlight
or any source of heat.
Water Exposure: To reduce the risk of fire
or electric shock, do not expose the
receiver/transmitter to rain or moisture.
This is indoor solution.
Our company has the right to modify this
document without any notice.

3
Special Notice
Never use this product nearby an aircraft
or medical facility. It can cause
interference or undesirable effect on the
operation result.
Use of this product in the following
locations may result in abnormal video
and audio output (noise, blocked image...
etc,).
Product installed in the walls made
of concrete.
Product is situated near the
refrigerator or metal fitment.
A cluttered room where the
wireless signals may be blocked
This product has been tested and
manufactured to comply with each
country’s safety rules. However, there is
no guarantee that interference will not
occur in some installation scenario. If the
interference happens, increase the
distance between the transmitter and
receiver.
WHDI DEVICE may interfere 5GHz
wireless devices, such as routers or other
wireless devices. Therefore, if you have an
802.11n router, configure it to the 2.4
GHz band rather than the 5GHz band.
Optimal range between WHDI DEVICE
transmitter and receiver is between 2 and
20 meters within line of sight.
Europe – EU Declaration of
Conformity
This device complies with the essential
requirements of the R&TTE
Directive2014/53/EU. The following test
methods have been applied in order to
prove presumption of conformity with
the essential requirements of the R&TTE
Directive 2014/53/EU:
EN55032
Electrowagnetic compatibility of multimedia
equipment-Emission requirements
EN 55022 Information technology
equipment----
Radio disturbance characteristics--- Limits
and methods of measurement
EN 61000-3-2 Electromagnetic compatibility
(EMC)---
Part 3-2:Limits---Limits for harmonic current
emissions (equipment input current up to
and including 16 A per phase)
EN 61000-3-3 Electromagnetic compatibility
(EMC)---
Part 3:Limits---Section 3: Limitation of
voltage changes, voltage fluctuations and
flicker in public low-voltage supply systems,
for equipment with rated current ≦16 A per
phase and not subject to conditional
connection
EN 55024 Information technology
equipment----
Immunity characteristics---Limits and
methods of measurement
EN 60065 Audio，video and similar
electronic apparatus—Safety requirements
DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any interference
received, including interference that may
cause undesired operation.
This Class B digital apparatus complies
Canadiàn ICES-003. Cet appareil numérique
do la class B est conforme à la norme
NMB-003 DU Canada.
EMI (Electro Magnetic Interference) tested.
TRADEMARK INFORMATION
HDMI, the HDMI Logo and
High-Definition Multimedia Interface
are trademarks of HDMI Licensing LLC.

4
EN 60065: 2014/AC:2016
Audio,VideoandSimilarelectronic
apparatus
EN 62479:2010
Assessments of the compliance of
Low-power electronic and elect cal
equipment with the basic restrictions
related to human exposure to
electromagnetic fields (10MHz to
300GHz).
EN 50385:2002
Product standard to demonstrate the
compliances of radio base stations and
fixed terminal stations for wireless
telecommunication systems with the
basic restrictions or the reference levels
related to human exposure to radio
frequency electromagnetic fields
(110MHz - 40GHz). General public
EN 301 893 V1.8.1: 2015
Broadband Radio Access Networks
(BRAN); 5 GHz high performance RLAN;
Harmonized EN covering essential
requirements of article 3.2 of the R&TTE
Directive
EN 301 489-1 V1.9.2: 2011
Electromagnetic compatibility and Radio
Spectrum Matters (ERM); Electro
Magnetic Compatibility (EMC) standard
for radio equipment and services; Part 1:
Common technical requirements
EN 301 489-17 V2.2.1 2012
Electromagnetic compatibility and Radio
spectrum Matters (ERM); Electro
Magnetic Compatibility (EMC) standard
for radio equipment
Part 17: Specific conditions for Broadband
Data transmission systems
FederalCommunication
CommissionInterferenceStatement
This device complies with Part 15 of
the FCC Rules. Operation is subject
to the following two conditions: (1)
This device may not cause harmful
interference, and (2) this device
must accept any interference
received, including interference that
may cause undesired operation.
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one of the following
measures:
Reorient or relocate the receiving
antenna.
Increase the separation between
the equipment and receiver.
Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
Consult the dealer or an
Hereby, Zinwell declares that this Full HD
Video wireless kit is in compliance with the
essential requirements and other relevant
provisions of Directive2014/53/EU

5
experienced radio/TV technician
for help.
FCC Caution: Any changes or
modifications not expressly approved by
the party responsible for compliance
could void the user's authority to
operate this equipment.
This transmitter must not be co-located or
operating in conjunction with any other
antenna or transmitter.
RadiationExposure
Statement(Transmitter):
The product comply with the FCC portable
F exposure limit set forth for an
uncontrolled environment and are safe for
intended operation as described in this
manual. The further RF exposure reduction
can be achieved if the product can be kept
as far as possible from the user body or set
the device to lower output power if such
function is available.
The USB dongle transmitter is approved for
use in typical laptop computers. To comply
with FCC RF exposure requirements, it
should not be used in other devices or
certain laptop and tablet computer
configurations where the USB connectors
on the host computer are unable to
provide or ensure the necessary operating
configurations intended for the device and
its users or bystanders to satisfy RF
exposure compliance requirements.
Receiver should be installed and operated
with minimum distance 20cm between the
radiator & your body.
RadiationExposure
Statement(Receiver):
This equipment complies with FCC
radiation exposure limits set forth for an
uncontrolled environment. This
equipment should be installed and
operated with minimum distance 20cm
between the radiator & your body.


IndustryCanadastatement:

This device complies with ISED’s licence-exempt Ross. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas
produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Note:Thecountrycodeselectionisfornon-USmodelonlyandisnot
availabletoallUSmodel.PerFCCregulation,allWiFiproductmarketedin
USmustfixedtoUSoperationchannelsonly.

6
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and
5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be
such that the equipment still complies with the e.i.r.p. limits pecifiedforpoint-to-point and
non-point-to-point operation as appropriate; and
(iv) Users should also be advised that high-power radars are allocated as primary users (i.e.
priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars
could cause interference and/or damage to LE-LAN devices.
Avertissement:
Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions
précises sur les restrictions susmentionnées, notamment :
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 à 5350
MHz et de 5470 à 5725 MHz doit être conforme à la limite de la p.i.r.e;
(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5850
MHz) doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et
l’exploitation non point à point, selon le cas;
(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de
haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les
bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du
brouillage et/ou des dommages aux dispositifs LAN-EL.
RadiationExposureStatement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclarationd'expositionauxradiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.

7
2. Introduction
WHD100 is a Full HD wireless transmission device.
This solution delivers uncompressed 1080p full HD video and audio content to your existing HDTV
set wirelessly. It operates the transmission in 5.1 GHz~ 5.9 GHz frequencies and it can adjust its
communication frequency automatically in case of interference from another RF system. With
built-in Omni-directional antennas, it can transmit uncompressed video content to 7 meters (20 feet)
LOS (Line of sight) with no latency.
2.1 Packing Content
Please check whether the following items are present in the package. If any items missed or
damaged, please call your dealer.
WHD100T
WHD100R
USB cable HDMI cable
Mini USB Power Adapter
Quick Installation
Guide
Anchors x2
Sc
r
e
w
s
x2
Mini USB Power Adapter

8
2.2 Overview
2.2.1 Transmitter
Lateral view
Top view
LED Status Indicator
The LED indicator is lit solid
blue when the power is on
and wireless link
DC IN
Connect to transmitter's Power
adapter
HDMI IN
Plug in transmitter to any
source device that have
an HDMI port directly.
Pairing button
The button reserved for
multiple transmitter &
receiver pairing usage.

9
2.2.2 Receiver
Top view
Rear view
Power Button with LED
indicator
Press to turn the receiver on and
off. The indicator in the power
button lights up in blue when
the power is on, and turns red in
standby mode.
Status LED
Display the video status
information.
HDMI OUT
Connect to HDTV set via an HDMI cable.
DC IN
Connect to receiver’s
p
ower ada
p
ter.
IR IN
Connect to IR Sensor extended cable.
USB HID
Support USB HID function for Keyboard/mouse usage.
INFO. Button
Press this button for OSD
displayed the information on
the HDTV screen.