Zip Hydroboil HS010 User manual

Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03 Page 1 of 12
Installation and Operating Instructions
Zip Hydroboil
Instant boiling water
HS010 Hydroboil 10 Litre White 10552
HS110 Hydroboil 10 Litre Stainless Steel 10551
HS015 Hydroboil 15 Litre White 11552
HS115 Hydroboil 15 Litre Stainless Steel 11551
HS025 Hydroboil 25 Litre White 12552
HS125 Hydroboil 25 Litre Stainless Steel 12551
HS040 Hydroboil 40 Litre White 04552
HS140 Hydroboil 40 Litre Stainless Steel 04551
®

Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03 Page 2 of 12
Installation Checklist
Description
Before Installation:
A. Read the instructions.
B. Note:Allttingsaresuppliedwiththeappliancekitexceptisolationvalveand
 pressurereductionvalve,whicharenotsupplied.
C. Checkthewaterqualitytodetermineifextraltrationwillberequired.Apotable
 mainswatersupplymustbeused.
 Tocombatthebuildupoflimescale,ahighperformanceinlinelter(notsuppliedas
 standardequipment)maybeorderedfromyourZipserviceprovider.(SeeProduct
 Accessoriespage4)
D. Checktheapplianceratingplateandensurecorrectpowerisavailableforthe
appliance.
E. Checkthewallsupportingtheapplianceisadequateforthetotalweightofthe
 appliance,whenfullofwater.
Before Commissioning:
1. Checktheunithasbeeninstalledcorrectly.
2. Checkallplumbingttingshavebeentightened.
3. Ensure the vent pipe is positioned to drain correctly.
4. Checkallelectricalconnectionsarecorrectandtherearenoloosewires.
Commission:
7. Flush the supply line before connecting.
8. Turnonthewater,allowtollandcheckforleaks.
9. Turnonthepower.
WallmountedOver-sinkapplianceforinstantboilingwater.
Features:
• Designedtooperatewithin1°Cofboilingpoint.#
• Temperaturecontrolsautomaticallycutoffthepowerintheeventoftemperature
controlfailure,boildrycutoutorablockedventpipe.
• Incorporatingapulldowntapforprecisionfillingofcups,italsolocks‘ON’forfilling
pots.
• Separatesthecoldwatersupplyfromtheboilingchamberandtheinternal
condensingsystemretainssteamwithintheheater.
• Astainlesssteelcrevicefree,boilingchamberwithserviceaccessportstopand
bottom.
• Hightemperaturethermalinsulationwithprovisionforserviceaccesstotheboiling
chamber.
• Concealedplumbingandelectricalconnections.
• Choiceofstainlesssteelorwhiteenamelledsteelcase.

Page 3 of 12 Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03
Product Specifications / Accessories...........................................................................................................................4
Read These Warnings First ..................................................................................................................................... 4 - 5
Installation Requirements.............................................................................................................................................5
Installation Procedures ........................................................................................................................................... 6 - 8
Step 1 – Positioning.................................................................................................................................6
Step 2 – Fastening...................................................................................................................................6
Step 3 – Connecting ................................................................................................................................7
 a)Plumbing................................................................................................................................7
 b)Venting...................................................................................................................................7
 c)Electrical ................................................................................................................................7
Step4–Assembling................................................................................................................................8
Tap Fitting..................................................................................................................................8
Step5–Commissioning .........................................................................................................................8
Operating Procedures ..................................................................................................................................................8
Wall Mounting Template Dimensions ..........................................................................................................................9
Earth Continuity Verification / Wiring Diagram.........................................................................................................10
Problem Solving...........................................................................................................................................................10
Maintenance ................................................................................................................................................................10
End of life disposal......................................................................................................................................................10
Spare Parts ..................................................................................................................................................................11
Warranty / Contact Details..........................................................................................................................................12
Contents
NOTE:
Read all instructions and precautions before proceeding. If in doubt, or need further guidance, please call Zip on 0845 6 005 005.
Pleaseleavetheseinstructionswiththeenduserafterinstallation.
Thisunitmustbeinstalledinaccordancewithwatersupplybyelaws,currentIEEregulationsandrelevantlocalauthority
byelaws.
TheseproductsareapprovedtotheLVDandEMCdirectivesandCEendorsed.
ZipHydroboilhasbeenexamined,testedandfoundwhencorrectlyttedtocomplywiththerequirementsoftheUnited
KingdomWaterRegulations/Byelaws(Scotland).TheproductsarelistedundertheWRAS(WaterRegulationsAdvisory
Scheme)WaterFittingsandMaterialsDirectory.
ZipHeaters(UK)Ltdcannotbeheldliableforanydamagescausedbyfailuretoobservetheseinstructions.

Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03 Page 4 of 12
Accessories:
Inline Filter
FL104 10”(Fortasteandodourremovalwithscalereduction)
Drip Tray
ZD001 StainlessSteel(withdrain)
ZD002 StainlessSteel(nodrain)
Cup Dispenser
ZE001 Stainless Steel
ZE002 White Plastic
ZE010 MugRack
Tundish
ZD100 WallMountedChromeTundish
ZD101 SinkMountedChromeTundish
Water Block
HE45004Recommended;ttedintothesupplylinetominimisepotentialdamageintheeventofleakage.
Pressure Reducer
AQ3 Combinedpressurereducer(setat3.5bar)andlinestrainer.
Read These Warnings First
WARNING: Situations that could cause injury to yourself or others.
CAUTION: Situationsthatcouldcausedamagetoyourapplianceorotherequipment.
NOTE: Notes,usagetipsoradditionalinformation.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY.
NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO
SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.
RETAIN THESE INSTRUCTIONS FOR FUTURE USE.
Model Finish Capacity
Litres
Delivery
Cups @ any
onetime
Recovery
Cups per
hour
Rating
kW@
230V
Width
mm
Depth
mm
Height
mm
Weight
Empty
Kg
Weight
Filled
Kg
HS010 White 10 60 180 3.0 390 244 600 15.0 29.5
HS110 s/steel 10 60 180 3.0 390 244 600 15.0 29.5
HS015 White 15 90 180 3.0 390 299 600 16.0 34.5
HS115 s/steel 15 90 180 3.0 390 299 600 16.0 34.5
HS025 White 25 150 180 3.0 390 299 780 19.0 47.0
HS125 s/steel 25 150 180 3.0 390 299 780 19.0 47.0
HS040 White 40 240 360 2x3.0 515 284 840 25.0 71.0
HS140 s/steel 40 240 360 2x3.0 515 284 840 25.0 71.0
Water Inlet Pressure: 0.07MPa(0.7bar)minimum/0.7MPa(7bar)maximum. Protection class IP23
Product Specifications

Page 5 of 12 Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03
Safety
Thisapplianceisnotintendedforusebypersons(includingchildren)withreducedphysicalsensory
ormentalcapabilities,orlackofexperienceandknowledgeunlesstheyhavebeengivensupervision
or instruction concerning use of the appliance by a person responsible for their safety.
Childrenshouldbesupervisedtoensurethattheydonotplaywiththeappliance.
Pleasereadallinstallationrequirements,installationproceduresandprecautionsbeforeinstallingany
ZipHydroboilinstantboilingwaterheater.
NeverattempttoinstallanyZipHydroboilinstantboilingwaterheaterwithoutreadingalloftheapplicableinstructions.
Careshouldbetakentoavoidtouchingthemetalbodyofthetapwhichcanbecomeveryhot.
InsomehardwaterareaswheremineralscaleaccumulationintheboilingchamberoftheZipHydroboilmaybecome
aproblem,considerationshouldbegiventothemaintenancerequired.Asuitableformofwatertreatmentmaybe
necessary.
Astheinstaller,itisyourresponsibilitytosupply(ifnecessary)andinstallallvalvesasrequiredbylocalregulationsand
relevant standards.
TheplumbinginstallationmustbedoneinaccordancewithlocalWaterAuthorityregulationsandtheseInstallation
Instructions.
Read These Warnings First Cont.
This appliance must be earthed.
Ifthepowercableisdamageditmustberepairedonlybyaqualifiedtechnician.Toavoidhazards,allinstallation
proceduresmustbecarriedoutbyasuitablyqualifiedtradesperson.Thepowercableandpoweroutletmustbeinasafe
visible position for connection.
Thepowercablemustbeadequatelysecured.
Donotremovethecoveroftheheaterunderanycircumstanceswithoutfirstisolatingtheheaterfromthepowersupply.
Theappliance,itswiringandpipingmustnotbemodiedinanyway.
Theappliancemustbecompletelylledwithwaterbeforebeingswitchedon.
Incaseofmalfunctionisolatethepowersupplyimmediately.Incaseofleaksalsoisolatethewatersupply.Repairsmust
onlybecarriedoutbyZipHeaters(UK)LtdoranauthorisedZipserviceengineer.
Lifting
TakecarewhenliftingtheZipHydroboilunit.Someunitsmayexceedsafeliftinglimits.Ifyoufeelthisisbeyondyour
personalcapabilities,pleaseseekassistancewiththelift.Seespecificationsonpage4forweights.
Operating Conditions:
Theambienttemperaturesthisunitshouldoperatewithinis5ºC-50ºC.
Frostprotection:Ifthisheaterislocatedwhereambientairtemperaturecouldfallbelow5ºC;whentheheaterisnotin
use,donotturnofftheapplianceelectrically.Thissafeguardwillprotecttheunitfromfrostdamagebutdoesnotoffer
thesameprotectiontotheconnectingpipeworkandfittings.
Thisheaterisintendedonlyforindooruseandshouldneverbeinstalledoutdoorsorbeexposedtotheelementsofnature.
Thisunitmustnotbepositionedinanareathatmaybecleanedbyawaterjet.Thisunitmustnotbecleanedbyawaterjet.
Cleaning:
Hydroboil should only be wiped clean with a damp cloth. Never use abrasive cleaning agents or solvents on any
part of the Hydroboil, particularly the tap.
Installation Requirements
Beforeinstalling,ensurethatthefollowingareavailable:
a. Sufficientspacetopositiontheheatersothereisatleast150mmclearanceabovetheheaterforserviceaccess,
65mmtoitsleftand20mmtoitsright–thetapoutletusuallyshouldbepositionedatleast200mmabovea
draining board or drip tray.

Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03 Page 6 of 12
Before you begin
Locatethepapermounting-holetemplatepackedwiththeheater.
Readtheinstallationandoperatinginstructionscompletely.
Decidewhethertoinstallwithconcealedorexposedplumbingand/or
electrical connections. Concealed connections are preferred for a superior
appearance.
Iftheheaterisusedforfillingcups,theninserttheflowrestrictorintotheoutlet
pipebeforesecuringtapassembly.
Step 1 - Positioning
Positiontheheatersothetapwilldrainontothedrainingboardordriptray.
Positionthebaseofthetaptobenotlessthan200mmabovethedraining
board.(Heightshouldbeincreasedonlyifitisessentialtoaccommodate
largervessels.)
Minimumclearancesforserviceare150mmtop,65mmleftand20mmright.
Markcornerpositiononwallsotopositionmounting-holetemplate.
Step 2 - Fastening
Positionmounting-holetemplateonthewallanddrillmountingholeswhere
shown.
Drillholesforwaterinlet,ventoutletandwiringifitisintendedtoinstallthe
heaterwithconcealedelectricalandplumbingconnections.
Removecoverfasteningscrewsandliftcoverawayfromchassis.
Installplumbingandwiring,andpreparepipeendsforconnectionasshownin
step 3.
Screwheaterchassistothewallusingthesuppliedfixings, ensurethefixings
aresuitableforthesubstrate.Ifnotsupplyyourownsuitablefixings.
Ensurethemountingsurfaceiscapableofsupportingtheweightofthefilled
unit,fixingsmustbecapableofsupportingtheheaterweightwhenfilled.
See chart on page 7.
Installation Procedures
COLD
INLET
VENT
OUTLET
INLET
POSITION
VENT
POSITION
Front View
b. Electrical supply.
Astandard13ampdoublepolefusedspuronthewallwithin1500mmofthe
heater.
Isolationswitchesmusthaveacontactseparationofatleast3mminallpoles.The
circuit should be protected by a suitably rated RCD.
HS140/HS040(40ltr)shouldbeprovidedwiththeirowndedicated30Asupply.
TheelectricalinstallationshouldcomplywithcurrentIEEregulationsandany
LocalAuthorityrequirements.
c. Apotablecoldwatersupplywithaminimumworkingpressureof0.07MPa
(0.7bar)andamaximumworkingpressureof0.7MPa(7bar)connectedviaan
isolation valve.
d. Outletdrainagetoasinkdrainingboardortoadriptray.
e. Accesstodrainagefromaventsituatedatthebaseoftheheater.
f. Inallinstallationinstancesthewallsoftheheatermustbeverticalandthebase
horizontal,therecanbenoexceptionstothisrule.
g. Note: Ifthewaterpressureislikelytoexceed7bar,a3.5barpressure
reducingvalvemustbeinstalledinthecoldwatersupplyline.
Size Kw Amps
10 Ltr 3.0kW 13 A
15 Ltr 3.0kW 13 A
25 Ltr 3.0kW 13 A
40 Ltr 6.0kW 30 A
Installation Requirements Cont.
Concealed
Services
Exposed
Services
MinimumClearanceinmm

Page 7 of 12 Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03
Installation Procedures Continued
Approximate Weights When Filled
10Litremodels 29.5kg
15Litremodels 34.5kg
25Litremodels 47.0kg
40Litremodels 71.0kg
250mm
Wiring
Concealed
Vent
Concealed
Inlet
45mm
Fig. b
Fig. a
VisibleTundishVentline
Surfacemount
cable entry
TerminalBlock
Concealed
cable entry
Step 3 – Connecting
a) Plumbing
Forexposedplumbingconnection,connectthecoldwaterinletpipefromthebase
oftheheaterdirectlytothe15mmorinchBSPcompressionfittings.
Forconcealedplumbingconnections,connectthecoldwaterpipethroughtherear
ofthechassisusinga15mmorinchBSPcapillaryelbow.
Coldwaterpipesmustbeflushedbeforeconnectiontotheinlet.Anycloggingdue
tosedimentorfineswilladverselyaffecttheoperationoftheheater.
Itisrecommendedthattheheaterbeinstalledwithaisolatingvalvewhichallows
ittobeisolatedfromthemainssupplyforservicing.
Water pressure requirements:
Minimum-0.07MPa(0.7bar)Maximum-0.7MPa(7bar).
Caution:Ifpressureislikelytoexceed0.7MPa(7bar),apressurelimitingvalvemust
beinstalledinthecoldwatersupplyline.Ziprecommendsavalveratedat3.5bar
(0.35MPa)forthisapplication(ZippartNo.AQ3).
b) Venting
Aventatthebaseoftheheatermustbeplumbedtoasafevisiblelocationas,
undercertainconditions,itmaydischargecoldorboilingwaterand/orsteam.
Forexposedventplumbing,connectventoutletfromthebaseofheatertoa
15mmorhalfinchODpipewhichhasacontinuousfall,isnomorethan3metres
long,hasnomorethan3rightanglebends,anddischargestoawastewater
drain.
Forconcealedventplumbing(Fig.a),connectplumbingtotheventoutletfromthe
heaterrearusingacapillaryelbowprotruding45mmfromthewall.Theplumbing
mustthenbedirectedtoatundishthatmustbeinavisiblelocationbeforebeing
plumbedawaytowaste.
Alternativelyattachthetundishtothewall(Fig.b)andplumbawaytowaste.
c) Electrical
Forconcealedelectricalconnection,connectapowercablefromtherearofthe
heatertotheterminalblockwithintheheaterasshown.
Forsurfacemountinstallationrunthepowercablethroughthecableentryglandat
thebottomoftheunittotheterminalblockwithintheheater.Ensurethecableis
firmlysecured.
Isolationswitchesmusthaveacontactseparationofatleast3mminallpoles.
Do not turn the power ONuntilwaterflowsfromthetap.

Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03 Page 8 of 12
Tap Operation
ZipHydroboilisfittedwithatwo-waytapforinstantboilingwater.
Care should be taken not to touch the metal body of the tap which can
become very hot.
Forinstantboilingwater,gentlypullthetapleverforward.Boilingwaterwill
flowuntilthetaphandleisreleased.
Thisoperationgivesfingertipflowcontrolforsafefillingofcupsandmugs.
To fill larger vessels such as teapots and saucepans, rotate the lever 180
degreesanddepressituntilitlocksintoahorizontalposition.
Boilingwaterwillflowuntiltheleverisreturnedtoitsnormalvertical
position.Thisoperationallowsthevesseltobefilledwithoutholdingyour
handwhereitmaybeaffectedbysteam.
Inlet water
temperature 15°C 10°C
10Litremodels 38minutes 40minutes
15Litremodels 40minutes 43minutes
25Litremodels 47minutes 50minutes
40Litremodels 60minutes 64minutes
Operating Procedures
Step 4 - Assembling
Placetheheatercasebackontothechassisandsecurethetwotopand
fourbottomfixingscrews.
Caution! To ensure correct fitment of the tap assembly, follow the
instruction a to c below carefully.
Removetheblackplasticcapfromthehotoutlettube.PTFEtapehasbeen
pre-appliedtothehotoutlettube(checkitisingoodconditionbefore
proceeding).
IfnotremovethedamagedPTFEtapeandcarefullyapplytwotothree
completeturnsofnewPTFEtapeontothethreadsinaclockwisedirection
asshownalongside.
a. Screwthetapassemblyclockwiseontothetapoutlettube.
b. Continueturningclockwiseuntilthetapassemblyjusttouchesthe
fasciawithoutpressure.
c. Continuetoturnthetapuptoonefullturnmaximumuntilthetap
leverisintheuprightposition.(Donotforcethetapupright;ifyou
cannotgetthetaptotheuprightpositionwithoutapplyingundueforce,
removethetap,startthethreadinanewpositionorapplyafewmore
turns of PTFE and repeat the procedure.
Step 5 - Commissioning
Checkprevioussteps.TurnwatersupplyON.Waterisnowflowinginto
theheater,checkallconnectionsforleaks.Waitapproximately5minutes
andcheckoutlettapforwater.Thisisachievedbypullingthetaphandle
forward.
Do Not turnonthepoweratthisstage.
Ensurethetaphandleiscorrectlyadjustedtoitsoptimumposition.
• Screwtheredknurledcapclockwiseuntilhandtightwithoutusing
excessiveforceoratoolofanykind.
• Slowlyunscrewtheknurledcapanti-clockwiseuntilthetapstartsto
drip.
• Tightentheknurledcapahalfaturnclockwise.Thedrippingwillstop
andthetapwillbesetattheoptimumposition.
Whenthetaphasbeenadjustedandtheunitisfullofwaterturnthepoweron.
Afterashortperiod,boilingwaterwillbeavailableandwillbemaintained
closetoboilingpointthereafter.Initialheatingperiodsareshowninthetableon
the left.
Installation Procedures Continued
o-ring
Note: If the heater is used for filling cups,
theninserttheflowrestrictorintotheoutlet
pipebeforesecuringtapassemblyasabove.
FlowRestrictor

Page 9 of 12 Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03
Earthing Continuity Verification & Electrical Diagram
Template Dimensions
If required, an earth continuity test
canbeperformedbytestingbetween
the earth pin on the products lead and
aexposedpieceofmetalonthecase
and the tap body.
39.5mm
39.5mm
41mm
41mm
41mm
145mm
42mm
20mm
28mm
54mm
150
Ceiling Clearance
65mm
Wall Clearance
591mm10L
591mm15L
771mm25L
831mm40L
374mm(10L,15L,25L)499mm(40L)
295mm(15L,25L)420mm(40L)
188mm(10L,15L,25L)
313mm(40L)
200mm
CONCEALEDVENTPOSITION
COLD INLET POSITION
Warning:Thisappliancemustbeearthed.
Following remedial service the earthing continuity of the heater must be checked by a
qualified technician using an appliance tester, or continuity tester of accuracy Class 5 or
better. Class 5 denotes an accuracy of 5% full scale deflection.
1. Isolatepowersupply.
2. Setmeterto0ohmwithleadsconnectedtogether.
3. Connect one test lead to the earth pin on the three pin plug.
4. Connecttheothertestleadtoabarepatchofmetal(preferablyontheedge)ofthetopofthe
cover, then to the front cover of the unit, and then to the tap top under the plastic paddle.
Thiscanbeachievedbyinsertingtheprobeupfrombehindthepaddlewithoutlosingwater.
Warning:Thewatermaybeboiling-showextracare.
5. Testthatineveryinstancetheelectricalresistancedoesnotexceed1ohm.

Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03 Page 10 of 12
Problem Solving
Symptom Possible Cause Solution
Failstodispensewater.
Water isolating valve turned off. Checkwatersupplyvalve.
Blockedfilter,metertube,strainer,jammedball
valveassemblyorairlockintransfertube. Contact a Zip authorised agent.
Water not boiling. Nopower. Checkpowersupply.
Faultythermostat,element,cutoutorcontactor. Contact a Zip authorised agent.
Runsoutofboilingwaterand
fails to refill.
Internaladjustment. Contact a Zip authorised agent.
Outlet tap drips.
Overflowfromvent.
Excessivesteamfromvent.
Power“on”butnoheat.
Overload repeatedly tripping
withexcessivesteam.
Overload repeatedly tripping
withoutexcessivesteam.
Maintenance / Cleaning
Formaintenanceandsixmonthlysafetychecks,pleaserefertothePreventativeMaintenancesheetNo.85695included
withtheHydroboil.
MaintenanceshouldbecarriedoutbyaZipauthorisedtechnician.
Cleaning Case: Do not use strong, corrosive, spray or abrasive cleaners.
Cleanthecasewithasoftclothorbrushandmildsoapandwater.
SingleElementUpTo3KwwithOnePole
T.O.LThermalOverLoad
ThermostatControlled
HS140 & HS040 With Contactor
T.O.L:ThermalOverLoad
ThermostatControlled

Page 11 of 12 Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03
Spare Parts
Key Part No Description
1 SP6245 Cisternlidclampkit
2 SP90120 Cisternlidgasketkit
3 SP90490 Gasketkit
4 SP90083 Floatvalvekit,withfloat
5 SP90069 Jumpervalvekit,withseals
6 SP90102 Cistern float
7 SP90494 Transfertubekit-2.4kW
7 SP90531 Transfertubekit–3kW
8 SP90495 Banjoscrew
9 SP90496 O-ringkitcomplete
10 SP90517 Fascia&lenskit
11 SP90110 Fascialightkit
12 SP3947A Thermostatkit1.5-25litres
12 SP3947A Thermostatkit40litre
13 SP1614T Overloadkit
14 SP90501 Taptopkit
Key Part No Description
15 SP90502 Tapassemblycomplete
17 SP90505 Tapnutkit
18 SP90506 Tapextension
19 SP90486 Elementkit3.0kW230V
20 SP90491 Cleaningholecoverkit
21 SP90492 Draincap&sealkit
 SP90522 Cisternjetnozzlekit
SP90130 Lid clips
 SP81230 Tapflowrestrictor
 SP88318 Cisterntank
 SP88490 Cisterntankgrommetkit
SP6590 Contactor 40 litres
 SP88343 Maintank10L
 SP88344 Maintank15L
 SP88345 Maintank25L
 SP88346 Maintank40L

Page 12 Zip Hydroboil - Installation & Operating Instructions - 81447 - April 2013 v1.03
Head Office
ZipHeaters(UK)Ltd
14 Bertie Ward Way
Dereham
NorfolkNR191TE
Website:www.zipheaters.co.uk
 [email protected]
Telephone: [phone]
Facsimile:01362692448.
Warranty Information
CertainwarrantiesmaybeimpliedbylawintoyourcontractwithZip.The
warrantyprovidedbelowisadditionaltotheseimpliedwarrantiesandnothing
setoutbelowshalllimityourstatutoryrightsorrightsatlaw.
ZipHeaters(UK)Ltdwarrantsthat,shouldanypartfailwithin24calendar
monthsofinstallation,thatpartwillberepairedorreplacedfreeofchargeby
ZiporitsDistributororServiceProvider,exceptassetoutbelow,provided
theapplianceisinstalledandusedstrictlyinaccordancewiththeinstructions
supplied,andthatfailureisnotduetoaccident,misuse,abuse,unsuitable
waterconditions,ortoanyalteration,modificationorrepairbyanypartynot
expresslynominatedbyZip.
Nocostsarepayablebythecustomerotherthananymileageortravelling-time
chargesincurredbyaZipServiceProviderorthecostofremoval,cartageand
re-installationofanycomponentoftheapplianceifitneedstobereturnedfor
repair to Zip or its Distributor.
Thiswarrantydoesnotcoverdamageresultingfromnon-operationofthe
appliance,theuseofnonauthorisedpartsorconsequentialdamagetoany
other goods, furnishings or property.
Nowarrantyappliestothelifeofanyfiltrationcartridgeinstalledwiththe
applianceascartridgelifemayvaryaccordingtowaterqualityandtherateof
waterconsumption.
Zipdoesnotexclude,restrictormodifyanyliabilitythatcannotbeexcluded,
restrictedormodifiedorwhichcannot,excepttoalimitedextent,beexcluded,
restrictedormodifiedasbetweentheowneroruserandZipunderthelaws
applicable.
Furthermore,thiswarrantydoesnotdisplaceanystatutorywarranty,but,tothe
extenttowhichZipisentitledtodoso,theliabilityofZipunderanystatutory
warrantywillbelimitedatZip’soptiontothereplacementoftheappliance
orsupplyofequivalentappliance,thepaymentofthecostofreplacingthe
applianceoracquiringanequivalentappliance,orthepaymentofthecostof
having the appliance repaired or the repair of the appliance.
Registering Your Purchase
RegisteringyourZipinstallationontheZipwebsitemayhelptoestablishdate
ofinstallationshoulditbecomenecessarytoservicetheapplianceunderterms
oftheZipwarranty.Toregisteryourinstallationgotowww.zipheaters.co.uk
andlookundertheheading“Warranty”.
End of life disposal
Theuseofthiscrossedoutwheeledbinlogoindicatesthatthisproductneedstobedisposedof
separatelytoanyotherhouseholdwaste.
WithineachoftheEuropeanUnionmembercountries,provisionshavebeenmadeforthecollection
andrecyclingofunwantedelectricalandelectronicequipment.
Inordertopreserveourenvironmentweaskthatyoudisposeofthisproductcorrectly.
PleasecontactZipCustomerServiceforadviceon08456005005.