Zip Hydroboil Plu series Parts list manual

Installation Instructions and Operating Procedures
Zip Hydroboil Plus
Filtered instant boiling water plus filtered ambient drinking water
Zip Hydroboil Plus 3 Litre with Sub Micron Triple Action Filter
Zip Hydroboil Plus 5 Litre with Sub Micron Triple Action Filter
Zip Hydroboil Plus 7.5 Litre with Sub Micron Triple Action Filter
Zip Hydroboil Plus 3 Litre with Five Micron Triple Action Filter
Zip Hydroboil Plus 5 Litre with Five Micron Triple Action Filter
Zip Hydroboil Plus 7.5 Litre with Five Micron Triple Action Filter
Zip Five Star Sub Micron Triple Action Replacement Filter
Zip Five Star Five Micron Triple Action Replacement Filter
®

Page 2 of 16 Zip Hydroboil Plus- Installation & Operating Instructions - 82869 - May 2003
Read These Warnings First . . . . . . . . . . . . . .3
Installation Requirements . . . . . . . . . . . . . . .3
Installation Procedures . . . . . . . . . . . . . . . . .4
Step 1 – Positioning . . . . . . . .4
Step 2 – Fastening . . . . . . . . .4
Step 3 – Connecting . . . . . . .4
a) Plumbing . . . . . . . .4
b) Filtration . . . . . . . .5
c) Venting . . . . . . . . .5c) Venting 6
d) Electrical . . . . . . . .6
Step 4 - Assembling . . . . . . .6
Wall mounting Template
and Electrical Diagrams . . . . . . . . . . . . . . . . .6
Installation Procedures Continued . . . . . . . . .7
Srep 5 - Commissioning . . . .7
Problem Solving . . . . . . . . . . . . . . . . . . . . . .7
Earthing Continuity Verification . . . . . . . . . . .8
Operating Procedures . . . . . . . . . . . . . . . . . .8
How to Replace the Filter . . . . . . . . . . . . . . .10
Main PCB Settings . . . . . . . . . . . . . . . . . . . . .11
Connecting John Guest Fittings . . . . . . . . . . .11
Filter Performance Data - Part 28005 . . . . . .12
Filter Performance Data - Part 28002 . . . . . .13
Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . .14
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Contents

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 3 of 16
Read These Warnings First
Please read all installation requirements, installation procedures and
precautions before installing any Zip Hydroboil Plus instant boiling water heater.
Never attempt to install any Zip Hydroboil Plus instant boiling water heater
without reading all of the applicable instructions.
In some hard water areas where mineral scale accumulation in the boiling
chamber of the Zip Hydroboil Plus may become a problem, consideration
should be given to the maintenance required. A suitable form of water
treatment may be necessary.
In areas where the water supply is known to have high sediment levels,
installation of a Zip Hydroboil Plus model equipped with sub-micron filtration is
not recommended. A model equipped with five micron filtration should perform
more satisfactorily.
All plumbing connections must be made in accordance with UK Water
Authorities.
The Zip Hydroboil Plus instant boiling water heater is not intended for use by
young children or infirm people without supervision.
Young children should be prevented from having access to ensure that they are
not able to use or play with the heater.
If the installation site is located more than 1000 metres above sea level, the
installer should contact Zip for high altitude settings.
This appliance must be earthed. If the power supply cord is damaged it must
be replaced by a Zip Service Provider or a qualified electrician.
Do not remove the cover of the heater under any circumstances without first
isolating the heater from the power supply.
Do not use strong, corrosive or abrasive cleaners to clean the case of the
heater.
Before installing, ensure that the following are available:
a) Sufficient space to position the heater so there is at least 150 mm
clearance above the heater for service access,65 mm to its left and
20 mm to its right – the tap outlet usually should be positioned at least
200 mm above a draining board or drip tray.
b) Standard 13 amp fused spur power outlet positioned as shown on the
paper mounting template for connection from the rear of the heater to the
terminal block within the heater, OR a standard 13 amp double pole fused
spur power outlet on the wall within 1500 mm of the heater.
c) Cold water supply with a minimum working pressure of 1 bar (100 kPa)
and a maximum working pressure of 7 bar (700 kPa) connected via an
isolation valve.
d) Outlet drainage to a sink draining board or to a drip tray.
e) Access to drainage from a vent situated at the base of the heater.
If the water pressure is likely to exceed 7 bar (700 kPa), a 3.5 bar
(350 kPa) pressure reducing valve must be installed in the cold water
supply line.
Installation Requirements

Page 4 of 16 Zip Hydroboil Plus- Installation & Operating Instructions - 82869 - May 2003
Before You Begin
Locate the paper mounting-hole template packed with the heater.
Read the installation and operating instructions completely.
Decide whether to install with concealed or exposed plumbing and/or electrical
connections. Concealed connections are preferred for superior appearance.
Step 1 – Positioning
Position the heater so the tap will drain on to a draining board or drip tray.
Position the base of the tap to be not less than 200 mm above the draining
board (height should be increased only if essential for filling larger vessels).
Provide clearance for service access of not less than 150 mm top, 65 mm left,
20 mm right.
Mark corner positions for the heater on the wall so as to position the paper
mounting-hole template.
Step 2 – Fastening
Position mounting-hole template on wall and drill holes where shown.
Drill holes for water inlet, vent outlet and wiring if rear access is intended.
Remove cover fastening screws from heater and lift whole cover off heater.
Detach both nozzles from base of heater by removing fastening screws.
Install plumbing and wiring and prepare pipe ends and wiring ends as shown.
Screw heater chassis to the wall using screws or bolts suited to the wall.
Screws or bolts must be capable of supporting the heater weight when filled.
(see table).
Step 3 – Connecting
a) Plumbing
Connect cold water inlet pipe from base of heater to 15 mm-to-quarter-
inch reducing bush (supplied) and then connect filtration system as instructed
below.
Important precaution:- All cold water inlet pipes must be flushed before
connection to avoid the risk of the heater clogging due to sediment or
metal fines.
3.0 Litre models 12.5 kg (27.5 lbs)
5.0 Litre models 16.5 kg (36.4 lbs)
7.5 Litre models 20.5 kg (45 lbs)
Installation Procedures
COLD
INLET
VENT
OUTLET
INLET
POSITION
VENT
POSITION
250 mm
Wiring
Concealed
Vent
Concealed
Inlet
45 mm
45 mm
Approximate Weight When Filled

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 5 of 16
b) Filtration
Fasten filter head assembly to an under-sink internal cupboard wall
as closely as possible to directly beneath the heater.
The filter should be positioned where it can be accessed readily for cartridge
changing. Allow 300 mm clearance beneath the filter for ease of access.
Fit an isolating valve (not supplied) to the water supply and connect to the
double-non-return valve (supplied).
Trim a length of quarter-inch flexible tube (supplied) to connect the outlet on
the double-non-return valve to the inlet on the filter head assembly. If
necessary fasten the tube to the wall with cleats provided.
Unpack the filter cartridge and write the date where shown on the label.
Avoid handling cartridge top whilst inserting into head.
Align cartridge tabs with the slots on the under-side of the filter head.
Slide cartridge up into head and rotate left to right one quarter turn until it
stops.
Fit the balance of the quarter-inch tube (supplied) to the outlet of the filter. To
purge air from the filter cartridge, run the tube to drain in the sink. Open the
isolating valve, and run water through the filter (into the sink) for 2 minutes or
until water flows freely.
Note: Freshly installed filters may cause water to appear milky. Water should
clear after running a few litres through the filter.
Turn isolating valve OFF and remove quarter-inch tube from the sink drain.
For superior appearance, fix a chrome plated tube between the sink top and
heater underside as a conduit for the flexible tube.
Trim the quarter-inch tube (supplied) to connect from the outlet of the filter
head assembly to the inlet of the 15 mm-to-quarter-inch reducing bush on
heater inlet. Fasten tube to wall using cleats provided.
Purging procedure
To purge air from a new filter cartridge, disconnect the quarter inch tube from
the outlet of the filter head, connect a temporary tube to drain into the sink,
and use the isolating valve to run water through the filter for two minutes or
until the water runs clear. Disconnect temporary tube and reconnect.
c) Venting
A vent at the base of the heater must be plumbed to a safe visible location as,
under certain conditions, it may discharge cold or boiling water and/or steam.
For exposed vent plumbing, connect vent outlet from the base of heater to a
15 mm or half inch OD pipe which has a continuous fall, is no more than 3
metres long, has no more than 3 right angle bends, and discharges to a waste
water drain.
For concealed vent plumbing, connect plumbing to the vent outlet from the
heater rear using a capillary elbow protruding inch 45 mm from the wall.
Alternatively attach a tun dish to the wall as shown and plumb away to waste.
Note: A “Bug screen kit” is providd to safeguard the vent outlet fom crawling insects. It
is “push” fitted over the open end of the vent pipe when the installaion is complete.
Installation Procedures Continued
Filter head assembly mounted on
cupboard wall.
Heater inlet showing
connection with flexible tube.

Page 6 of 16 Zip Hydroboil Plus- Installation & Operating Instructions - 82869 - May 2003
d) Electrical
For concealed electrical connection, connect a power cable through the rear
access opening of the heater to the terminal block within the heater as shown.
For exposed electrical connection, connect a flex to a standard 13 amp double
pole fused spur power outlet on the wall within 1500 mm of the heater.
Do not turn the power ON until the heater is filled with water.
All isolation switches must have a contact seperation of at least 3 mm in all poles.
Step 4 – Assembling
Place the heater case back on to the heater and secure the top 2 case screws.
Place outlet nozzles on nozzle fascias at base of the heater and secure screws.
Secure two bottom case screws.
Installation Procedures continued
274 (1.5 L & 3.O L)
304 (5.0 L & 7.5 L)
38 (1.5 L & 3.0 OL)
53 (5.0 L & 7.5 L)
65 CLEAR
56
POSITIONING PIN
EXTERNAL PLUMBING
ELECTRICAL WIRING
POSITION
INTERNAL PLUMBING
72 15
25
35 42
COLD
INLET VENT
BENCH TOP
318 5.O L
416 3.O L
448 5.O L
561 7.5 L
38 (1.5 L & 3.O L)
53 (5.0 L & 7.5 L)
150
CLEAR
19
20
Wall Mounting Template Dimensions & Electrical Diagram
3 Lt, 5 Lt & 7.5 Lt HB SINGLE ELEMENT
WITH NMS PCB CONTROLLER WIRING DIAGRAM

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 7 of 16
Step 5 – Commissioning
Check previous steps. Turn water supply ON, check connections for leaks.
Push tap paddle inwards until water flows, release to stop flow of water.
Turn power ON. After a short period, boiling water will be available and will be
maintained close to boiling point thereafter. Initial heating periods are:
Inlet water temperature 15°C 10°C
3.0 Litre models 16 minutes 17 minutes
5.0 Litre models 16 minutes 17 minutes
7.5 Litre models 23 minutes 24 minutes
Problem Solving
Installation Procedures continued
Symptom Possible Cause Solution
Fails to dispense water.
Water isolating valve turned off.
Blocked filter, blocked meter tube,
blocked strainer, jammed ball valve
assy, airlock in transfer tube.
Check water supply valve.
Contact Zip Service Provider
1800 638633
Water not boiling.
No power.
Faulty pcb, faulty element, faulty
sensor. Incorrectly located sensor.
Check power supply.
Contact Zip Service Provider
1800 638633
Runs out of boiling water and fails to
refill.
Outlet tap drips.
Overflow from vent.
Excessive steam from vent.
Power “on” but no heat.
“Power on”, “Filter active”, “Boiling
water” light on but no heat.
No heat, no”Power on” light.
Overload repeatedly tripping with
excessive steam.
Overload repeatedly tripping without
excessive steam.
No water from ambient button.
Internal adjustment. Contact Zip Service Provider
1800 638633

Page 8 of 16 Zip Hydroboil Plus- Installation & Operating Instructions - 82869 - May 2003
Warning: this appliance must be earthed.
Following remedial service the earthing continuity of the heater must be
checked by a qualified technician using an appliance tester, or continuity tester
of accuracy Class 5 or better. Class 5 denotes an accuracy of 5% full scale
deflection.
1. Isolate power supply.
2. Set meter to 0 ohm with leads connected together.
3. Connect one test lead to the earth pin on the three pin plug.
4. Connect the other test lead to a bare patch of metal (preferably on the edge)
of the top of the cover, then to the front cover of the unit, and then to the tap
top under the plastic paddle. This can be achieved by inserting the probe up
from behind the paddle without losing water.
Warning- the water may be boiling - show extra care.
5. Test that in every instance the electrical resistance does not exceed 1 ohm.
Tap Operation
Boiling water
Zip Hydroboil Plus is fitted with a two-way cool-touch safety tap for filtered
instant boiling water.
For filtered instant boiling water, gently press the lower end of the tap paddle
inwards.
Boiling water will flow until the tap paddle is released.
This operation gives fingertip flow control for safe filling of cups and mugs.
For filtered instant boiling water to fill larger vessels such as teapots and
saucepans, lift the tap paddle until it locks into a horizontal position.
Boiling water will flow until the paddle is returned to its normal vertical
position. This operation allows the vessel to be filled without holding your hand
where it may be affected by steam.
Drinking water
Zip Hydroboil Plus is also fitted with a chrome plated push button tap for
filtered drinking water.
For filtered drinking water, press the push button inwards. Filtered ambient
temperature water will flow until the button is released.
Filtered water dispensed by the Zip Hydroboil should be stored chilled as the
process of filtration removes chlorine from the water supply.
Earthing Continuity Verification
TESTER
CONNECT BETWEEN THE
EARTH ON THE THREE PIN
PLUG OR EARTH CABLE
AND EXPOSED METAL
PARTS AS PER POINT 4 AT
RIGHT
Operating Procedures

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 9 of 16
Reading Display Screen
Power On
When the text 'Power On' is illuminated this indicates that the power is
connected and turned on and that the heater is operating normally.
Boiling Water
When the text 'Boiling Water' is illuminated this indicates that the contents of
the boiling chamber has been brought to boiling point and is being maintained
(normally within 1°C of boiling point). During the initial heat-up the contents of
the boiling chamber may be below boiling point for a period, and during that
period the text 'Boiling Water' will not be illuminated.
Filter Active
When the text 'Filter Active' is illuminated, the filter is operating within the pre-
set filter life-span. At the end of the pre-set filter life-span period, the 'Filter
Active' illumination is turned off and the text 'Change Filter' is illuminated. The
life-span is factory set at 9 months but may be changed to 6 or 12 months
(see page 10).
Change Filter
At the end of the pre-set filter life-span period, the text 'Change Filter' is
illuminated, together with a free call telephone number to dial for service
assistance if required. For reasons of hygiene filters should be replaced
promptly as scheduled, or earlier if unpleasant taste or odour is detected or if
water flow ceases.
Cleaning Case
Do not use strong, corrosive, spray or abrasive cleaners. Clean the case with a
soft cloth or brush and mild soap and water.
Operating Procedures continued
Filter Active
Boiling
Water
Change
Filter
Display
Screen
Power On
Boiling Water
0870 608 8888

Page 10 of 16 Zip Hydroboil Plus- Installation & Operating Instructions - 82869 - May 2003
The Zip Hydroboil timer is set to remind you every 9 months to replace your
filter. When a filter change is due, the Change Filter light will come on and
remain on until reset.
Depending on local water quality conditions and usage, the filter may require
changing every 6 to 12 months. You may also need to replace the filter if you
notice unpleasant odours or tastes, or if the flow rate of the tap is persistently
slow.
Some water may drip from the filter head (socket) and attached water lines
during replacement. Keep a bucket and towel handy to catch drips and mop up
any spills.
1. Locate service valve in the water supply line and turn off the water supply.
2. Grasp filter cartridge and twist right to left one quarter turn until it stops.
3. Ease cartridge downwards to detach it from the filter head (socket).
4. Do not tilt the cartridge as dirty water may spill from it if tilted.
5. Unpack replacement cartridge and write date where shown on the label.
6. Avoid bacterially contaminating cartridge top whilst inserting into head.
7. Align cartridge tabs with the slots on the under-side of the filter head.
8. Slide cartridge upward into head and rotate left to right until it stops.
9. Open the service valve and check filter head for leaks. Refit if leaking.
10. To purge air from filter follow purging procedure described on page 5.
11. Wipe up any spills and dispose of spent filter cartridge and packaging
thoughtfully.
12. Insert wire probe into reset Access Hole on heater fascia to reset the “Filter
Active” light and start filter reminder system timer.
Note: Freshly installed filters may cause water to appear milky. The water
should clear after running a few litres of water through the filter.
How to Replace the Filter
Filter Head
Filter Cartridge
To remove cartridge,
turn cartridge one
quarter turn right to
left, and draw
downwards.
To replace cartridge
align lugs on filter
cartridge with socket on
filter head. Push
upwards, turn one
quarter turn left to right
until secure
Reset Access Hole

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 11 of 16
Main PCB Settings
Connecting John Guest Fittings
SW1 (Cutoff termperature)
SW2 (Filter change 9 Months)
SW2 (Filter change 6 Months)
SW2 (Filter change 12 Months)
The cut-off temperature and differential switch SW1 and the filter timer switch
SW2 have a factory presetting as follows:
SW1- cut off temperature of 89°C with 10°C differential
SW2 - Filter timer switch is set at 9 months
Set up temperature cut off to 86°C with 10°C differential for higher altitude
installations.

Page 12 of 16 Zip Hydroboil Plus- Installation & Operating Instructions - 82869 - May 2003
The following filter performance data is supplied in compliance with the relevant Australian
Standard.
SUBSTANCE REDUCTION
Zip Five Star Water Filter Model 28005 (Sub Micron Triple Action for Boiling Water)
Tested and certified under AS/NZS 3497 for reduction of chlorine, cysts, odour, taste, particles
and turbidity. The substances listed may not be in your water
Class Treatment Type Function Pass
I Microbiological Status Will stop bacteria increasing, but will not remove them N/A
Bacteriostatic unless II (a) is passed
II Microbiological Treatment Will remove or inactivate bacteria N/A
II (a) Bacteria Removal
II (b) Virus Removal Will remove or inactivate virus N/A
II (c) Protozoa Removal Will remove or inactivate cryptosporidium and giardia. 3
Will not remove or inactivate bacteria and viruses unless
II (a) and II (b) are passed
III Turbidity and Will reduce cloudiness 3
Particulate Reduction
IV Taste and Odour Reduction Will reduce tastes and odours 3
V Chemical Treatment Will decrease chlorine compounds 3
“This appliance may increase the bacterial content of water unless supplementary
treatment is provided”.
Legend: 3= Pass N/A = Not applicable
PERFORMANCE SPECIFICATION
Zip Five Star Water Filter Model 28005 (Sub Micron Triple Action for Boiling Water)
The filter cartridge has been designed to perform to the following specifications
Particulate (Dirt/Rust) Reduction (for 7570 litres approx) Class 1* (*as tested in accordance with ANSI/NSF Std 42)
Chlorine, Taste/Odour Reduction (for 7570 litres approx) Class 1* (*as tested in accordance with ANSI/NSF Std 42)
Giardia & Cryptosporidium Cyst Reduction** >99.9% Removal
Turbidity Reduction** (**as tested in accordance with ANSI/NSF Std 53)
Substance *Guidelines Average Maximum Minimum Average Average
or †USEPA Influent Effluent Percent Effluent Percent
SDWA MCL Concentration Concentration Removal Removal Removal
Cysts 99.5% 99.9% N/A N/A
(3-4 micron reduction
particles)
Turbidity 5 NTU <0.2 NTU
Chlorine - 2 mg/L 0.1 mg/L 95% N/A N/A
mg/L = milligrams per litre (1 mg/L = 1 part per million)
* Australian Drinking Water Guidelines – 1996
† United States Environmental Protection Agency (USEPA) Safe Drinking Water Act
REPLACEMENT FREQUENCY INSTRUCTION
Zip Five Star Water Filter Model 28005 (Sub Micron Triple Action for Boiling Water)
Be sure to change the filter cartridge at least every 7570 litres or at least every 12 months or
whenever you detect a change in taste, odour, or a decrease in flow – 7570 litres is equal to
using approximately 20 litres daily for one year.
Filter Performance Data - Part 28005

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 13 of 16
Filter Performance Data - Part 28002
A Five Micron filter may be filtered as an alternative to a Sub-Micron filter in areas where
water has high sediment levels.
SUBSTANCE REDUCTION
Zip Five Star Water Filter Model 28002 (Five Micron Triple Action for Boiling Water)
Tested and certified under AS/NZS 3497 for reduction of chlorine, odour and taste as shown
below. The substances listed may not be in your water.
Class Treatment Type Function Pass
I Microbiological Status Will stop bacteria increasing, but will not remove them N/A
Bacteriostatic unless II (a) is passed
II Microbiological Treatment Will remove or inactivate bacteria N/A
II (a) Bacteria Removal
II (b) Virus Removal Will remove or inactivate virus N/A
II (c) Protozoa Removal Will remove or inactivate cryptosporidium and giardia. N/A
Will not remove or inactivate bacteria and viruses unless
II (a) and II (b) are passed
III Turbidity and Will reduce cloudiness N/A
Particulate Reduction
IV Taste and Odour Reduction Will reduce tastes and odours 3
V Chemical Treatment Will decrease chlorine compounds 3
“This appliance may increase the bacterial content of water unless supplementary
treatment is provided”.
Legend: 3= Pass N/A = Not applicable
PERFORMANCE SPECIFICATION
Zip Five Star Water Filter Model 28002 (Five Micron Triple Action for Boiling Water)
The filter cartridge has been designed to perform to the following specifications
Chlorine, Taste/Odour Reduction (for 5678 litres approx): Class 1* (as tested in accordance with ANSI/NSF Std 42)
Substance *Guidelines Average Maximum Minimum Average Average
or †USEPA Influent Effluent Percent Effluent Percent
SDWA MCL Concentration Concentration Removal Removal Removal
Chlorine - 2 mg/L 0.5 mg/L >75% N/A N/A
mg/L = milligrams per litre (1 mg/L = 1 part per million)
* Australian Drinking Water Guidelines – 1996
† United States Environmental Protection Agency (USEPA) Safe Drinking Water Act
REPLACEMENT FREQUENCY INSTRUCTION
Zip Five Star Water Filter Model 28002 (Five Micron Triple Action for Boiling Water)
Be sure to change the filter cartridge at least every 5678 litres or at least every 12 months or
whenever you detect a change in taste, odour, or a decrease in flow – 5678 litres is equal to
using approximately 15 litres daily for one year.

Page 14 of 16 Zip Hydroboil Plus- Installation & Operating Instructions - 82869 - May 2003
Spare Parts
Key Part No Description
1 90487 Cistern Lid Clamp kit 2000B
2 90488 Cistern Lid and Gasket kit 2000B
3 90490 Gasket kit Hydroboil 2000b
4 90083 Float valve kit w/ seals
5 90069 Jumper valve kit w/ seals
6 90102 Cistern float kit w/ nut and screw
7 90493 Metering tube kit 1500w 2000B
90494 Metering tube kit 2400w 2000B
8 90495 Banjo screw Hydroboil 2000B
9 90496 O-Ring kit Hydroboil 2000B
10 90574 Fascia lens kit 2000B (coated)
11 90561 PCB Lights kit
12 90594 Main PCB kit for HB’s
13 90127 Overload kit Hydroboil 2000B
14 90560 Tap Handle Kit (Coated)
15 90562 Outlet Nozzle Kit (S/S)
16 90503 Strap and key kit 1.5 & 3L 2000B
90504 Strap and key kit 5 & 7.5L 2000B
17 90505 Tap nut kit Hydroboil 2000B
18 90509 Tap body kit Hydroboil 2000B
19 90485 Element kit 1500W / 240V 2000B
90486 Element kit 2400W / 240V 2000B
20 90491 Clean hole cover kit
21 90492 Drain cap & seal kit
22 90587 Sensor Probe Kit
23 90107 Filter kit Cold Inlet Bush
24 90223 Cartridge Valve Kit
25 90593 John Guest Fittings Kit
26 90592 Conversions Kit Ambient to Chilled Unit

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 15 of 16
Spare Parts
1
2
4
3
57
8
9
16
17
18
19
22
23
25
26
10
21
20
15
14
13
11
12
24
6
25
26

Zip Hydroboil Plus - Installation & Operating Instructions - 82869 - May 2003 Page 16 of 16
Head Office
Zip Heaters (UK) Pty. Ltd.
14/15 Bertie Ward Way
Rash’s Green Dereham
Norfolk NR19 1TE
Telephone: [phone]
Free Call: 01362 692 448
The Zip appliance you have chosen is precision-built from the finest materials
available and should give many years of trouble free service.
Certain warranties may be implied by law into your contract with Zip. The
warranty provided below is additional to these implied warranties and nothing
set out below shall limit your statutory rights or rights at law.
Zip Heaters (UK) Pty Ltd warrants that, should any part fail within 12 calendar
months of installation, that part will be repaired or replaced free of charge by
Zip or its Distributor or Service Provider, except as set out below, provided the
appliance is installed and used strictly in accordance with the instructions
supplied, and that failure is not due to accident, misuse, abuse, unsuitable
water conditions, or to any alteration, modification or repair by any party not
expressly nominated by Zip.
No costs are payable by the customer other than any mileage or travelling-time
charges incurred by a Zip Service Provider or the cost of removal, cartage and
re-installation of any component of the appliance if it needs to be returned for
repair to Zip or its Distributor.
This warranty does not cover damage resulting from non-operation of the
appliance or consequential damage to any other goods, furnishings or property.
No warranty applies to the life of any filtration cartridge installed with the
appliance as cartridge life may vary according to water quality and the rate of
water consumption.
Zip does not exclude, restrict or modify any liability that cannot be excluded,
restricted or modified or which cannot, except to a limited extent, be excluded,
restricted or modified as between the owner or user and Zip under the laws
applicable.
Furthermore, this warranty does not displace any statutory warranty, but, to the
extent to which Zip is entitled to do so, the liability of Zip under any statutory
warranty will be limited at Zip's option to the replacement of the appliance or
supply of equivalent appliance, the payment of the cost of replacing the
appliance or acquiring an equivalent appliance, or the payment of the cost of
having the appliance repaired or the repair of the appliance.
Registering Your Purchase
Registering your Zip installation on the Zip website may help to establish date
of installation should it become necessary to service the appliance under terms
of the Zip warranty. To register your installation go to www.zipheaters.co.uk and
look under the heading "Warranty".
Warranty Information
The standard cup referred to in this publication is 167 ml (6 fl oz).
The terms "Zip" and "Hydroboil" are registered trade marks.
Zip products described in this publication are manufactured under one or more of the following
patents: AU675601, AU637412, AU635979, GB0422305, GB2065848, US4354049, US5103859,
and US5099825. Other patents are in force and patent applications are pending.