Zippity Ashley Vinyl Corner Picket Fence Kit User manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service department at 1 877 234 6196 (Mon. to Fri. 8:00 AM to 4:00 PM EST).
1. Post Caps (3)
2. Top Rail - Long ( 1) - 1 1/2” x 1 1/2“ x 40 1/8”
3. Top Rail - Short ( 1) - 1 1/2” x 1 1/2“ x 37”
4. Bottom Rail - Long ( 1) - 1 1/2” x 1 1/2“ x 40 1/8”
5. Bottom Rail - Short ( 1) - 1 1/2” x 1 1/2“ x 37”
6. Posts - Tall (1) - 7/8“ x 1 1/2” x 36 3/4“
7. Posts - Short (2) - 7/8” x 1 1/2“ x 30”
8. Pickets (16) - 1 - ¼” x 1½” x 26 1/8“
2 - ¼” x 1½” x 24 5/8“
3 - ¼” x 1½” x 23 1/4“
4 - ¼” x 1½” x 22 1/8“
5 - ¼” x 1½” x 21 1/4“
6 - ¼” x 1½” x 20 5/8“
7- ¼” x 1½” x 20 1/8“
8 - ¼” x 1½” x 20”
9. 3/4”Self-Auguring Stainless Steel Screw (12)
10. 2 1/2”Self-Auguring Stainless Steel Screw (2)
Tools You Will Need
• Cordless Drill
• Level
• Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e.shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Ashley Vinyl Corner Picket Fence Kit
(40”W x 30”H)
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Ver 1.0/053015
1
8
2
7
9
Ground
5
10
Not to Scale
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
7 1/4 in
13 1/2 in
4 3/4 in
2 in
30 in
38 1/2 in
40 in
23 1/4 in
3
6
4

2
Position the top and bottom long rails as illustrated and slide
the one short and one tall post down thru the large routed
holes in the rails until the pre-drilled holes in the post and rails
are aligned.
Note the difference between the top and bottom rails.
Tip!
Shine an LED light from smart phone or flashlight down the
end of the posts to help identify alignment of pre-drilled
holes if necessary.
Once all the holes are aligned, screw the top and bottom
rails into both sides of both posts.
1
2
STEP ONE
Ashley Vinyl Corner Picket Fence Instructions
1
Note: Align Holes
2
Note: Orientate the bottom of Posts as Illustrated
Note: Underside of Bottom Rail
is blank compared to the
Top Rail with holes for
pickets on both sides.
Assemble Full Panel
Long Post
Short Post
Two Pre-Drilled Holes

3
STEP TWO
Ashley Vinyl Corner Picket Fence Instructions
Pickets are identified 1, 2, 3, 4, 5, 6, 7 and 8 to create scallop
pattern. Please insert in pattern as identified in illustration.
Starting with the tallest picket, slide each one down thru the
top rail and into the bottom rail.
Note: The tabs on the bottom of the pickets are intended to
go into the bottom rail to lock picket in place.
1
1
2
1345678
2
1
Note: Once inserted, the pickets will lock into place.
To remove the picket(s), gently insert a butter knife
along the picket direction as shown and slowly pull
up the picket(s).

Ashley Vinyl Corner Picket Fence Instructions
4
Position the top and bottom short rails as illustrated and slide
the one short post down thru the large routed holes in the rails
until the pre-drilled holes in the post and rails are aligned.
Note the difference between the top and bottom rails.
Once all the holes are aligned, screw the top and bottom
rails into both sides of the post.
1
2
STEP THREE
1
Note: Underside of Bottom Rail
is blank compared to the
Top Rail with holes for
pickets on both sides.
Note: Align Holes
2
Note: Orientate the bottom of Post as Illustrated
Assemble Partial Panel

5Ashley Vinyl Corner Picket Fence Instructions
STEP FOUR
Pickets are identified 1, 2, 3, 4, 5, 6, 7 and 8 to create scallop
pattern. Please insert in pattern as identified in illustration.
Starting with the tallest picket, slide each one down thru the
top rail and into the bottom rail.
Note: The tabs on the bottom of the pickets are intended to
go into the bottom rail to lock picket in place.
1
1
2
1345678
2
1
Note: Once inserted, the pickets will lock into place.
To remove the picket(s), gently insert a butter knife
along the picket direction as shown and slowly pull
up the picket(s).

Ashley Vinyl Corner Picket Fence Instructions
6
1
2
Fasten the Panels Together
Bring the two panels together as shown (you might need a
helper).
Fasten the two panels together using the long screws
provided through the pre-drilled holes as shown.
1
STEP FIVE
2

7Ashley Vinyl Corner Picket Fence Instructions
Block
of Wood
1
2
Install fence into Ground
Move the fence to its final location and identify the location
of posts.
Attempt to push the unit into the ground as illustrated
Optionally:
1
x
x
x
1. If your ground is too hard, loosen the top 4” of the ground
with a claw hammer as illustrated.
2. Add water to loosen soil
3. Use a block of wood to the protect the top of post and
gently hammer each post into the ground equally.
Push down on the top of posts
with both hands
Option 3:
x
x
x
Option 1:
Option 2:
x
x
x
x
x
x
STEP SIX

8
10616 Bailey Road, Unit H, Cornelius NC 28031
Toll Free Phone: [phone] Fax: [phone]
www.zippity-outdoor.com
STEP SIX
DO-IT-YOURSELF
FRIENDLY PRODUCTS
Zippity
4
3
Level
3
Install fence into Ground - Continued
Level the assembled unit and backfill and compact dirt around
the base of each post to strengthen the unit.
Finish the assembly by pushing the post caps down over the
top of posts as illustrated. The post caps will lock into place.
4