Zircon POP-950-D5 User manual

Zircon Series
All-in-One POS System
User Manual
POP-950-D5
Ver. 1.2
© Copyright Fametech Inc. (TYSSO), 2013

i
General Information
ABOUT THIS MANUAL
The purpose of this user’s manual is to provide general information on TYSSO Zircon Series
(POP-950) POS System and to show the users how to configure the hardware-related
configurations. The information in this manual is subject to change without notice due to rapid
improvement on IT technology.
Users can get the most up to date information from our web sites:
Uhttp://www.fametech.com.twU
DISCLAIMER
This manual has been examined for accuracy. While precaution has been taken in the
preparation of this manual, neither the manufacturer takes no liability for errors or omissions nor
assume any responsibility for damage(s) incurred directly or indirectly from errors, omissions, or
discrepancies of this manual.
IN NO EVENTWILLTHE VENDOR BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY
TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF THE POSSIBILITY OF SUCH
DAMAGES HAS BEEN ADVISED. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FORANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, OR RECOVERING SUCH
HARDWARE, SOFTWARE OR DATA.
WARNING
The terminal has been tested and found to comply with the limits for a Class a digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interface in a residential installation. This equipment can generate and radiate
radio frequency energy and, if not installed and used according to the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interface will
not occur under particular installation. If this equipment does cause harmful interference to radio
or television reception, which is found by turning the equipment off and on, the user is
encouraged to try to correct the interface by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment or device
Connect the equipment to an outlet other than the receiver’s
Consult a dealer or an experienced radio/TV technician for assistance

ii
CAUTION
The system is provided with a battery-powered Real-Time Clock circuit. There is a danger of
exposing and personal injury if the battery is incorrectly replaced or mistreated. Do not attempt to
disassemble the battery, immerse it in the water or expose it to fire.
WARRANTY LIMITS
If the product and the parts are disassembled by any person other than the authorized
technicians, the warranty will be terminated. The users should consult his/her dealer for any
technical problems. Warranty does not cover any damage caused by improper use.
TRADE MARKS AND SERVICE MARKS
TYSSO is a registered trademark of FAMETECH INC.
Other brand and product names are trademarks and registered trademarks and service marks of
their respective owners.

iii
IMPORTANT SAFETY INFORMATION
Read following instructions carefully.
Use only parts, especially power adapter, recommended by the manufacturer; unapproved
parts may be hazardous.
Before plugging the power cord into theAC inlet of the power supply unit, make sure that
the voltage applied to the power outlet is within the specified range (100V ~240V).
Improper power source voltage range will cause damage to the power supply unit.
Power off the system and remove the power adapter while cleaning the system.
Before powering on the system, make sure all the peripherals are firmly installed.
Do not use the system near water, such as a bathtub, a washbowl, a kitchen sink, a laundry
tub, and a swimming pool. Do not expose the machine under direct sunlight, and keep it
away from any heat source.
Do not place the system on an unstable cart, stand or table. If the machine falls, it may injure
a person or cause serious damage to the appliance.
The system is equipped with athree-wire grounded plug with a third (grounding) pin. This is a
safety feature. If your outlet does not accommodate the three-wire plug, have an electrician
install a correct outlet, or use an adapter to ground the appliance safely. Do not leave out the
safety purpose of the grounded plug.
Do not allow anything to rest on the power cord. Do not locate the system where people may
walk on the cord.
Do not make the power outlet and extension cords overload. Overload can result in fire or
electric shock.
Do not push any object into the computer cabinet. Dangerous voltage points may be touched
and the parts may be shorted out resulting in fire or electric shock.
Do not attempt to service the system on your own. Opening or removing cover can expose
you to dangerous voltage or other hazards.
Power off the system before installing or removing non-PNP (plug and play) devices.
If any of the following situations occurs, unplug the systems from the power outlet
immediately and consult with a qualified service person:
1. The power cord or plug is damaged or frayed.
2. Liquid is spilled into the system.
3. The system is dropped or the cabinet is damaged.
When the system is not in use, cover the system and store it with care.

Contents
General Information.............................................................................................................i
ABOUT THIS MANUAL......................................................................................................i
DISCLAIMER.....................................................................................................................i
WARNING .........................................................................................................................i
CAUTION ......................................................................................................................... ii
WARRANTY LIMITS .........................................................................................................ii
TRADE MARKS AND SERVICE MARKS ..........................................................................ii
IMPORTANT SAFETY INFORMATION............................................................................. iii
1. Product Overview.........................................................................................................1
1.1. Items........................................................................................................................1
1.2. Specifications...........................................................................................................2
1.3. Parts Description......................................................................................................6
1.4. I/O Ports ..................................................................................................................8
2. Components & Peripherals Installation..................................................................10
2.1. Unpack Your POS ..................................................................................................10
2.2. Install Your POS System ........................................................................................11
2.3. Replace the Hard Disk............................................................................................12
2.4. Plug AC Power Cord to the POS System................................................................13
2.5. I/O Interface...........................................................................................................14
2.6. Install Your Receipt Printer (Optional) .....................................................................15
2.6.1. Install/Replace the Paper Roll....................................................................................15
2.6.2. Buttons & Indicators of Receipt Printer Unit...............................................................16
2.6.3. Dip Switch Configuration of the Receipt Printer .........................................................17
2.6.4. Virtual Serial Port Installation (for USB Connection Only)..........................................19
2.6.5. Install the Driver and Setup of Receipt Printer Unit....................................................24
2.7. Adjust the Customer Display (Optional) ..................................................................30
2.8. Configuration of Customer Display..........................................................................30
3. BIOS Setup ..................................................................................................................31
3.1. Main Menu.............................................................................................................32
3.2. Standard CMOS Features ......................................................................................33
3.3. Advanced BIOS Features.......................................................................................34
3.4. Advanced Chipset Features....................................................................................36
3.5. Integrated Peripherals............................................................................................38
3.5.1. OnChip IDE Device ...................................................................................................39
3.5.2. Onboard Device ........................................................................................................41
3.5.3. Super IO Device........................................................................................................42
3.5.4. Second IO Device......................................................................................................43
3.5.5. USB Device Setting...................................................................................................44

v
3.6. Power Management Setup .....................................................................................45
3.7. PnP/PCI Configurations..........................................................................................47
3.8. PC Health Status....................................................................................................48
3.9. Frequency/Voltage Control .....................................................................................49
3.10. Load Fail-Safe Defaults..........................................................................................50
3.11. Load Optimized Defaults ........................................................................................51
3.12. Set Supervisor Password .......................................................................................52
3.13. Set User Password ................................................................................................53
3.14. Save & Exit Setup ..................................................................................................54
3.15. Exit Without Saving................................................................................................55
4. Install the Drivers of POS Terminal .........................................................................56
4.1. Install the Chipset Driver.........................................................................................57
4.2. Install the Graphics Driver ......................................................................................59
4.3. Install theAudio Driver............................................................................................63
4.4. Install the LAN Driver .............................................................................................65
5. Install the Touch Screen Driver................................................................................67
5.1. Install the Driver of Resistive Type Touch Panel ......................................................68
5.2. Touch Screen Calibration (Resistive Type)..............................................................72
6. Peripherals Testing ....................................................................................................75
6.1. Install the Wi-Fi Driver (Optional)............................................................................76
6.2. Test Your Magnetic Stripe Card Reader(MSR) and i-Button Module.........................80
6.3. Test Your Customer Display....................................................................................86
6.4. Cash Drawer..........................................................................................................88
7. Jumper Settings & Connectors................................................................................91
7.1. The Main Board Jumper Location...........................................................................91
7.2. Jumper Settings.....................................................................................................92
7.3. Connector Function List..........................................................................................95
7.4. Internal Connector Pin Assignment.........................................................................96

1
1. Product Overview
1.1. Items
Main System
HDD (2.5” SATA) / Compact Flash (Optional) / Disk on Module (Optional)
SODIMM DDR3 (1 ~ 4GB)
CPU: Intel Atom D525 Dual Core (1.8GHz , 1MB Cache)
Power Adapter (Hidden under Base)
AC Power Cord
Driver/Utility CD
Optional Accessories
Magnetic Stripe Card Reader (MSR)
Customer Display
Wi-Fi module
Thermal Receipt Unit
I-Button
Secondary Display
* For more information relating to the other optional peripherals, please contact the local representatives or
technical support personnel of the providers.
POS System
AC Power Cord
Driver/Utility CD

2
1.2. Specifications
Model
POP-950-D5
Main Board
CPU
Intel Atom D525 Dual Core (1.8GHz, 1MB Cache)
Chipset
Intel D525 + ICH8M
System Memory
2 x 204pin DDR3 SODIMM Socket , up to 4GB
Graphic Memory
Share System Memory 64~224MB
OS Support
Linux, POS Ready 2009, POS Ready 7,
Windows XP Pro, Vista, Windows 7
Display
Display Type
15" LCD Monitor
Brightness
250 nits
Resolution
1024 x 768 Pixel
Touch Screen
Flat 5 Wire Resistive Type
Tilting Angle
Fixed 50 Degree
Storage
HDD
1x 2.5" SATA
Compact Flash
1 x Slot Type I II
Interface
Serial
2 x COM with Power Selected 5/12V
1 x COM without Power Output
Parallel
1 x DB25 Parallel Port
USB
6 x USB 2.0 (External)
2 x USB 2.0 (Internal, 1 reserved for touch screen)
Mini-PCIe
1 x Internal
PS/2 Mouse
1 x 6-pin Mini DIN
PS/2 Key Board
1 x 6-pin Mini DIN
LAN
1 x RJ-45, Giga LAN Support
VGA
1 x DB-15, Female
DC Out
1 x 12VDC Jack for Customer Display or 2nd Display
Cash Drawer
1 x RJ-11, 12/24 VDC Selectable
Audio Jack
1 x Line Out, 1 x MIC In, 2 x Internal Speaker 2W
Others
Power Input (Main Unit)
12VDC 90W,4-pin Connector with Lock
(External Adaptor: 100~240 VAC, 50/60HZ)
Power Input (Printer Unit)
24VDC/2.5A
(External Adapter 100~240VAC 50/60Hz)
Color
White, Black, Orange
Compliance
FCC / CE / WEEE / RoHS
Weight
8.5 Kg
Dimension (W x D x H:mm)
370 x 320 x 300
Operating Temperature
0°C~40°C
Operating Humidity
20% ~ 80% RH non-condensing
Storage Temperature
-20°C~ 60°C
Storage Humidity
20% ~ 85% RH non-condensing

3
Printer Unit (Optional)
General
Print Method
Thermal line printing
Print Speed
250mm/sec
Print Life
100 Km
Print Font
ANK Font
Font A: 12 x 24 dots
Font B: 9 x 17 dots
Chinese character: 24 x 24 dots
Print Resolution
576 dots/line or 512 dots/line
Print Font Character Support
International Font, Big 5 Chinese, GB Chinese,
Japanese, Korean selectable
Character Per Line
48 (Font A) / 64(Font B)
Effective Print Width
72mm
Paper Width
79.5mm± 0.5mm
Paper Roll Diameter
83mm
Paper Thickness
0.06~0.08mm
Print Command
ESC/POS commands set compatible
Auto Cutter
Partial
Paper End Detection
Yes
Over-Heat Halt-on Protection
Yes
Interface (Printer)
Serial
Multi I/O Interface
(Serial +Ethernet +USB)
USB
Ethernet
Cash Drawer
DC 24V/1A, 6-Wire RJ-11 Socket
Others
Power Input (Printer)
24VDC/2.5A
(with External Adapter 100~240VAC 50/60Hz)
Operating Temperature
0°C~45°C
Operating Humidity
10% ~ 80% RH non-condensing
Storage Temperature
-10°C~ 60°C
Storage Humidity
10% ~ 90% RH non-condensing

4
Customer Display Unit (Optional)
General
Display Type
Vacuum Fluorescent Display
Brightness
700 cd/m2
Number of Columns
20 x 2
Character Size (mm)
6.4 x 9.2 (W x H), 5x7 dot matrix
Command Set
ESC/POS
Font Character Support
96 Alphanumeric & 13 international
Interface
RS-232.
Others
Power Input
DC +9V~12V(RS-232)
Power Consumption
4.5 W (RS-232)
Material
ABS
Compliance
CE, FCC
Display Unit
218 x 87 x 45 mm
Support Pole
Telescopic Pole (280~459 mm adjustable)
Base
140 x 18 x 86 mm
Horizontal Rotation
±180 degree
Tilting Angle
53 degree, 4 step adjustable
Operating Temperature
0°C~40°C
Storage Temperature
-10°C~ 50°C
Relative Humidity
0% - 90% RH, non-condensing
Optional Peripherals
MSR
3 Track, PS/2 or USB or COM
i-Button
Dallas Key RS232 I/F
2nd Display
8.4”, 10.4”, 12.1”, 15” with or without Touch
Wi-Fi
Mini-PCIe interface Module
* For more information relating to the other optional peripherals, please contact the local representatives or
technical support personnel of the providers.