ZKTeco DM10 User manual

1
Quick Start Guide
DM10
Version: 1.1
Due to regular upgrades of systems and products, ZKTeco could not guarantee
exact consistency betweenthe actual product and the written information in this manual.

2
1
6
2
7
3
8
4
9
5
10
Appearance & Installation
1.Appearance
Status of indicator
Normal communication: The indicator
flashes every two seconds.
Abnormal communication: The indicator
will glow constantly.
The indicator flashes rapidly within 30s
after the device is connected to the power
supply.
Address SwitchSettingAddressSwitchSetting
Indicator LED
1 2 34
1 2 34
1 2 34
1 2 34
1 2 34
1 2 34
1 2 34
1 2 34
1 2 34
1 2 34
DIPswitch Power
EXTRS485
Auxiliary input
Wiegand reader
Lock
Auxiliary
output 12V output
Wiegand reader
PWR
NO COM NC
485A 485B GND BEEP GLED WD1 WD0 GND 12V BEEP GLED WD1 WD0 GND 12V
GND AUX
BUT GND SEN NO COM NC
12VOUT
GND 12V GND
RS485 ADD.
RS485 AUX IN READER 1 READER 2
AUX OUT LOCK VOUT POWER

3
2.Installation
1)Drill holes on the wall 2)Fix the device with four screws
The DM10 has to be connected to F18(Master Device) to use the software.
An Access Controller can connect to a maximum of
eight DM10.
Each device requires a separate power supply.
GND
485+
485-
EXT
1
DC12V
-
+
-
+
DC12V
Router
Master DeviceConnection
2 8
GND
485A
485B
-
+
DC12V
PWR
NO COM NC
485A 485B GND BEEP GLED WD1 WD0 GND 12V BEEP GLED WD1 WD0 GND 12V
GND AUX
BUT GND SEN NO COM NC
12VOUT
GND 12V GND
RS485 ADD.
RS485 AUX IN READER 1 READER 2
AUX OUT LOCK VOUT POWER
PWR
NO COM NC
485A 485B GND BEEP GLED WD1 WD0 GND 12V BEEP GLED WD1 WD0 GND 12V
GND AUX
BUT GND SEN NO COM NC
12VOUT
GND 12V GND
RS485 ADD.
RS485 AUX IN READER 1 READER 2
AUX OUT LOCK VOUT POWER
PWR
NO COM NC
485A 485B GND BEEP GLED WD1 WD0 GND 12V BEEP GLED WD1 WD0 GND 12V
GND AUX
BUT GND SEN NO COM NC
12VOUT
GND 12V GND
RS485 ADD.
RS485 AUX IN READER 1 READER 2
AUX OUT LOCK VOUT POWER
PWR
NO COM NC
485A 485B GND BEEP GLED WD1 WD0 GND 12V BEEP GLED WD1 WD0 GND 12V
GND AUX
BUT GND SEN NO COM NC
12VOUT
GND 12V GND
RS485 ADD.
RS485 AUX IN READER 1 READER 2
AUX OUT LOCK VOUT POWER

4
Open the ZKAccess3.5 software, click [Device]> [New], enter the name
and IP address of F18 , andthenclick [OK].
Step 1
After proper wiring, please follow the below instructions.
1. Set the RS485 address of DM10 as 2-9.
2. Set the F18 serial port as ”host” ([COMM.]> [serial port]).
Quick Start
Click [More...] > [Add IO Expansion Board] , check the RS485 address of
DM10, andthenclick [OK].
Step 2

5
After successful configuration, the flashes every two 2 Indicator LED
seconds, indicating that the communication is normal. After adding
successfully, the parameters of the access control unit could be set, please
refer to the ZKAccess 3.5 user manual for further details.

6
ZKTeco Industrial Park, No. 26, 188 Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
Copyright © 2020 ZKTECO CO., LTD. All Rights Reserved.