ZKTeco Green Label ProlD104 User manual

QUICK START GUIDE
Applicable Model: ProlD104
Version: 1.0
Date: June 2023
Scratch Proof RFID Access Control Reader

1.Caution
1
•Electricity is strictly prohibited during installation and wiring. Please note: Any
energized connection may cause accidental damage to the equipment, and we
will not provide a normal warranty for damage caused by such operation.
•In a place with severe static electricity or in winter, connect the ground
cable before other cables to prevent transient static electricity from
damaging the device, and then connect the power cable. If the device
cannot run properly, turn off the main power switch immediately and
perform necessary checks.
•12V/1A power supply is recommended. For details, contact technical personnel.
•The exposed part of the wiring terminal must be less than 5mm to prevent
accidental contact with the long bare cables and damage to the device.
2.Product List
Please confirm that the package contains the following items:
Reader*1 Back Plate
QUIC K START GUID E
Applicable Model: ProlD 104
Version: 1.0
Date: June 2023
Water Resistant RFID Access Control Reader
Screws and Plugs
Quick Start Guide
Qualified Certificate
Cable

2
3.Product Overview
60mm
LED Indicator
Touch Key
ResetButton
Buzzer
Back Plate
86mm
86mm
11.2mm
60mm
Terminal Block
Mounting Hole

3
4. Device Installation
Mounting on the Wall through Asian Gang Box
Install the box (or mullion mountAsian gang single gang box, ) into the wall.
Fix the back plate onto the Asian gang box (or single gang box, ) mullion mount
using two wall mounting screws.
Pass the cables through the wire hole.
Then insert the device into back plate.
Use security screw to fasten the device to the back plate.
①
②
③
④
⑤
5
1
2
Asian Gang Box
3
4
*Only Asian gang box installation is illustrated here.

4
5. Terminal Block
LED
Indicator
Buzzer
Power
Wiegand
Out
RS485
12V
GND
WD0
WD1
GLED
/
BEEPER
/
/
/
485A
485B
GND
Red
Black
Green
White
Grey
None
Purple
None
None
None
Pink
Blue
Black
6. Power Connection
12V
GND
12V
GND
WD0
WD1
GLED
BEEPER
485A
485B
GND
AC Adapter
DC12V, 1A
Notes:
ŸRecommended : 12V 1A.AC adapter
ŸUse an AC adapter with a higher current
rating to s h a r e powe r with t h e
other devices.

5
Connect the Controller via RS485
Notes:
7.Controller Connection
This ProlD104 reader can be connected to the controller and set by software to
achieve the function. The following is an example of the connection to InBio Pro
controller.
+12V GND
485-
485+
#1 #2 #8
TCP/IP
InBio Pro
485A
485B
DC12V
STATE
PWR
EXT RS485
PC RS485
SWITCH
•If the reader shares the power supply with the device, it is recommended
that the connection between the RS485 interface on the controller and
the reader not exceed 100m. Otherwise, independent power supply is
recommended.
•Before connecting the RS485 reader, you must set the RS485 address of
the reader (device number) via touch key. The odd number indicates the
entry reader and the even number indicates the exit reader.
•InBio Pro controllers can be connected to a maximum of 8 readers, each
reader needs to be powered separately.
•For more information, refer to related user manuals.

6
TCP/IP
TCP/IP
Electric Lock
Door Sensor
InBio Series Controller
ProlD102 ProlD103
Wiegand
STATE
PWR
EXT
RS485
PC
RS485
SWITCH
RS485
PC
5.Standalone Installation
Connect the Controller via Wiegand
12V
GND
WD0
GLED
BEEPER
485A
485B
GND
TCP/IP
ProID104
WD1
InBio Pro
STATE
PWR
EXT RS485
PC RS485
SWITCH
8. Operating Instruction
1.Modify the Administrator Password
Press *# to enter the setting mode and input the administrator password
(1234 by default). After entering the setting mode, the indicator will turn
green. Otherwise, the operation fails.
Press *#→ →0→Input the old administrator password Input the new
password Input the new password→#→ again→#
For Example: *# → 1234 → 0 → 1234567 → # → 1234567 → #
If you forget the administrator password, you can reset the password
by restoring the default settings.
The administrator password contains 1 to 8 characters. After successful
verification, the administrator enters the setting mode.
Note:

7
2. Set the Wiegand Output Mode
Press *#→ Input the administrator password →8→5→0/1/2/3→#
0: Wiegand 26, 1: Wiegand 34(default), 2: reserved, 3: Wiegand 66.
3. Set the Reader Address
Press *#→ Input the administrator password →8→6→1~32→#
Set the reader 485 address. The value ranges from 1 to 32.
4. Set the Keystroke Sound
Press *#→ Input the administrator password →8→7→0~9→#
The number from 0 to 9 corresponds to different sounds.
5. Set the Background Light
Press *#→ Input the administrator password →8→8→0/1/2 →#
0: normally close, 1: normally open, 2: breathing light.
6. Restore the Default Settings
First, remove the screws from the bottom, and then long press the mounting
reset button at the bottom for 4 seconds until the blue indicator lights up four
times, the buzzer rings for four times, and then the buzzer buzzes for one
short time. The device is restored to default settings.
*Images in this guide are for reference only. Refer to the actual product before purchasing.

ZKTeco Industrial Park, No. 32, Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
Copyright © 2023 ZKTECO CO., LTD. All Rights Reserved.