ZKTeco FMB-05 User manual
Installation Guide
Version: 1.0
Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between
the actual product and the written information in this manual.
FMB-05
1
Dimensions
Top Side
Bottom Mounting hole
Unit: mm
45
1302.5
120
160
o
50
120
377
280
1315
270
280
400
1257.5
130.99
120
46
60
60
84
117 116
146
83.5
60
20.5 37
2
How to disassemble the base?
Step 1: Take out the base from its carton.
Step 2: Unscrew the four adjusting screws from the bottom of the base by your
hand.
Step 3: Remove the base plate from the bottom of the base.
Adjusting screw
Base plate
Base
Mounting hole
Fixing hole
Mounting hole: It is used to install the mounting bracket of the device. It can also
be used as a wiring hole.
Fixing hole: Used for xing the mounting bracket of the equipment.
Adjusting screw: It is used to adjust the balance of the equipment.
3
How to connect the mounting bracket with the base?
Step 1: Take out the mounting bracket from its carton.
Step 2: Unscrew the three mounting screws from the bottom of the mounting
bracket by a screwdriver.
Step 3: Fix the mounting bracket and the base with the screws which were
unscrewed from the mounting bracket.
Mounting bracket
Mounting screw
Base
4
Step 4: Fix the base plate to the base with the adjusting screws.
Base plate
Adjusting screw
5
How to connect the device with the mounting bracket?
Step 1: Select the right mounting holes and x the back plate on the mounting
bracket using the mounting screws.
Step 2: Connect the cables to the device.
Step 3: Attach the device to the back plate.
Step 4: Fasten the device to the back plate with a security screw.
Mounting bracket
Back plate
Compatible models: Proface X, Proface X[P], Proface X[TD], Proface XE,
SpeedFace-V5L/V5 Series, SpeedFace-H5L/V5 Series, FaceDepot7B/7BL Series and
Elite Access
Proaface X 1
2
3
4
Network cable
Power cable
DC 12V-3A
Connect to the device
Connect to the device
6
Step 5: After the installation is complete, connect the power cord and network
cable to the device.
DC 12V-3A
Power supply unit
7
Mounting Hole Description for Compatible Models
1
2
3
4
5
678
9
10
11
12
13
14
411
2
6 9
12
Mounting holes 4 & 11 are for installing the SpeedFace-H5/H5L and FaceDepot 7B/7BL.
Mounting holes 4, 8, 11 & 14 are for installing the Elite Access.
Mounting holes 3, 5, 7 & 10 are for installing the Proface X Series.
Mounting holes 2, 6, 9 & 12 are for installing the SpeedFace-V5L/V5.
Mounting holes 1, 6, 9 & 13 are for installing the SpeedFace-V5L[TI].
Please choose dierent mounting holes for fastening the device according to the
back plate of compatible models as shown below:
4
8
11
14
3
5
7
10
1
6 9
13
SpeedFace-H5/H5L
FaceDepot 7B/7BL
Elite Access
Proface X / X[P] / X[TD] / XE SpeedFace-V5L/V5 SpeedFace-V5L[TI]
Copyright © 2020 ZKTECO CO., LTD. All Rights Reserved.
ZKTeco Industrial Park, No. 26, 188 Industrial Road,
Tangxia Town, Dongguan, China.
Phone : +86 769 - 82109991
Fax : +86 755 - 89602394
www.zkteco.com
