Zodiac eXO Installation and operating instructions

H0673400.A - 2019-05
Addendum - Instruc ons Manual - English
External connec ons
Transla on of the original instruc ons in french EN
eXO®/ GenSalt OT/
Hydroxinator® iQ/
Clearwater Duo™

1
EN: WARNING - This product must be serviced by a qualifi ed professional with suffi cient experience in installing and servicing pool equipment to ensure that all
instruc ons given in the product's installa on and user manual are followed to the le er. All safety instruc ons given in the manual must be followed closely to
prevent all risk of injury. Any incorrect installa on and/or improper use shall void the warranty.
EN: WARNING/DANGER - Turn off all switches and the main circuit breaker of the electric circuit for the pool/spa heater before beginning any part
replacement opera on. Failure to comply with these instruc ons may lead to electric shock or cause serious injury or even death. Be careful not to
damage or cause wear to the electrical wiring when connec ng/disconnec ng the wiring in the appliance.
EN: The qualifi ed technician working on the appliance must use/wear personal protec ve equipment (such as safety goggles and
protec ve gloves, etc.) in order to reduce the risk of injury occurring when working on the appliance.
General list of the func ons to be connected
Terminal
block
messages
Type Cable
clamp Func ons eXO® (iQ) GenSalt OT With pH Link or Dual Link
SENS Input - Connec on for the control board
for pH Link and Dual Link modules / /
PUMP Input - Connec on for the pH regula on pump
for pH Link and Dual Link modules / /
CELL Output 1 Connec on for the electroly c cell
UI Output - Connec on for the display
TEMP Input 3 Connec on for the temperature sensor /
Flow Input 2 Connec on for the fl ow switch
iAL RS485 Input 4Func on not used – do not wire / / /
VSP RS485 Output 5 Connec on dedicated to controlling the Zodiac®
variable-speed fi lter pump /
/- Func on not used – do not wire / / /
COVER Input 7 Connec on for the roller shu er/cover for
automa cally managing the LOW func on
SLAVE Output 8 Connec on for an external appliance for the ON/OFF
control of chlorinator (automa c regula on, etc.) /
AUX 2 12-
24V Output 9
Connec on dedicated to the ON/OFF control of a
low-voltage device. This connec on does not power
the device: it manages the ON/OFF func on.
AUX 1 230 V Output 10
Connec on dedicated to the ON/OFF control of a
high-voltage device. This connec on does not power
the device: it manages the ON/OFF func on.
/
PUMP 230V Output 11 Connec on dedicated to the power supply to the
pool fi lter pump.
MAINS Input 12 Mains power supply to the appliance
110-240 VAC - 50/60 Hz
: Connec ons made during manufacture : Mandatory connec ons to be made : Func on to be connected (op onal)

2
EN
External connec ons: what products should be connected?
The chlorinator must be protected by a circuit breaker of the same type as that used for a fi lter pump (for example a
fi ltra on control panel).
If the chlorinator is powered by a fi ltra on control panel, the  mers must be manually set to 24/7 mode. The electrolyser
manages all  mers and must receive a con nuous power supply.
12 - 24 V contact
230 V contact
RS485 cable (supplied
with the pump)
230 V power
supply
230 V power
supply
All types of auxiliary
device
12 - 24 V
All types of auxiliary
device
230 V
FloPro™ VS All fi lter pump models
Transformer for ligh ng,
booster pump, etc.
maximum 8 A
Transformer for ligh ng,
booster pump, etc.
maximum 8 A
Variable-speed pump
maximum 8 A
Single-speed pump or
variable 3-speed pump of
type FloPro™ e3.
maximum 8 A
Connec ng a fi lter pump (depending on the model)
The chlorinator can power and control the fi lter pump.
In such a case, the chlorinator must be powered via an electrical protec on that is calibrated for a fi lter pump.
Possible controls:
- For a single-speed pump (SSP): ON/OFF with 2  mers,
- For a FloPro™ VS variable-speed pump (VSP): ON/OFF/RPM with 4  mers.
(see installa on manual for the Zodiac™
FloPro® VS fi lter pump)
RS485 Cable
(supplied with the
pump) Power supply
230 V
230 V power
supply
FloPro™ VS All fi lter pump models
Variable-speed pump
maximum 8 A
Single-speed pump or
variable 3-speed pump of
type FloPro™ e3.
maximum 8 A
GREEN
YELLOW BLACK
RED
RED BLACK YELLOW
GREEN
(Terminal block at the level of the FloPro™ VS pump)

ZODIAC® is a registered trademark of Zodiac Interna onal, S.A.S.U., used under license.
Zodiac Pool Care Europe - Bd de la Romanerie - BP 90023 - 49180 St Barthélémy d’Anjou cedex France - Simplifi ed joint stock company with sole shareholder and a share capital of €1,267,140 / SIREN 395 068 679 / TCR PARIS
www.zodiac.com
Connec ng to an auxiliary device = AUX1 - Dry contact provided for disconnec on from the 230V power supply
(depending on the model)
The chlorinator manages a dry contact calibrated for disconnec on from the 230V power supply. The power supply
is separated with its own protec on (circuit breaker calibrated to suit the equipment controlled or its transformer –
max. 8 A).
Preferred connec on for NL LED spotlights.
Possible controls: ON/OFF with  mer for all monochroma c spotlights, ON/OFF/Colour with NL RGBW LED spotlights
230 V contact
All types of auxiliary
device
230 V
Transformer for ligh ng,
booster pump, etc.
maximum 8 A
Preferred connec on for Zodiac® NL LED spotlights
(see installa on manual)
: 230 VAC / 12 VAC
(50/60 Hz) transformer
: Electrical protec on
: Auxiliary relay for
external controller or
switch
With 2 spotlights With 1 spotlight
Connec on to an auxiliary device = AUX2 - 12- 24V
The eXO® iQ manages a dry contact calibrated for the12 -24V power supply. The power supply is separated with its
own protec on (circuit breaker calibrated to suit the equipment controlled or its transformer – max. 8 A).
Use a relay (not provided) to be able to control a 230 V device.
Possible controls: ON/OFF
12 - 24 V contact
All types of auxiliary
device
12 - 24 V
Transformer for ligh ng,
booster pump, etc.
maximum 8 A