Zoeller 370-0002 User manual

ATTENTION: READ CAREFULLY BEFORE ATTEMPTING TO INSTALL OR OPERATE YOUR PUMP. PROTECT YOURSELF AND OTHERS
BY OBSERVING ALL SAFETY INFORMATION AND ADDITIONAL INSTRUCTIONS INCLUDED WITH EQUIPMENT. FAILURE TO COMPLY
WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN FOR FUTURE REFERENCE.
SECTION: 6.10.143
FM2340
0711
Supersedes
0110
INSTALLATION INSTRUCTIONS
These installation instructions are applicable for Model 370-0002 Aeration/Fountain Pump only.
This pump system is designed for decorative use and can improve water aeration.
PREINSTALLATION CHECKLIST - ALL INSTALLATIONS
AERATION/FOUNTAIN PUMP MODEL 370-0002
SEE BELOW FOR LIST OF WARNINGS
1. Make certain that the power source conforms to the requirements of
the equipment as stated on the product nameplates and wire motor for
correct voltage. See motor nameplate.
2. Periodically inspect the pump for damage and perform routine
maintenance as required.
3. The maximum temperature of the pumped liquid must not exceed 120°F.
4. Supply voltage must be with in +/- 10% of nameplate voltage. Incorrect
voltage can cause re or seriously damage motor and voids warranty. If
in doubt, consult a licensed electrician.
REFER TO WARRANTY ON PAGE 2.
SEE BELOW FOR LIST OF CAUTIONS
Product information presented
here reects conditions at time
of publication. Consult factory
regarding discrepancies or
inconsistencies.
MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347
SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961
[phone] • 1 (800) 928-PUMP • FAX [phone]
visit our web site:
www.zoeller.com
®
Your Peace of Mind is Our Top Priority
®
1. Make sure that the pump is plugged into a properly grounded
electrical receptacle. Use an Underwriters Laboratory listed circuit
analyzer to test for proper installation of the circuit and ground.Any service
to circuits or receptacles should be conducted by a qualified licensed
electrician.
2. Do not remove the ground pin from the plug under any circumstances.
If the ground pin is damaged, replace the power cord or plug before use.
3. All electrical installations must conform to the requirements of the National
Electric Code and all local codes.
4. System furnished with a 100 ft. power cord with 3-prong GFCI plug; must
connect to properly grounded receptacle of grounding type. Do not
remove ground pin on plug. Do not extend the cord length by splicing
or with an extension cord.
5. Disconnect power before servicing the pump or motor by unplugging
the unit from the outlet.
6. Do not touch the motor when operating and allow the motor
to cool before touching.
7. Pump is built to handle clear water only; it is not designed to handle water
containing sand, silt, or other abrasives.
8. Do not use to pump flammable or explosive fluids such as
gasoline, kerosene, fuel oil, etc. Do not use in flammable
and/or explosive atmospheres.
9. Do not use this product in hazardous environments or
anywhere a spark could potentially ignite explosive gases.
10. Do not handle this product with wet hands or while standing in water
or on a wet or damp surface.
11. Units are supplied with an automatically resetting thermal overload
device and can restart without warning.
12. Provide a means of pressure relief if the pump discharge
can be shut off or obstructed. Pumps operating against a
closed discharge can create very hot pumped liquid, which
can cause burns.
13. “No swimming” and/or warning signs should be posted per state and
local codes. Please affix included warning label to power receptacle
or junction box.
14. Do not ground to a gas supply line.
15. Protect the power cable from coming in contact with sharp objects, oil,
grease, hot surfaces, or chemicals. DO NOT kink the power cable. If
damaged, replace immediately.
16. According to the state of California (Prop 65), this product contains
chemicals known to the state of California to cause cancer and birth
defects or other reproductive harm.
17. NEVER leave the control box, fused disconnect switch or cover open
(either partially or completely) when not being worked on by a competent
electrician.
18. Water leaving nozzle is at a high velocity and can cause bodily injury
if contact is made.
19. Never examine, make wiring changes, or touch the motor before
disconnecting the main electrical supply switch. The thermal device
may have opened the electrical circuit. All motors should be equipped
with a correctly fused disconnect switch to provide protection. Consult
local or United States National Electrical Codes for proper fuse protection
based on motor data chart.
20. GFI plug must be oriented with cord coming out of the bottom and
protected from direct rainfall.
021766

© Copyright 2011. All rights reserved.
2
Manufacturer warrants, to the purchaser and subsequent owner during
the warranty period, every new product to be free from defects in material
and workmanship under normal use and service, when properly used
and maintained, for a period of one year from date of purchase by the
end user, or 18 months from date of original manufacture of the product,
whichever comes rst. Parts that fail within the warranty period, one year
from date of purchase by the end user, or 18 months from the date of
original manufacture of the product, whichever comes rst, that inspections
determine to be defective in material or workmanship, will be repaired,
replaced or remanufactured at Manufacturer's option, provided however,
that by so doing we will not be obligated to replace an entire assembly,
the entire mechanism or the complete unit. No allowance will be made
for shipping charges, damages, labor or other charges that may occur
due to product failure, repair or replacement.
This warranty does not apply to and there shall be no warranty for any
material or product that has been disassembled without prior approval
of Manufacturer, subjected to misuse, misapplication, neglect, alteration,
accident or act of God; that has not been installed, operated or maintained
in accordance with Manufacturer's installation instructions; that has been
exposed to outside substances including but not limited to the following:
sand, gravel, cement, mud, tar, hydrocarbons, hydrocarbon derivatives
(oil, gasoline, solvents, etc.), or other abrasive or corrosive substances,
washtowelsorfeminine sanitary products, etc. inallpumpingapplications.
LIMITED WARRANTY
Thewarrantysetout in the paragraph aboveisinlieu of all other warranties
expressed or implied; and we do not authorize any representative or other
person to assume for us any other liability in connection with our products.
Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky
40211, Attention: Customer Service Department to obtain any needed
repair or replacement of part(s) or additional information pertaining to
our warranty.
MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR
SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES OR
BREACH OF EXPRESSED OR IMPLIED WARRANTY; AND
ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE AND OF MERCHANTABILITY SHALL BE LIMITED
TO THE DURATION OF THE EXPRESSED WARRANTY.
Somestatesdonot allow limitations on the duration ofanimpliedwarranty,
so the above limitation may not apply to you. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
This warranty gives you specic legal rights and you may also have other
rights which vary from state to state.
ELECTRICAL PRECAUTIONS- Before servicing a pump, always shut off the main power breaker and then unplug the
pump. Make sure you are not standing in water and are wearing insulated protective sole shoes. Under ooded conditions, contact your
local electric company or a qualied licensed electrician for disconnecting electrical service prior to pump removal.
TROUBLE SHOOTING GUIDE
SAFETY INSTRUCTIONS
Carefully read and follow all safety instructions in this manual and
on pump. Keep safety labels in good condition. Replace missing or
damaged safety labels.
This is a SAFETY ALERT SYMBOL. When you see this
symbol on the pump or in the manual, look for one of the
following signal words and be alert to the potential for
personal injury or property damage.
Warns of hazards that WILL cause
serious personal injury, death, or major
property damage if ignored.
Warns of hazards that CAN cause serious
personal injury or death if ignored.
Warns of hazards that MAY cause minor
personal injury, product or property
damage if ignored.
IMPORTANT: Indicates factors concerned with operation, installation,
assembly or maintenance which could result in damage to the machine
or equipment if ignored.
NOTE: Indicates special instructions which are important but not
related to hazards.
!
SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION
Unit won’t run. Circuit breaker tripped. Reset circuit breaker.
GFCI tripped. Reset GFCI
No or low spray. Blocked screen or nozzle, missing or damaged
o-ring, or incorrectly installed nozzle
Disconnect power.
Clean screen and/or nozzle. Check that o-ring
is undamaged and seated in groove. Check that
nozzle is installed properly. (nozzles are marked
This side up”). Check depth of pond. If less than
5’ deep, move to deeper section. Restart unit.
GFCI trips. Electrical storm can trip GFCI. Reset GFCI.
Short in system. Disconnect power and inspect cord for damage.
If cord is damaged contact Customer Service
Help Line at 1-800-928-7867.
Unit spins. Anchor rope loose Check anchor rope and re-attach if necessary

© Copyright 2011. All rights reserved.
3
INSTALLATION
1. Only install this system in ponds where no swimming, wading,
boating, or shing is allowed. Disconnect power to the pump
before shing or entering the water.
2. Post appropriate warning signs per local and state codes.
3. Inspect pump system for damage before installing in pond. Check
that all bolts and screws are tight. Check for any bent prongs or a
cracked case on the GFCI.
4. The unit ships with one spray nozzle attached. To change to one
of the other two nozzles, remove the four screws from the nozzle
then replace with the desired nozzle. Refer to Figures 2, 3, and 4
for spray pattern appearance. Nozzles are marked “This side up.”
Make sure the o-ring is seated in the groove before installing
nozzle. Tighten screws until seated, approximately 10 to 12 in-lbs.
5. Attach nylon anchor ropes to two eyebolts located at top of screen.
Secure (make sure rope is tight) to weights placed on pond oor
or stakes on pond shore. When using weights to anchor the pump,
place weights approximately ten feet from unit, 180 degrees apart.
6. Before connecting the unit to the power receptacle, check to
ensure there is no leakage to the ground. This can be done by
using an ohm meter and setting the scale to the highest setting
(i.e. Rx100K). Connect one ohm meter lead to the unit power
cord ground (round prong) and to one of the at prongs. It should
read innite or at least two megohms. Repeat with the other
prong. If reading is below two megohms on either prong, contact
Technical Service Help Line at 800-928-7867.
7. Do Not Operate System on an Extension Cord! If no power is
accessible at the pond, contract a licensed electrician to install the
proper power supply in accordance with the National Electrical
Code and all applicable local codes and ordinances.
8. After installing the unit, checking ground and connecting power to
the unit, the unit can be powered up. Check operation of the
GFCI by pushing the “Test” button, the unit should stop. Pushing
the “Reset” button should restart the unit. If pressing the “Test”
button does not stop the unit, immediately shut off power to the
unit and contact Technical Support Help Line at 800-928-7867.
IL0535
Pond Pump Float
Nylon rope secured to weights
can be attached to stakes on
shore. 2 Required.
5 Feet Minimum Depth
Approved outdoor grounded
receptacle with GFI protected plug
Power cord may require
burial. Refer to local codes
15 - 20
Feet
Figure 1: Typical Installation
Figure 3: Water Lily - An eye-catching combination spray. Part #2A Figure 4: Water Trumpet - A symmetrical inverted bell-shape. Part #2C
INSTALLATION CHECK LIST
 Read installation instructions and warnings.
 Post appropriate warning signs.
 Install desired spray nozzle.
 Install and anchor unit in pond.
 Check insulation resistance to ground.
 Power up unit.
 Test operation of GFCI by pressing the “Test” button.
 File instructions for future reference.
REQUIRED TOOLS AND SUPPLIES
l#2 Phillips screwdriver to change nozzles.
lNylon rope to anchor unit.
lStakes or weights for anchoring unit.
lOhm meter to check insulation resistance to ground.
WINTER STORAGE
lRinse unit with clean water to remove any build-up on unit.
l
Check unit for any damage.
lStore unit in heated space in freezing climates.
The pump motor is water lubricated and is factory lled with an anti-
freeze solution. During operation the antifreeze might exchange, thru
the ltered check valve, with the pond water. In climates where freezing
may occur, the unit must be stored in a heated storage space to prevent
damage to the motor
Figure 2: Sky Cannon - A dramatic single plume of water. Part #2B

© Copyright 2011. All rights reserved.
4
INTERNAL PARTS
15
16
11
1
2(A/B/C)
3
4
5
6
7
17
10
9
11
13
12
14
1
15
11
8
Flow (GPH) Spray Height
(Ft.)
Pattern
Image
Pattern
Name
4900 15
T
h
i
s
s
i
d
e
u
p
IL0537
T
h
i
s
s
i
d
e
u
p
T
h
i
s
s
i
d
e
u
p
Water Lily
- 2A
3300 15 Sky Cannon
- 2B
2700 13 Water
Trumpet - 2C
Item # Qty Part No. Description
1 6 021766 Screw - #10 x 3/4 Slotted Head or Pan Head
Sheet Metal Screw (18-8 Stainless Steel)
2A 1 021617 Nozzle - Water Lily
2B 1 021618 Nozzle - Sky Cannon
2C 1 021619 Nozzle - Water Trumpet
3 1 021622 O-Ring - AS568A - 041 (3” ID x 3/18” OD)
4 6 021628 Bolt - SS 1/4-20 x 3/4
5 6 021629 Lockwasher - 1/4”
6 1 021707 Mounting Flange
7 1 021534 Float
8 1 021713 Pump End
9 1 021740 Motor 1/2 HP 115V
10 4 127021 Locknut - SS 5/16-24
11 1 021715 100 ft. power cord with GFI
12 2 021609 Eye Bolt - SS 1/4-20 x 2-1/2
13 2 021623 Locknut - SS 1/4--20
14 1 021608 Screen
15 1 021611 Screen Cap
16 1 021613 Strain Relief
17 2 021625 Warning Decal
*Standard hardware item, available locally
5
4
IL0536
IL0538