Zoning Zity Operating and maintenance instructions

ES
EN
FR
IT
217741
ZITY zoning system
Quick installation manual
P.O. BOX 5
08540 Centelles (Barcelona)
T [phone]
www.zoning.es
Technical Support Service:
Tel. [phone]

Contents
2Manual del usuario V 09/18
Technical characteristics and warranty ............................... 3
Connection of system components ...................................... 4
System configuration ............................................................. 8
Learning and start-up ........................................................... 10
Most common errors ............................................................ 11
WEE (WEEE)
Do not dispose of Electrical and Electronic Devices as household waste.
These devices should be taken away for recycling. Act according to the
legislation in force.
Quick installation guide
NOTES ON RADIO TRANSMISSION
The central control unit should preferably be located in a high place and away from metal masses and conductive
elements. Otherwise, the range between the thermostats and the central control unit may be reduced.
Radio transmission does not take place on an exclusive frequency, so the possibility of interference cannot be
excluded. Frequency inhibitors and radio equipment operating in a permanent transmission mode in the same
frequency band (433 MHz) may impair the normal operation of the ZONING. The system is designed to work on two
different frequencies (433.92 and 434.33 MHz) to minimise this type of problem.
The installation should be carried out by authorised personnel only. Perform the entire
installation without supply voltage. Protect the equipment with the usual devices.

ZITY, quick installation guide (for air zoning installations)
v 0.V 09/18 TAGBASE 3
ES
Technical characteristics and warranty
MADEL ATD hereby declares that the ZOE / ZEBRA / ZITY
equipment complies with the essential requirements and
any other applicable or enforceable provisions of Directives
2014/35/EU LVD, 2014/30/EU EMC and 2014/53/UE RED,
2011/65/EU ROHS, 2001/95/EC General product safety,
2012/19/UE RAEE and Regulation 1907/2006 REACH.
ZITY central control unit
• Power 230 VAC/50-60 Hz
• ZITY consumption: 6 VA
• Mean range Radio: 50 m in open field, 20 m in habitat.
• Orientable external antenna.
• Frequency 434.33 MHz (Optional: 433.92 MHz). Work
cycle <10%
• For installation up to 2000 m above sea level.
• Receiver, CAT II.
• 230 VAC/5A relay outputs (maximum load: 5A, cos φ
=1)
• Protection grade: IP 20
• Electrical insulation protection, CAT II
• Operating temperature: 0ºC to 55ºC
• Storage temperature: -10 ºC to 60 ºC
• Dimensions (LxHxZ): 160x90x65 mm
• Weight 0.5 kg
ZOE Thermostat
• Power 2 1.5 V LR06 AA batteries (alkaline)
• Average battery life 1 year (or longer). The batteries are
supplied with the unit
• Battery life indicator.
• Carrier frequency (ISM band, Standard I-ETS 300-220):
433.34 MHz (Optional: 434.92 MHz)
• Mean range: 50 m in open field, 20 m in habitat
• Operating temperature: 0ºC to 55ºC
• Storage temperature: -10 ºC to 60 ºC
• Humidity Range: 10-90% (no condensation)
• Wall mount with bolts (supplied)
• Protection grade: IP 20
• NTC10K Temperature sensor. Accuracy 0.1ºC
• Configurable control hysteresis +/-0.2 to 0.5°C
• CA control accuracy according to Standard EN15500.
CA=0.3 (Test report CLMS17-741. CSTB)
• Economy ECO mode (±3ºC setpoint temperature
variation)
• Frost protection for T<7ºC+/-3ºC
• Dimensions (LxHxZ): 70x110x19 mm
• Weight 0.13 kg (with batteries)
ZEBRA Thermostat
• Power supply: 12 VDC
• Consumption: < 0.3 VA
• Control output: Modbus RTU Rs485
• Wiring: S <1.5 mm2
• Operating temperature: 0ºC to 50ºC
• Storage temperature: -20 ºC to 60 ºC
• Humidity Range: 10-90% (no condensation)
• Wall mount with bolts (supplied)
• Protection grade: IP 20
• NTC10K Temperature sensor. Accuracy 0.1ºC
• CA control accuracy according to Standard EN15500.
CA=0.4 (Test report CLMS17-742. CSTB)
• Economy ECO mode (±3ºC setpoint temperature
variation)
• Frost protection for: T<7ºC+/-3ºC
• Dimensions (LxHxZ): 85x108x13 mm
• Weight 0.11 kg
WARRANTY
MADEL ATD guarantees all its products against production
defects for a period of two (2) years. This period will start from the
date of delivery of the merchandise to the DISTRIBUTOR. The
warranty will only cover replacement of defective products, not
including labour, travel, replacement of other damaged products,
etc., or any other disbursement, expenses or consequential
damages. The warranty will not cover the damage incurred in the
products due to incorrect installation, handling or storage in poor
conditions.
The procedure to follow in the case of return under warranty of the
equipment of the Madel ZONING system is the following: If there
is any problem, you should contact the MADEL technical support
service (902.550.290) who will try to solve any problems and
answer any questions about the installation. It is important to call
from the place where the equipment is installed in order to carry
out the necessary tests to diagnose the equipment. If any
anomaly is detected, the return of the equipment for factory
inspection will be authorised. Our technical support will provide a
written authorisation for the return of the equipment under
warranty. This authorisation can only be completed by Madel
technical staff and should be attached to the equipment. It will also
serve for monitoring its return, which should be made through
your usual distributor.
All returned equipment must be in perfect conditions of use and
must have all the initial additional components, such as sensors,
aerial, etc.

ZITY central control unit
4Manual del usuario V 09/18
1 Connection of system components
1-A Direct expansion system with radio gateway
A trademark of
www.zoning.es
ID :0025
Serial no: CCASSNNN
FW:
V.XX
R
radio
IP :0xx
Bus Remote
- RC
A tra
d
em
a
rk of
www.zon
i
n
g
.es
I
D
:
0
025
S
er
i
a
l
n
o
:
C
C
A
SS
NN
N
FW:
V.XX
R
ra
d
i
o
IP
:0
x
x
Bus Remote
PP
- R
C
Rx Tx
5V 12V COM
DC Power Output
-
+
Zone 1
-
+
Zone 2
-
+
Zone 3
-
+
Zone 4
-
+
Zone 5
-
+
Zone 6
Com1 Com2R1 R2 R3 R4 R5 R6 R7
Rs485/Rem
GND A B
Rs485 / Loc
GND A B
Digital Inputs
Com 1
2
1 2 3 4 5 6 7 8
Relay
Tx 1 2
Zones
3456
1234 56 7
Selecting Switch
SW1 -
12V
+
DC Power
Output
NTC 2 NTC 1
POWER SUPPLY
230 VAC/50 Hz/1
1234
ON
1234
ON
1234
ON
5678
AC Unit
BOX
I.U. INTERFACE
Rs485
A B
SET
DAY
PROG
COPY
INFO
CLEAR
ECO
FRESH
M A D E L
SONDA / SENSOR
NTC 2
A/C Unit
Damper 1.1
M
ZOE -RC thermostat
ZONE 1 ZONE 2 ZONE 3
M
Damper 1.2
*
*Maximo 2 compuertas por zona *Maximum 2 dampers per zone
To Indoor AC Unit
Refer to Interface Manual
1234
ON
1234
ON
1234
ON
5678
AC Unit
BOX
I.U. INTERFACE
Rs485
A B
SET
DAY
PROG
COPY
INFO
CLEAR
ECO
FRESH
M A D E L
SET
DAY
PROG
COPY
INFO
CLEAR
ECO
FRESH
M A D E L
ZOE-RC thermostat ZOE-RC thermostat
ON/OFF (1)
U N I T
22ºC
REMOTE CONTROL
(2)
(3)
R/C ANTENNA
NETBOX: Wifi Interface
(optionnal)
Damper 1.1
M
M
Damper 1.2
*
Damper 1.1
M
M
Damper 1.2
*
POWER
SUPPLY
230 VAC
A
B
R
x
Tx
5
V
12V
C
O
M
D
C
P
o
wer Outpu
t
-
+
Z
o
ne 1
-
+
Z
o
ne
2
-
+
Zo
ne
3
-
+
Z
o
ne
4
-
+
Zo
ne
5
-
+
Zo
ne
6
C
o
m1 C
o
m2
R
1
R
2
R
3
R
4
R
5
R
6
R7
(1) Only for ON/OFF installations with no Interface (2) Consult the Interface installation manual according to brand and model (3) NTC 2 Probe: leave the default resistance, only install for systems with NO interface or in FUJITSU units- It must be installed on the RETURN Fig. 1 Connection diagram ZITY-RC + ZOE-RC + Interface
PROBE
Maximum 2 gates per zone

ZITY, quick installation guide (for air zoning installations)
v 0.V 09/18 TAGBASE 5
ES
1-B Direct expansion system with wired gateway
M A D E L
MODE FAN UP DOWN
POWER
M A D E L
MODE FAN UP DOWN
POWER
ZEBRA Wired Thermostat
ZONE 1 ZONE 2 ZONE 3
ZEBRA Wired Thermostat
M A D E L
MODE FAN UP DOWN
POWER
ZEBRA Wired Thermostat
A trademark of
www.zoning.es
ID :0025
Serial no: CCASSNNN
FW:
V.XX
R
radio
IP :0xx
Bus Remote
- RC
A tra
d
em
a
rk of
www.zon
i
n
g
.es
I
D
:
0
0
25
S
er
i
a
l
n
o
:
C
C
A
SS
NNN
FW:
V.XX
R
ra
d
i
o
IP
:
0
x
x
Bus Remote
P
P
- R
C
Rx Tx
5V 12V COM
DC Power Output
-
+
Zone 1
-
+
Zone 2
-
+
Zone 3
-
+
Zone 4
-
+
Zone 5
-
+
Zone 6
Com1 Com2R1 R2 R3 R4 R5 R6 R7
Rs485/Rem
GND A B
Rs485 / Loc
GND A B
Digital Inputs
Com 1
2
12345678
Relay
Tx 1 2
Zones
3456
1234 56 7
Selecting Switch
SW1 -
12V
+
DC Power
Output
NTC 2 NTC 1
POWER SUPPLY
230 VAC/50 Hz/1
1234
ON
1234
ON
1234
ON
5678
AC Unit
BOX
I.U. INTERFACE
Rs485
A B
SONDA
NTC 2
A/C Unit
Damper 1.1
M
M
Damper 1.2
*
*
ano
zrop
satr
e
up
m
o
c2
om
i
xaM
*
en
o
z
r
eps
repma
d
2
mumixaM
To Indoor AC Unit
Refer to Interface Manual
1234
ON
1234
ON
1234
ON
5678
AC Unit
BOX
I.U. INTERFACE
Rs485
A B
ON/OFF (1)
U N I T
22ºC
REMOTE CONTROL
(2)
(3)
NETBOX: Wifi Interface
(optionnal)
Damper 1.1
M
M
Damper 1.2
*
Damper 1.1
M
M
Damper 1.2
*
POWER
SUPPLY
230 VAC
A
B
R
x
Tx
5
V
12V
C
O
M
D
C
P
o
wer Outpu
t
-
+
Z
o
ne
1
-
+
Z
o
ne
2
-
+
Zo
ne
3
-
+
Z
o
ne
4
-
+
Zo
ne
5
-
+
Zo
ne
6
C
o
m
1
C
o
m
2
R
1
R
2
R
3
R
4
R
5
R
6
R7
**
ONLY ZEBRA V2 for ZITY V5
M
OC
1T
N
I
2TN
I
V
2
1
D
N
G
A
B
*
**
SEE COLORS
**
ONLY ZEBRA V2 for ZITY V5
MOC
1T
N
I
2
TN
I
***
ONLY ZEBRA V2 for ZITY V5
MO
C
1T
N
I
2TN
I
*
12V
GND
A
B
COM
INT1 INT2
ZEBRA V1 ZEBRA V2
**
ZEBRA WIRE COLORS
Orange
Blue
Black
Red
-- -- --
Green
Black
Red
White
Yellow
Orange
Brown
V
21
D
N
G
A
B
V
2
1
D
NG
A
B
(1) Only for ON/OFF installations with no Interface (2) Consult the Interface installation manual according to brand and model (3) NTC 2 Probe: leave the default resistance, only install for systems with NO interface or in FUJITSU units- It must be installed on the RETURN
Fig. 2 Connection diagram ZITY-W + ZEBRA + Interface xxxBOX
** ZEBRA WIRE COLORS
ZEBRA V1 ZEBRA V2
12V+ Blue Red
GND– Orange Black
ARed Green BBlack White
COM -- Yellow
INT1 -- Orange INT2 -- Brown
Maximum 2 gates per zone
PROBE

ZITY central control unit
6Manual del usuario V 09/18
1-C Fan-Coil system 2 and 4 pipes via radio
A trademark of
www.zoning.es
ID :0025
Serial no: CCASSNNN
FW:
V.XX
R
radio
IP :0xx
Bus Remote
- RC
A tr
ad
e
m
a
rk of
www.zoning.e
s
ID
:
0
025
Serial no
:
C
C
A
SS
NN
N
FW:
V.X
X
R
rad
i
o
IP
:0
x
x
Bus Remote
PP
-
R
C
Rx Tx
5V 12V COM
DC Power Output
-
+
Zone 1
-
+
Zone 2
-
+
Zone 3
-
+
Zone 4
-
+
Zone 5
-
+
Zone 6
Com1 Com2R1 R2 R3 R4 R5 R6 R7
Rs485/Rem
GND A B
Rs485 / Loc
GND A B
Digital Inputs
Com 1
2
1 2 3 4 5 6 7 8
Relay
Tx 1 2
Zones
3456
1234 56 7
Selecting Switch
SW1 -
12V
+
DC Power
Output
NTC 2 NTC 1
POWER SUPPLY
230 VAC/50 Hz/1
SET
DAY
PROG
COPY
INFO
CLEAR
ECO
FRESH
M A D E L
Damper 1.1
M
ZOE -RC thermostat
ZONE 1 ZONE 2 ZONE 3
M
Damper 1.2
*
*Maximo 2 compuertas por zona *Maximum 2 dampers per zone
SET
DAY
PROG
COPY
INFO
CLEAR
ECO
FRESH
M A D E L
SET
DAY
PROG
COPY
INFO
CLEAR
ECO
FRESH
M A D E L
ZOE-RC thermostat ZOE-RC thermostat
ON/OFF (1)
R/C ANTENNA
NETBOX: Wifi Interface
(optionnal)
Damper 1.1
M
M
Damper 1.2
*
Damper 1.1
M
M
Damper 1.2
*
POWER
SUPPLY
230 VAC
A
B
R
x
Tx
5
V
12V
C
O
M
D
C
P
o
wer Out
p
ut
-
+
Zo
ne
1
-
+
Z
o
ne
2
-
+
Z
o
ne
3
-
+
Zo
ne
4
-
+
Zo
ne
5
-
+
Z
o
ne
6
C
om1
C
om
2
R
1
R
2
R
3
R
4
R
5
R
6
R7
FAN-COIL Wiring
4 Pipes - 3 Fan speeds
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
N
AF
TAE
H
/LOOC.V
FF
O
/N
O
LO
O
C/TAEH
L
N
0-10 V
KBY
+-
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
NAF
TAEH/LOOC.V
FFO/
N
O
L
OOC
/ TA
EH
L
N
2 Pipes - 3 Fan speeds
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
NAF
LOO
C
.
V
TAEH.V
FF
O
/NO
LOO
C / TAE
H
L
N
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
L
OOC.V
TAE
H
.
V
FFO/NO
LOO
C
/TAE
H
L
N
NAF
2 Pipes - 0-10V 4 Pipes - 0-10V
0-10 V
KBY
+-
SONDA / SENSOR
NTC 1/2 (3)
KBY: EC 0-10V Fan control

K B Y
Pressure Control
Sw1
SET
Rs485
AB
0-10V
DAMPER
PRESSURE
SENSOR
L1
12
ON
1
0
3
4
5
6
72
FAN
0-10 V
(optionnal)
(2)
(1) Consult detailed diagram according to type of installation. (2) KBY. Constant pressure control module: see KBY installation manual. (3) NTC1 / NTC2 Probes. Optional connection. See attached configuration table. (4) ON/OFF: Stop/Start output external unit. (5) HEAT/COOL: 4-way valve output. ON: COOL; OFF: HEAT.
Fig. 3 Connection diagram ZITY-RC + ZOE-RC + Hydronic Fan-Coil
(3) For fan-coil water inlet temperature protection (4) Do not install and remove the default resistance. If installed,
the Master must be removed. The cold-heat change is carried out automatically with the temperature measured by the NTC2 in the water inlet pipe.
2-Pipe Fan-Coil
Installation
Type Individual Collective Location
NTC1 Optional
(3)
Optional
(3)
Battery inlet
pipe
NTC2 Do not install
(4)
Optional
(3)
Battery inlet
pipe
4-Pipe Fan-Coil
Installation
Type Individual Collective Location
NTC1 Optional
(3)
Optional
(3)
Heat battery
inlet pipe
NTC2 Optional
(3)
Optional
(3)
Cold battery
inlet pipe
Maximum 2 gates per zone
PROBE

ZITY, quick installation guide (for air zoning installations)
v 0.V 09/18 TAGBASE 7
ES
1-D Wired Fan-Coil system 2 and 4 pipes
M A D E L
MODE FAN UP DOWN
POWER
M A D E L
MODE FAN UP DOWN
POWER
ZEBRA Wired Thermostat
ZONE 1 ZONE 2 ZONE 3
ZEBRA Wired Thermostat
M A D E L
MODE FAN UP DOWN
POWER
ZEBRA Wired Thermostat
A trademark of
www.zoning.es
ID :0025
Serial no: CCASSNNN
FW:
V.XX
R
radio
IP :0xx
Bus Remote
- RC
A
t
r
ad
e
m
a
rk of
w
ww.zon
i
n
g
.e
s
I
D
:
0
0
2
5
Ser
i
a
l
n
o
:
C
C
A
SSNN
N
FW:
V.XX
R
rad
i
o
IP
:
0xx
Bus Remote
P
P
-
R
C
Rx Tx
5V 12V COM
DC Power Output
-
+
Zone 1
-
+
Zone 2
-
+
Zone 3
-
+
Zone 4
-
+
Zone 5
-
+
Zone 6
Com1 Com2R1 R2 R3 R4 R5 R6 R7
Rs485/Rem
GND A B
Rs485 / Loc
GND A B
Digital Inputs
Com 1
2
1 2 3 4 5 6 7 8
Relay
Tx 1 2
Zones
3456
1234 56 7
Selecting Switch
SW1 -
12V
+
DC Power
Output
NTC 2 NTC 1
POWER SUPPLY
230 VAC/50 Hz/1
Damper 1.1
M
M
Damper 1.2
*
*
a
no
zropsatreupmoc
2omixaM
*
e
no
z
r
epsrepmad2mumixaM
ON/OFF (1)
NETBOX: Wifi Interface
(optionnal)
Damper 1.1
M
M
Damper 1.2
*
Damper 1.1
M
M
Damper 1.2
*
POWER
SUPPLY
230 VAC
A
B
R
x
Tx
5
V
12V
C
O
M
DC
P
o
w
er
O
ut
p
ut
-
+
Z
one
1
-
+
Z
one
2
-
+
Zone
3
-
+
Z
one
4
-
+
Z
one
5
-
+
Zone
6
C
om
1
C
om
2
R
1
R
2
R
3
R
4
R
5
R
6
R7
KBY: EC 0-10V Fan control

K B Y
Pressure Control
Sw1
SET
Rs485
AB
0-10V
DAMPER
PRESSURE
SENSOR
L1
12
ON
1
0
3
4
5
6
72
FAN
0-10 V
(optionnal)
(2)
FAN-COIL Wiring
4 Pipes - 3 Fan speeds
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
N
A
F
TAEH/LOOC.V
FFO
/N
O
LOOC/TAEH
L
N
0-10 V
KBY
+-
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
N
A
F
TAEH/LOOC.V
FFO/NO
L
OOC
/
TAEH
L
N
2 Pipes - 3 Fan speeds
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
NAF
LOOC.V
TAEH.V
FFO/NO
LOOC/TAEH
L
N
www.zoning.es
Com1 Com2R1 R2 R3 R4 R5 R6 R7
LOOC.V
TAEH.V
FFO
/NO
LOOC/TAEH
L
N
NA
F
2 Pipes - 0-10V 4 Pipes - 0-10V
0-10 V
KBY
+-
SONDA / SENSOR
NTC 2 (3)
NTC 1
12V
GND
A
B
COM
INT1 INT2
ZEBRA V1 ZEBRA V2
**
ZEBRA WIRE COLORS
Orange
Blue
Black
Red
-- -- --
Green
Black
Red
White
Yellow
Orange
Brown
**
ONLY ZEBRA V2 for ZITY V5
MOC
1T
N
I
2T
NI
V
2
1
DN
G
A
B
*
**
SEE COLORS
**
ONLY ZEBRA V2 for ZITY V5
M
OC
1TNI
2TNI
*
V
2
1
DN
G
A
B
V
21
D
NG
A
B
**
ONLY ZEBRA V2 for ZITY V5
M
OC
1TNI
2TNI
*
(1) Consult detailed diagram according to type of installation. (2) KBY. Constant pressure control module: see KBY installation manual. (3) NTC1 / NTC2 Probes. Optional connection. See attached configuration table. (4) ON/OFF: Stop/Start output external unit. (5) HEAT/COOL: 4-way valve output. ON: COOL; OFF: HEAT.
Fig. 4 Connection diagram ZITY-W + ZEBRA + Hydronic Fan-Coil
** ZEBRA WIRE COLORS
ZEBRA V1 ZEBRA V2
12V+ Blue Red
GND– Orange Black
ARed Green BBlack White
COM -- Yellow
INT1 -- Orange INT2 -- Brown
(3) For fan-coil water inlet temperature protection (4) Do not install and remove the default resistance. If installed,
the Master must be removed. The cold-heat change is carried out automatically with the temperature measured by the NTC2 in the water inlet pipe.
4-Pipe Fan-Coil
Installation
Type Individual Collective Location
NTC1 Optional
(3)
Optional
(3)
Heat battery
inlet pipe
NTC2 Optional
(3)
Optional
(3)
Cold battery
inlet pipe
2-Pipe Fan-Coil
Installation
Type Individual Collective Location
NTC1 Optional
(3)
Optional
(3)
Battery inlet
pipe
NTC2 Do not install
(4)
Optional
(3)
Battery inlet
pipe
Maximum 2 gates per zone
PROBE

ZITY central control unit
8Manual del usuario V 09/18
2 System configuration
2-A Configuration with ZOE-RC thermostats (via radio)
1Configure the central control unit: select switch SW1 according to the type of machine and position DIP8 in learning mode
(DIP8 down).
2Connect the thermostats and the central control unit, via the following steps:
To perform the steps described, it is necessary to access the Se1 menu of the ZOE-RC thermostat. See the following
diagram:
3Learning and start-up: see section 3 to carry out this process.
A trademark of
www.zoning.es
ID :0025
Serial no: CCASSNNN
FW: V.XX
R
radio
IP :0xx
Bus Remote
- RC
A
tra
d
e
m
a
r
k o
f
w
ww.zoning.es
ID
:
0
0
2
5
Ser
i
a
l
no
:
C
C
ASSNNN
F
W: V.X
X
R
rad
i
o
IP
:
0x
x
Bus Remote
P
P
- R
C
Rx Tx
5V 12V
COM
DC Power Output
-
+
Zone 1
-
+
Zone 2
-
+
Zone 3
-
+
Zone 4
-
+
Zone 5
-
+
Zone 6
Com1 Com2R1 R2 R3 R4 R5 R6 R7
Rs485 / Rem
GND A B
Rs485 / Loc
GND A B
Digital Inputs
Com 1
2
Relay
Tx 1 2
Zones 3456
1234 56 7 Selecting Switch
SW1
- 12V +
DC Power
Output
NTC 2 NTC 1
12345678
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Direct expansion 2-Pipe Fan-Coil 4-Pipe Fan-Coil
A trademark of
www.zoning.es
ID :0025
Serial no: CCASSNNN
FW:
V.XX
R
radio
IP :0xx
Bus Remote
- RC
A
tr
ad
e
m
a
r
k
o
f
w
ww.zonin
g
.es
ID
:
0
0
2
5
Ser
i
a
l
no:
C
C
A
SS
NNN
FW:
V.XX
R
r
a
d
i
o
IP
:
0
x
x
Bus Remote
P
P
-
R
C
Rx Tx
5V 12V
COM
DC Power Output
-
+
Zone 1
-
+
Zone 2
-
+
Zone 3
-
+
Zone 4
-
+
Zone 5
-
+
Zone 6
Com1 Com2R1 R2 R3 R4 R5 R6 R7
Rs485 / Rem
GND A B
Rs485 / Loc
GND A B
Digital Inputs
Com 1
2
1 2 3 4 5 6 7 8
Relay
Tx 1 2
Zones 3456
1234 56 7 Selecting Switch
SW1
-
12V
+
DC Power
Output
NTC 2 NTC 1
ID
•Locate on the front label the ID number (radio ID) of the ZITY central control
unit and associate this number to each of the thermostats.
•Assign a zone number to each thermostat (corresponding to the motorized
control that has been connected to outputs 1 to 6 of the ZITY central control
unit).
•Select whether the thermostat is Master or Slave. In each system, it is
compulsory to set a single thermostat as Master. If there is no Master or
there is more than one, the ZITY central control unit will be in error.
Z
MASTER
MASTER
OFF
OFF
ON
ON
SYST
SYST
ECO
PROG
PROG
1 2 3 4 567
2468
10
10
12
12
14
14
16
16
18
18
20
20
22
22
24
24
ºC
TIMER
TIMER
Z
MASTER
MASTER
OFF
OFF
ON
ON
SYST
SYST
ECO
PROG
PROG
1 2 3 4 567
2468
10
10
12
12
14
14
16
16
18
18
20
20
22
22
24
24
ºC
TIMER
TIMER
Z
MASTER
MASTER
OFF
OFF
ON
ON
SYST
SYST
ECO
PROG
PROG
1234567
2468
10
10
12
12
14
14
16
16
18
18
20
20
22
22
24
24
ºC
TIMER
TIMER
Z
MASTER
MASTER
OFF
OFF
ON
SYST
SYST
ECO
PROG
1234567
246810 12 14 16 18 20 22 24
ºC
TIMER
TIMER
Z
MASTER
MASTER
OFF
ON
ON
SYST
SYST
ECO
PROG
PROG
1234567
246810 12 14 16 18 20 22 24
ºC
TIMER
TIMER
ON/OFF
Z
MASTER
MASTER
OFF
ON
SYST
SYST
ECO
PROG
PROG
1234567
246810 12 14 16 18 20 22 24
ºC
TIMER
TIMER
ON/OFF ON/OFF
Z
MASTER
MASTER
OFF
ON
SYST
SYST
ECO
PROG
PROG
1234567
246810 12 14 16 18 20 22 24
ºC
TIMER
TIMER
Z
MASTER
MASTER
OFF
ON
ON
SYST
SYST
ECO
PROG
PROG
1234567
246810 12 14 16 18 20 22 24
ºC
TIMER
TIMER
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
INFO
CLEAR
SET
DAY
PROG
COPY
ECO
FRESH
Access the SE1 menu:
press SET-DAY
Access the SE1 menu:
press + key
Access the SE1 menu:
press ON/OFF key
Select C-SP mode
Select ID No. Select Zone No. Select Master/Slave Record and Exit

ZITY, quick installation guide (for air zoning installations)
v 0.V 09/18 TAGBASE 9
ES
2-B Configuration with ZEBRA thermostats (wired)
1Configure the central control unit: select switch SW1 according to the diagram. There are two ZEBRA thermostat models:
V1, 4-wire thermostat; V2: 7-wire thermostat.
2Connect the thermostats and the central control unit, via the following steps:
• For the Master Thermostat: define a single Master per installation.
Configure menus 5 (Master/Slave), 6 (Flexifan), 9 (Active Modes), 12 (Zone Number) and 14 (Keypad Lock):
• For the Slave Thermostat: only configure menus No. 5 (Slave) and No. 12 (zone number):
For more information about the rest of the menus, consult the advanced technical manual.
3Learning and start-up: see section 3 to carry out this process.
A trademark of
www.zoning.es
ID :0025
Serial no: CCASSNNN
FW: V.XX
R
radio
IP :0xx
Bus Remote
- RC
A
tra
d
e
m
a
r
k o
f
w
ww.zoning.es
ID
:
0
0
2
5
Ser
i
a
l
no
:
C
C
ASSNNN
F
W: V.X
X
R
rad
i
o
IP
:
0x
x
Bus Remote
P
P
- R
C
Rx Tx
5V 12V
COM
DC Power Output
-
+
Zone 1
-
+
Zone 2
-
+
Zone 3
-
+
Zone 4
-
+
Zone 5
-
+
Zone 6
Com1 Com2R1 R2 R3 R4 R5 R6 R7
Rs485 / Rem
GND A B
Rs485 / Loc
GND A B
Digital Inputs
Com 1
2
Relay
Tx 1 2
Zones 3456
1234 56 7 Selecting Switch
SW1
- 12V +
DC Power
Output
NTC 2 NTC 1
12345678
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Direct expansion 2-Pipe Fan-Coil 4-Pipe Fan-Coil
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
FAN
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
FAN
FANFAN
FAN
( )( )
( ) ( ) ( )
3s
3s x4
x3 x3 (x5)
x2
For more information about programming, see the ZEBRA thermostat manual
Turn off thermostat
(OFF mode)
Access
configuration
Go to menu 5 Access the
parameter
Master/Slave:
place in position 1
Flexifan: place in
ON position
Go to menu 09 Access the
parameter
Active Modes:
place in position 2
V1: go to menu 12
(V2: go to menu 14)
Access the
parameter
Zone No.: select zone
No.
V1: go to menu 14
(V2: go to menu 16)
Access the
parameter
Type of Locking:
place in position 0
Confirm and Exit
FAN FAN
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
POWER
UP DOWNFANMODE
ID
FAN
( ) ( )
3s
3s x12
(x14)
Turn off the
thermostat
Access
configuration
V1: go to menu 12
(V2: go to menu 14)
Access the
parameter
Zone No.: select
zone No.
Confirm and Exit

ZITY central control unit
10 Manual del usuario V 09/18
3 Learning and start-up
In the first place, it is necessary to carry out the appraisal
process in order to detect all the system's elements and
later (once recognized) the start-up can be carried out.
Make sure that DIP8 is OFF
(down).
3.1 Recognition of components –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
1Connect the 230VAC power supply of the ZITY central
control unit.
2The central control unit is
positioned in learning
mode and the 7 LEDs
corresponding to the
relays begin to flash.
3Every time the thermostat
of one of the zones is
recognised by the central
control unit, the LED
corresponding to the zone
lights up in green.
The upper row of LEDs
corresponds to peripheral
detection. Each time one of
them is detected, the
corresponding LED goes out.
For direct expansion machines, the LED R1 corresponding
to the communication interface must be off.
For Fan-Coil type machines, no LEDs should be off.
Consult the advanced technical manual to see how the rest
of the LEDs should correspond with the peripherals.
3.2 Exit from learning mode –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
3.3 Start-up in normal operating mode –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
1Raise the voltage to the ZITY central control unit again.
2When power is supplied to the central control unit it will
begin to operate normally according to the configuration
specified in the SW1.
3.4 Check operation ––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Check the operation of all zones by following this table:
3.5 Adjusting the by-pass gate
If mechanical bypass is available, proceed as follows:
1Leave the smallest area open
2Move the counterweight until the gate opens and no
noise is generated in the grilles. The closer the
counterweight is to the gate is, the more it will open, the
farther it is the more it will close.
1Wait 30 seconds after the last component has been detected.
2Raise the DIP8
3Cut the voltage to the ZITY central control unit.
123 4 5
Select 18ºC on all
thermostats
Check that all
grilles open
Wait for the machine
to start from cold
Select 30ºC on all
thermostats
Check that all grilles
close and the machine
stops
Select 30ºC on all
thermostats
Check that all
grilles open
Wait for the machine
to start from warm
Select 18ºC on all
thermostats
Check that all grilles
close and the machine
stops