Zoom F8 Mounting instructions

F8 Firmware Update Guide
Copyright(C) 2021 ZOOM Corporation. All Rights Reserved.
Copying or reprinting this manual in part or in whole without permission is prohibited.
Windows® is a registered trademark of Microsoft® Corporation.
Mac® is a trademark or registered trademark of Apple Inc.
Note: All trademarks and registered trademarks in this document are for identification purposes only and are not
intended to infringe on the copyrights of their respective owners.
Proper display is not possible on grayscale devices.
The illustrations in these instructions might differ from actual screens.
● Zoom Corporation does not bear liability for any damages or third-party
claims arising from the use of the software, whether directly or indirectly.
Unauthorized redistribution, sale, leasing, renting, alteration, or reverse
engineering of the software is prohibited. Features and specifications of the
software and the contents of the documentation may be changed in future
without notice.

2
This guide explains firmware update to Ver. 6.10 as an example.
Download the ZIP file containing the firmware update file from F8 download page.

3
■For Windows
1. Extracting the ZIP file.
Select the folder where you downloaded the ZIP file. ① Click "Compressed Folder Tools", then
② "Extract All". The ZIP file will be extracted.
Folder_A
Folder_C
Folder_D
Folder_D 󰴧
Folder_C
MyFolder
󰴦
2. Copying the firmware update file to a SD card.
Copy the “F8SYSTEM.BIN” file to the root directory on a SD card.
The firmware update file
Copy the firmware update
file to the USB flash drive.
F8_v6.10E.zip
F8SYSTEM.BIN
F8_System
Software Version
History_610_en.pdf
F8_v6.10
This PC > Downloads > F8_v6.10
This PC > Downloads > F8_v6.10
F8_v6.10
F8SYSTEM.BIN
F8_System
Software Version
History_110_en.pdf
F8SYSTEM.BIN
F8_SD
Copy the firmware update
File to a SD Card.
The firmware update file
SD Card
F8_SD
F8_SD
3
F8_Firmware_Upd
ate_Guide_E.pdf
F8_Firmware_Upd
ate_Guide_E.pdf

4
■For Mac
1. Opening the downloaded file.
After downloading, click "Downloads" displayed at the bottom of the screen. Then click ➁ to open
the downloaded file.
󴨙
󰴦
2. Copying the firmware update file to a SD card.
Copy the “F8SYSTEM.BIN” file to the root directory on a SD card.
The firmware update file Copy the firmware update
file to a SD card.
SD card
F8_v6.10E
F8_v6.10E
F8_System_
Softwar…10_en.pdf
F8SYSTEM.BIN
F8SYSTEM.BIN
ate_Guide_E.pdf
F8_Firmware_Upd

5
The following is the same procedure for Windows and Mac.
1. Insert the SD card into the SD CARD 1 slot.
2. Install new batteries in the F8 or connect the AC adapter.
3. Turn the power on while pressing .
NOTE
・Always make certain that the power is off when inserting or removing a SD card. Inserting or
removing a card while the power is on could result in data loss.
・When inserting a SD card, be sure to insert the correct end with the top side up as shown.
NOTE
・If the SD card is loaded in the SD CARD 2 slot, eject it before updating.
②
①

6
4. Use to select “Yes” and press .
5. After the update completes, turn the power off.
NOTE
・During the firmware update, do not turn the power off or remove the SD card. It could cause the
F8 to be unstartable.
・In the unlikely event that a firmware update should fail, conduct the procedures from the
beginning to update the firmware again.

7
Check the Firmware Version.
1. Press .
2. Use to select “SYSTEM” and press .
3. Use to select “Firmware Version”, and press .
Check the Firmware Version displayed on the screen.
©2021 ZOOM CORPORATION Z2I- 4251-01