ZooZ ZAC93 User manual

800 Z-WAVE GPIO MODULE
ZAC93
USER MANUAL
FEATURES
ŸZ-Wave Plus Static Controller to easily
add Z-Wave communication to your
smart home ecosystem
ŸLatest S2 security protocol for a truly
private network
Ÿ800 Series Long Range Z-Wave for fast,
low-power direct communication
ŸExtended range up to a mile in open
space when using Long Range
ŸDesigned for Raspberry Pi and Home
Assistant Yellow hardware
SPECIFICATIONS
ŸModel Number: ZAC93
ŸZ-Wave Frequency: 908.42 MHz
ŸPower: 3.3 VDC
ŸSDK: 7.18.01
ŸOperating Temperature: 32-104° F
ŸOperating Humidity: Up to 85%
ŸInstallation and Use: Indoor only
ŸDimensions: 1.1" x 1.1"
SET-UP
Use this 800 Series Z-Wave Plus GPIO
Module as a wireless radio for your host
controller, such as Raspberry Pi. Follow the
detailed instructions in the link below to
connect the module. Please proceed with
caution when installing the device.
Once the controller is set up and connected
to your home automation soware, you can
enjoy a fully secure, private Z-Wave Plus
mesh network. If the soware supports Z-
Wave Long Range, enable direct
communication between your devices and
the controller for supreme range up to 1
mile and a larger network size up to 4000
nodes.
Questions? [e-mail]
GPIO MODULE AS SECONDARY CONTROLLER
You can use the GPIO module as a
secondary controller to your current Z-Wave
system if it accepts additional controllers.
To enroll the module in your current system,
send the inclusion command and put the
module into learning mode, using the
SerialAPI mode in the interface.
www.getzooz.com
FACTORY RESET
The GPIO Module can only be reset by the
host soware while it’s in SerialAPI mode.
The device is reset once an appropriate
command from the host soware is sent to
reset the Z-Wave network.
There is no way to manually reset the
module without a connection to the host
soware.
Scan to register your
product for extended
warranty, priority
customer service, and
more perks.
www.getzooz.com/register
Scan the code with your
phone’s camera and click
on the link to access
detailed installation
instructions for the GPIO
module.

WARNINGWARNING
ŸThis product should be installed indoors
upon completion of any building
renovations.
ŸDo not install the device in a place with
direct sun exposure, high temperature, or
humidity.
ŸKeep away from chemicals, water, and
dust.
ŸEnsure the device is never close to any
heat source or open flame to prevent fire.
ŸEnsure the device is connected to an
electric power source that does not
exceed the maximum load power.
ŸNo part of the device may be replaced or
repaired by the user.
This product is covered under a standard 12-
month warranty and an extended 5-year
limited warranty once registered. To read the
full warranty policy or file a warranty claim,
please go to:
www.getzooz.com/warranty
REGISTER YOUR PRODUCT HERE:
www.getzooz.com/register
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY
RA D I O O R T V I N T E R F E R E N C E C A U S E D BY
UNAUTHORIZED MODIFICATIONS TO T H I S
EQUIPMENT. SUCH MODIFICATIONS COULD VOID
THE USER’S AUTHORITY TO OPE RATE THE
EQUIPMENT. STORE INDOORS WHEN NOT IN USE.
SUITABLE FOR DRY LOCATIONS ONLY. DO NOT
IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY
EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference
received, including interference that may cause
undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed and
used according to instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will
not occur in any given installation.
If this equipment causes harmful interference to
radio or television reception, the user may try to
correct the interference by taking one or more of the
following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and
receiver
- Connect equipment into a separate outlet or
circuit from receiver
- Consult the dealer or an experienced radio/TV
technician for additional assistance
All brand names displayed are trademarks of their
respective holders.
© Zooz 2022
WARRANTY
This product can be included and operated
in any Z-Wave network with other Z-Wave
certified devices from other manufacturers
and/or other applications. All non-battery
operated nodes within the network will act
as repeaters regardless of vendor to increase
reliability of the network.
This product features the latest Security 2
(S2) framework to remove smart home
network hacking risks. This de-vice is
equipped with a unique authentication
code for trusted wireless communication.
S2