ZoraBots Robin User manual

BY
User Manual
docs.zorabots.be

01
BY
User Manual
docs.zorabots.be
Checklist User Manual
Power adapter x 1
(Design of adapter could
di er from EU/UK/US
standard, picture may be
di erent from the real
delivery)
Type-C cable x 1
SIM card eject pin x 1User Manual x 1
Robin x 1

02 Quick Guide User Manual
Follow the instructions on the application on your mobile device.
Android and Google Play are trademarks of Google LLC.
App Store is a service mark of Apple Inc.
iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is
used under license.
Download and install the ZBOS
Software of ZoraBots.
Search for the ZBOS Control app in the App Store or Google Play or scan
the QR code to download the app on your mobile device.

02 Quick Guide User Manual
Turn your Robot on
• Put the Robin on a table and bend his knees;
• Press and hold his power button until the LED light (his mouth) is on.
Link your Robin
• Open the ZBOS app. Select your Robot and log in with your account
• Follow the instructions on the app to connect your Robin to the
internet for the binding process.
Turn your Robin o
• Press and hold the power button for 3 seconds until your Robin is o;
Tips:
Wait for about 40 seconds. When the Robin says “I am ready”, you can
start using him.

03 Feature Introduction User Manual
SIM card and network service
• The Robot support one nano SIM card and 4G network.
Install a SIM Card
• Turn o your Robin and locate the SIM card slot under his left
armpit. Push a SIM eject tool into the small hole next to the SIM slot
with a little force to pull the SIM tray out.
• Properly place your SIM card on the tray and follow the instructions
below to slide the tray back into your Robin.

04 Do’s User Manual
Grab your Robin properly: Use the handy grips of your Robin to pick
him up.
If your Robin is in sleep mode or turned o while charging, please
place the Robin in the pose shown below.

05 Don’ts User Manual
Do not touch your Robin when he is moving to
avoid hand injuries.
Do not twist or pull Robin’s head with
force.
Do not twist the joints of your Robin
with force.
Do not place your Robin at the edge of
a table.
Do not put your Robin on an inclined
surface.
Do not throw or smash your Robin to
prevent damage.

06 Hardware User Manual
Camera
LCD eyes
LED mouth
Infrared sensor
Microphone SIM slot
Stereo speakers

06 Hardware User Manual
Volume button
Power button
Handy grip
Type-C interface
Sling hole

06 Hardware User Manual
Microphone
array
Microphone
array
Touch sensor

07 Buttons and Lights User Manual
Power button
Press and hold Press and hold for 3 seconds to turn your Robin on or o.
Press Press the power button to check the battery level after turning on
your robot or during the charging process.
Volume button
Increase or decrease the volume of your Robin.
Touch sensor on the head
Tap your Robot on the forehead to stop the current action.
Long press to activate the voice recognition.
Double head tap: scan QR code
Triple head tap: say IP address
LED Light in mouth
While light is ickering Your Robin is turned on.
Flash red light 3 times
every once in a while Your Robin is oine.
Flickering red light Your Robin is turned o and charging (Robin battery < 50%).
Flickering green light Your Robin is turned o and charging (50% ≤ Robin
battery< 100%).
Constant green light Your Robin is o and fully charged.

08 Product Specications User Manual
Product name AlphaMini Robot
Product model Alpha Mini
Measurements
Height 245mm, Width 149mm, Thickness 112mm (The actual
size may vary slightly depending on the conguration,
manufacturing process, and measurement method)
Weight About 700g
Joints 14 joints in total
(3 head joints, 4 arm joints, 1 waist joint, 6 leg joints )
Network
standard 4G/3G
Transmission
function WiFi 2.4G (WLAN 80211 b/g/n), BT4.2, GPS
User storage
RAM2GB/ROM16GB
(As the Android system has taken up a certain storage, the user
storage may be less than this value.)
SIM card type Nano SIM card (4FF, single card slot)
Speakers 2-channel stereo speakers, O.8W*2
Microphones 4-microphone array (used for voice interaction and source
location), 1 communication microphone
Display screen 1.22 inch (actual visible area is slightly smaller), 262K color
TFT display screen, 240*240 pixels
Camera 13 million pixels
Sensors GPS, accelerometer, gyroscope, touch sensor, Infrared sensor
Battery Li-Polymer lithium polymer battery, 3,85v, 4060mAh (Typical)
Power adapter
Manufacturer: Jiangxi Jian Aohai Technology Co.,Ltd.
Model: A138A-120150U-EU4 / A138A-120150U-UK4
Input AC 100V-240V-50/6OHz O.5A;
Output DC 5V 3A/9V 2A/12V 1,5A
Operating
temperatures 0*C-40*C
Control methods Power button, volume button, App, voice control

08 Product Specications User Manual
Mode Frequency Max Emission Power (dBm)
Bluetooth 2402MHz-2480MHz 9.532
BLE 2402MHz-2480MHz 1.146
Wlan 2,4G 2412MHz-2472MHz 16.8
LTE Band1
Uplink:1922.4MHz-1977.6MHz
22.04
Downlink:2112.4MHz-2167.6MHz
LTE Band3
Uplink:1710MHz-1785MHz
21.89
Downlink:1805MHz-1880MHz
WCDMA Band1
Uplink:1922.4MHz-1977.6MHz
21.68
Downlink:2112.4MHz-2167.6MHz
WCDMA Band8
Uplink:882.4MHz-912.6MHz
22.16
Downlink:927.4MHz-957.6MHz

09 Precautions User Manual
• Store this product in a well-ventilated, clean, and dry environment to avoid
moisture, dust, and high temperatures, which may damage the product.
• Turn o the product before cleaning it, Wipe its surface with a small amount of
neutral detergent and a damp towel. Dry it naturally before turning it on again.
• When not using this product, please turn it o and put it into the product storage
box. Charge the product at least once a month to avoid shortening the life of the
battery.
• When charging this product, please use the original power adapter and cable,
Please consult support.zorabots.be before replacing a power adapter or a cable.
• When the battery is fully charged, please unplug the charger immediately to avoid
unnecessary damage to the battery caused by overcharging.
• This product has a built-in lithium battery. If the battery life is exhausted (when it
fails to reach 80% after repeated charging or exhausts 100% of its power reserve
within 15 minutes), please contact support.zorabots.be to ask for professional help.
• When using this product, please place it on a hard horizontal surface and do not
hinder its movement. This product needs at least 20cm of clear space above, in
front, at the rear, and on both sides.
• When using this product, do not place it at the edge of a surface high above the
oor to avoid damage caused by falling.
• Movable joints of this product are all precision parts. Do not twist, pull or squeeze
them with force to avoid damage.
• When using this product, it is recommended to operate the designated parts of the
product by hand (as illustrated in the instructions above) when it is still.
Grasping/operating non-designated parts when the product is moving may cause
nger injuries.
• Do not disassemble, ret, and repair this product by yourself. If your product
needs to be repaired, please contact support.zorabots.be.
• This product only supports ocial upgrades. Please do not upgrade the
softwares/software systems in other ways to avoid damage or user information
leakage.
• In abnormal situations (such as start-up failure, shutdown failure, no response
from the robot, or abnormal actions, etc.), please contact support.zorabots.be.

!WARNING:
1 ) The packaging must be retained since it contains important information.
2) The battery charger used with the toy are to be regularly examined for damage
to the cord, plug, enclosure and other parts, and in the event of such damage,they
must not be used until the damage has been repaired.
3) The supply terminals, battery terminals and connectors are not to be
short-circuited.
4) Misuse of transformer can cause electrical shock.
5) The Robot must only be used with the recommended transformer (rated output
DC5V, 3A). The transformer is not a toy.
6) Choking hazard - small parts inside. The Robot is not intended for children under
3 years old.
7) The Robot must be disconnected from the transformer before cleaning.
8) Transformers and power supplies for Robots are not intended to be used as toys,
and the use of these products by children shall be under the full supervision of
parents.
9) Be care for hazardous function sharp point on the end of the pin.
10) The batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, re or the like.
Attention should be drawn to environmental aspects of battery disposal.
11) Only use attachments/accessories specied or provided by the manufacturer
(such as the exclusive supply adapter, battery etc).
12) Do not touch the toy when it is moving to avoid hand injuries.
13) Disposal of a battery into re or a hot oven, or mechanically crushing or cutting
of a battery, that can result in an explosion.
14) Leaving a battery in an extremely high temperature surrounding environment
that can result in an explosion or the leakage of ammable liquid or gas.
15) A battery subjected to extremely low air pressure that may result in an
explosion or the leakage of ammable liquid or gas.
16) Keep at least 20cm distance when using the robot.

CAUTION: Danger of explosion if battery is incorrectly replaced, Replace only with
the same or equivalent type.
means all the safety and operating instructions should be read before
this product is operated.

EU Declaration of Conformity
We UBTECH ROBOTICS CORP LTD
Address: 16th and 22nd Floor, Block C1, Nanshan I Park, No.1001 Xueyuan Road,
Nanshan District, Shenzhen City, P.R. CHINA.
declare under our sole responsibility that the product
Product Name: AlphaMini Robot
Model name: Alpha Mini
Software: V1.6.0.50
Accessories: Adapter 1:
Model name: A138A-120150U-EU4
Input:100-240V-50/6OHz 0.5A
Output:5V 3A/9V 2A/12V 1.5A
Adapter 2:
Model name: A138A-120150U-UK4
Input:100- 240V˜50/6OHz O.5A
Output:5V 3A/9V 2A/12V 1.5A
comply with the following directives and regulations:
2014/53/EU (The Radio Equipment Directive)
For the evaluation of the compliance with these Directives and Regulations, the
following standards/requirements were applied:
The conformity assessment procedure as referenced in Article 17 and detailed in Annex Ill of the
Radio equipment Directive has been followed with the involvement of a noti ed body:
Noti ed Body: TUV SUD TPS
NB No.: 0123
certi cate No.: TPS-RED50005O i01
Responsible for making this declaration is the:
Manufacturer
Authorised representative established within the EU
Person responsible for making this declaration
Print name/Title: Wavne cheng/Senior Certi cation Engineer
Shenzhen China
(Place)
2019-8-16
(Date) (Signature)
Safety
Article 3.1(a) EN 62368-1:2014/411:2017
EMC
Article 3.1(b)
EN 55032:2012
EN 55032:2015
EN 55035:2017
Draft EN 301 489-1 V2.2.1:2019-03
Draft EN 301 489-17 V3.2.0:2017-03
EN 301 489-19 V2.1.1.2019-04
Draft EN 301 489-52 V.1.1.0:2016-11
Radio
Article 3.2
EN 300 328 V2.1.1:2016
EN 303 413 V1.1.1
EN 301 908-01 V11.1.1
EN 301 908-02 V11.1.2
EN 301 908-13 V11.1.2
Health
Article 3.1(a)
EN 62479:2010
EN 50663:2017
EN 62311:2008
EN 50665:2017

ZoraBots
Archimedesstraat 17, 8400 Oostende, Belgium
www.zorabots.be