Zotac ZBOX nano C Series User manual

ZOTAC ZBOX nano
1
ZOTAC ZBOX nano
User’s Manual
No part of this manual, including the products and software described in it, may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form or by any means, except documentation kept by the
purchaser for backup purposes, without the express written permission of ZOTAC.
Products and corporate names mentioned in this manual may be registered trademarks
or copyrights of their respective companies, and are used for identication purposes
only. All trademarks are the property of their respective owners.
Every effort has been made to ensure that the contents of this manual are correct and
up to date. However, the manufacturer makes no guarantee regarding the accuracy of
its contents, and reserves the right to make changes without prior notice.
CAUTION:
Risk of explosion if the battery is replaced with an incorrect type. Batteries should be
recycled where possible. Disposal of used batteries must be in accordance with local
environmental regulations.

ZOTAC ZBOX nano
2
Table of Contents
Product specications ----------------------------------------------------------------------------------------3
Safety information ----------------------------------------------------------------------------------------------4
Setting up your system-------------------------------------------------------------------------------------4
Care during use ----------------------------------------------------------------------------------------------4
Welcome -----------------------------------------------------------------------------------------------------------5
Package contents -------------------------------------------------------------------------------------------5
Getting to know your ZOTAC ZBOX nano --------------------------------------------------------------6
Front view -----------------------------------------------------------------------------------------------------6
Rear view ------------------------------------------------------------------------------------------------------7
Customizing the ZOTAC ZBOX nano ---------------------------------------------------------------------8
Installing a memory module-------------------------------------------------------------------------------9
Removing the memory module --------------------------------------------------------------------------10
Installing a 22/42 M.2 SATA SSD------------------------------------------------------------------------11
Installing a hard disk drive --------------------------------------------------------------------------------15
Setting up your ZOTAC ZBOX nano ----------------------------------------------------------------------18
Positioning the ZOTAC ZBOX nano-----------------------------------------------------------------------20
Mounting the ZOTAC ZBOX nano to an LCD monitor ---------------------------------------------20
Installing drivers and software -----------------------------------------------------------------------------22
Installing an operating system----------------------------------------------------------------------------22
Installing system drivers -----------------------------------------------------------------------------------22
Using your ZOTAC ZBOX nano-----------------------------------------------------------------------------23
Conguring a wireless connection ----------------------------------------------------------------------23
Conguring audio output-----------------------------------------------------------------------------------24

ZOTAC ZBOX nano
3
Product specications
Processor
• AMD Ryzen 3 Mobile 3200U (dual-core 2.6GHz,up to 3.5GHz) for ZBOX CA621NANO
Onboard graphics
• AMD Radeon™ Vega 3 Graphics
• HDMI 2.0 (max resolution:4096x2160 @60Hz)
• DP 1.4 (max resolution:3840x2160 @60Hz)
Memory support
• 2 x DDR4-2400 SODIMM Slot
• Up to 32 GB of memory
USB ports
• Front 1 x USB3.0 port
• Rear 3 x USB3.0 ports
Storage support
• SATA Gen3 Data transfer rate up to 6.0 Gb/s
• Supports 1 x 2.5-inch SATA HDD/SSD
• Supports 1x M.2 2242 Key-M SATA SSD
Network support
• Dual 10/100/1000 Mbps Ethernet
• IEEE 802.3 compatible
Wi-Fi support
• 802.11ac Wi-Fi (dual-band)
• Bluetooth 4.2
Onboard Audio
• Stereo analog audio output and Microphone input
Operating System support
• Windows 10 64-bit
Product Dimensions
• 204mm x 129mm x 68mm

ZOTAC ZBOX nano
4
Safety information
Your ZOTAC ZBOX nano is designed and tested to meet the latest standards of safety for information
technology equipment. However, to ensure your safety, it is important that you read the following safety
instructions.
Setting up your system
Read and follow all instructions in the documentation before operating your system.
Do not use this product near water or a heat source such as a radiator.
Set up the system on a stable surface.
Openings on the chassis are for ventilation. Do not block or cover these openings. Make sure
you leave plenty of space around the system for ventilation. Never insert objects of any kind into
the ventilation openings.
Use this product in environments with ambient temperatures between 0℃and 35℃.
 If you use an extension cord, please use the UL listed cord and make sure that the total
ampere rating of the devices plugged into the extension cord does not exceed its ampere
rating.
Care during use
Do not walk on the power cord or allow anything to rest on it.
Do not spill water or any other liquids on your system.
When the system is turned off, a small amount of electrical current still ows. Always unplug all
power, modem, and network cables from the power outlets before cleaning the system.
If you encounter the following technical problems with the product, unplug the power cord and
contact a qualied service technician or your retailer.
¾The power cord or plug is damaged.
¾Liquid has been spilled onto the system.
¾The system does not function properly even if you follow the operating instructions.
¾The system was dropped or the cabinet is damaged.

ZOTAC ZBOX nano
5
Welcome
Congratulations on your purchase of the ZOTAC ZBOX nano. The following illustration displays the
package contents of your new ZOTAC ZBOX nano. If any of the below items is damaged or missing,
contact your retailer.
Package contents
• 1 x ZOTAC ZBOX nano
• 1 x VESA mount
• 1 x AC Adapter
• 1 x Power Cord
• 1 x Antenna
• 1 x Support DVD (optional)
• 1 x USB ash drive with OS drivers
• 1 x User Manual & Quick Start Guide
• 1 x Warranty Card

ZOTAC ZBOX nano
6
Getting to know your ZOTAC ZBOX nano
Front view
Refer to the diagram below to identify the components on the front of the ZBOX nano
1. Power button
The power button turns the system ON and OFF.
2. Power LED
The Power LED is always ON when power is on.
3. SATA status LED
The SATA LED blinks when data is being written onto or read from the SATA.
4. Wi-Fi status indicator
The Wi-Fi LED is always ON when data is being transfered over Wi-Fi.
5. Memory card reader
The built-in memory card reader reads SD/SDHC/SDXC cards used in devices such as digital
cameras, MP3 players, mobile phones and PDAs.
6. Headphone/Audio Out jack
The stereo headphone jack (3.5mm) is used to connect the system’s audio out signal to
amplied speakers or headphones.
7. Microphone jack
The microphone jack is designed to connect a microphone for video conferencing, voice
narrations or simple audio recordings.
8. USB 3.0 port
The USB 3.0 port supports the SuperSpeed USB 3.0 devices and is backwards compatible
with USB 2.0/1.1 devices. Use this port for USB 3.0 devices for maximum performance with
USB 3.0 compatible devices.
1
234
56 7
8

ZOTAC ZBOX nano
7
Rear view
Refer to the diagram below to identify the components on the back of the system.
1. WiFi antenna connector
The WiFi antenna connector supports the included WiFi antenna.
2. Ethernet ports
The eight-pin RJ-45 LAN port supports standard Ethernet cable for connections to local area
networks (LAN) with speeds of 10/100/1000Mbps.
3. USB 3.0 port
The USB 3.0 port supports the SuperSpeed USB 3.0 devices and is backwards compatible
with USB 2.0/1.1 devices. Use this port for USB 3.0 devices for maximum performance with
USB 3.0 compatible devices.
4. USB 3.0 ports
Compatible to USB 3.1 devices for maximun performance with USB3.0 spec. The USB 3.0
port supports the SuperSpeed USB 3.0 devices and is backwards compatible with USB
2.0/1.1 devices. Use this port for USB 3.0 devices for maximum performance with USB 3.0
compatible devices.
5. DisplayPort
DisplayPort supports both external (box-to-box) and internal (laptop LCD panel) display con-
nections.
6. HDMI port
The HDMI (High Denition Multimedia Interface) port supports a UHD device such as an LCD
TV or monitor to allow viewing on a larger external display.
7. Power input (DC19V)
The supplied power adapter converts AC power to DC power for use with this jack. Power
supplied through this jack supplies power to the PC. To prevent damage to the PC, always
use the supplied power adapter.
The power adapter may become warm to hot when in use. Do not cover the adapter and keep it away from your body.
4
1
2
3
5
6
7

ZOTAC ZBOX nano
8
Customizing the ZOTAC ZBOX nano
Before installing hardware, please follow the instructions below to remove the cover of your
ZOTAC ZBOX nano.
1. Remove the four thumb screws securing the bottom cover into place.
2. Remove the bottom cover.

ZOTAC ZBOX nano
9
Installing a memory module
1. Locate the SO-DIMM memory slots and insert a SO-DIMM memory module into the slot
at a 45 degree angle.
2. Gently press down on the memory module until it locks into place by the arms of the
memory slot.
Note: This ZOTAC ZBOX nano accomodates two DDR4 SO-DIMM memory modules. You must install at least one module
for the system to function. PLUS / Windows models include memory pre-installed.

ZOTAC ZBOX nano
10
Removing the memory module
1. Locate the SO-DIMM memory slot and gently press the two arms securing the memory
module outwards, as shown in the image below, to release the memory module.
2. Remove the memory module from the slot at a 45-degree angle.

ZOTAC ZBOX nano
11
Installing a 22/42 M.2 SATA SSD
1. Remove 4 screws highlighted from the chassis bracket (tool required) and set them
aside in a safe place.
2. Gently lift up the chassis bracket and set it aside in a safe place.

ZOTAC ZBOX nano
12
3. Release the screw from the M.2 SSD slot as shown and set it aside.
4. Insert the M.2 SSD into the slot at a 45 degree angle.

ZOTAC ZBOX nano
13
5. Gently push down on the M.2 SSD and secure it in place with the screw.
6. Orient the chassis bracket as shown and gently place it down onto the unit.

ZOTAC ZBOX nano
14
7. Secure the chassis bracket down with the 4 screws

ZOTAC ZBOX nano
15
2. Install the hard disk bracket onto a 2.5-inch SATA hard disk drive / SSD with 2 screws.
Installing a hard disk drive
1. Locate the hard disk bracket, remove the 2 screws, and remove the hard disk bracket as
shown in the image below.
*PLUS / Windows models include SSD pre-installed.

ZOTAC ZBOX nano
16
4. Reinstall the screws for the hard disk bracket.
3. Insert the hard disk drive / SSD into the socket and gently slide into the connector.

ZOTAC ZBOX nano
17
Note:
1. After installing the hard disk drive / SSD and memory module, please remove the
corresponding protective lm.
2. The thermal pad is default for 7mm height HDD / SSD, if you use a 9.5mm hard
disk drive / SSD, please make sure to remove the thermal pad for the HDD / SSD.
for HDD/SSD
for the lower
memory slot
for the top
memory slot

ZOTAC ZBOX nano
18
Setting up your ZOTAC ZBOX nano
Please connect your peripherals before using your ZOTAC ZBOX nano
1. Connecting the WiFi antenna
Connect the WiFi antenna to the WiFi antenna connector.
2. Connecting to a network device
Connect one end of a network cable to the LAN port on the system rear panel and the other
end to a network hub, switch or router.
3. Connecting to USB 3.0 devices
Connect USB 3.0 devices such as external hard disk drives, SSDs and ash drives to the USB
3.0 port on the system rear panel.
1
3456
2
1
2
3 3
4
56

ZOTAC ZBOX nano
19
4. Connecting a DisplayPort display
Connect the DisplayPort connector to the DP port of the monitor or display.
5. Connecting to an HDMI display
Connect one end of an HDMI cable to an HDTV or monitor, and the other end to the HDMI
port on the system rear panel.
6. Connecting the power adapter and turning on the ZBOX nano
Connect the supplied AC adapter to the DC IN jack on the system rear panel and then press
the power switch on the front panel to turn on the system.
When your ZOTAC ZBOX nano is not in use, unplug the power adapter or switch off the
AC outlet to conserve power.