Zotac ZBOX series User manual

1
ZOTAC ZBOX
ZOTAC ZBOX
User’s Manual
No part of this manual, including the products and software described in it,
may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language in any form or by any means,except documenta-
tion kept by the purchaser for backup purposes, without the express written
permission of ZOTAC.
Products and corporate names mentioned in this manual may not be reg-
istered trademarks or copyrights of their respective companies, and are
used for identication purposes only. All trademarks are the property of their
respective owners.
Every effort has been made to ensure that the contents of this manual are cor-
rect and up to date. However, the manufacturer makes no guarantee regard-
ing the accuracy of its contents, and reserves the right to make changes
without prior notice.
CAUTION:
Risk of explosion if the battery is replaced with an incorrect type. Batteries
should be recycled where possible. Disposal of used batteries must be in
accordance with local environmental regulations.

2
ZOTAC ZBOX
Table of Contents
Product Specications -------------------------------------------------------------------------- 3
Safety information -------------------------------------------------------------------------------- 4
Setting up your system ----------------------------------------------------------------------- 4
Care during use -------------------------------------------------------------------------------- 4
Welcome --------------------------------------------------------------------------------------------- 5
Package contents ------------------------------------------------------------------------------ 5
Getting to know your ZOTAC ZBOX -------------------------------------------------------- 6
Front view ---------------------------------------------------------------------------------------- 6
Rear view----------------------------------------------------------------------------------------- 7
BIOS settings of specic functions--------------------------------------------------------- 8
How to disable the ring LED indicator ---------------------------------------------------- 8
How to enable USB2.0 charge (for S3/S4/S5 status)--------------------------------- 9
How to disable CIR controller (for internal IR receiver)------------------------------- 11
Installing Hardware inside ZOTAC ZBOX ------------------------------------------------- 12
Installing a memory module ----------------------------------------------------------------- 13
Removing the memory module ------------------------------------------------------------- 14
Installing a hard disk -------------------------------------------------------------------------- 15
Setting up your ZOTAC ZBOX ---------------------------------------------------------------- 17
Positioning your ZOTAC ZBOX--------------------------------------------------------------- 19
Installing the stand----------------------------------------------------------------------------- 19
Installing your ZOTAC ZBOX to a monitor ----------------------------------------------- 19
IR receiver --------------------------------------------------------------------------------------- 20
Remote control --------------------------------------------------------------------------------- 20
Function keys ------------------------------------------------------------------------------- 20
Lithium cell installation-------------------------------------------------------------------- 21
Installing drivers and software --------------------------------------------------------------- 22
Installing an operating system -------------------------------------------------------------- 22
Installing system drivers---------------------------------------------------------------------- 22
Using your ZOTAC ZBOX----------------------------------------------------------------------- 23
Conguring wireless connection ----------------------------------------------------------- 23
Conguring wired connection --------------------------------------------------------------- 23
Using a static IP ---------------------------------------------------------------------------- 23
Using a dynamic IP (PPPoE connection) -------------------------------------------- 24
Conguring audio output via an HDMI device ------------------------------------------ 24

3
ZOTAC ZBOX
Product Specications
q Chipset
v Intel® NM70 Express
qProduct Size
v 188mm x 188mm x 51mm
qMicroprocessor support
v Intel®Core Processor (1.1 GHz, dual-core)
qOperating systems:
v Supports Windows 7 32bit/64bit and Windows 8 32bit/64bit
qSystem Memory support
v Two 204-pin SO-DIMMs DDRIII 1333/1066
v Up to 16 GB of memory
qUSB Ports
v Two USB 3.0 ports (one front panel port, and one top panel port)
v Two USB 2.0 ports on the rear panel
qOnboard Serial ATA
v SATA 6.0 Gb/s transfer rates
vSupports one 2.5-inch SATA HDD or SSD (support the device with max 9.5mm
height)
q Onboard Dual LAN
v Supports 10/100/1000 Mbps operation
vSupports IEEE 802.3
q WiFi/Bluetooth support
v Compliant with IEEE802.11n Draft 2.0 standard
vHigh speed wireless connection and enhanced wireless security
v Fully qualied Bluetooth v4.0
qOnboard Audio
v Optical SPDIF Output
v Stereo analog audio output and Microphone input
qGreen Function
v Supports ACPI (Advanced Conguration and Power Interface)
qOnboard Graphics support
vNvidia GT610
v HDMI & DVI output (VGA compatible with adapter)

4
ZOTAC ZBOX
Safety information
Your ZOTAC ZBOX is designed and tested to meet the latest standards of safety for infor-
mation technology equipment. However, to ensure your safety, it is important that you read
the following safety instructions.
Setting up your system
Read and follow all instructions in the documentation before you operate your system.
Do not use this product near water or a heat source such as a radiator.
Set up the system on a stable surface with the provided stand. Never use the system
alone without the stand.
Openings on the chassis are for ventilation. Do not block or cover these openings.
Make sure you leave plenty of space around the system for ventilation. Never insert
objects of any kind into the ventilation openings.
Use this product in environments with ambient temperatures between 0℃and 35℃.
 If you use an extension cord, please use the UL listed cord and make sure that
the total ampere rating of the devices plugged into the extension cord does not
exceed its ampere rating.
Care during use
Do not walk on the power cord or allow anything to rest on it.
Do not spill water or any other liquids on your system.
When the system is turned off, a small amount of electrical current still ows. Always
unplug all power, modem, and network cables from the power outlets before cleaning
the system.
If you encounter the following technical problems with the product, unplug the power
cord and contact a qualied service technician or your retailer.
¾The power cord or plug is damaged.
¾Liquid has been spilled into the system.
¾The system does not function properly even if you follow the operating instructions.
¾The system was dropped or the cabinet is damaged.
¾The system performance changes.

5
ZOTAC ZBOX
Welcome
Congratulations on your purchase of the ZOTAC ZBOX. The following illustration displays
the package contents of your new ZOTAC ZBOX. If any of the below items is damaged or
missed, contact your retailer.
Package contents
• 1 x ZOTAC ZBOX
• 1 x Stand
• 1 x VESA mount
• 1 x AC Adapter
• 1 x DVI-to-VGA Adapter
• 1 x Power Cord
• 2 x Antennas
• 1 x Remote Control with 2 x CR2032 batteries
• 1 x USB Extended IR Receiver for Remote Control
• 1 x Support DVD
• 1 x User Manual & Warranty Card
• 1 x Quick Start Guide

6
ZOTAC ZBOX
Getting to know your ZOTAC ZBOX
Front view
1 2 3 4 5 6 7
Refer to the diagram below to identify the components on this side of the system
1. Headphone/Audio Out jack
The stereo headphone jack (3.5mm) is used to connect the system’s audio out
signal to amplied speakers or headphones.
2. Microphone jack
The microphone jack is designed to connect the microphone used for video confer-
encing, voice narrations or simple audio recordings.
3. Memory card slot
The built-in memory card reader reads SD/SDHC/SDXC/MMC cards used in
devices like digital cameras, MP3 players, mobile phones and PDAs.
4. USB 3.0 port
The USB 3.0 port supports the SuperSpeed USB 3.0 devices and is backwards
compatible with USB 2.0/1.1 devices. Use this port for USB 3.0 devices for
maximum performance with USB 3.0 compatible devices.
5. WiFi LED
The WiFi LED blinks when data is being transfered over WiFi.
6. Hard disk LED
The hard disk LED blinks when data is being written into or read from the hard disk
drive.
7. Power switch
The power switch allows powering ON and OFF the system

7
ZOTAC ZBOX
Rear view
Refer to the diagram below to identify the components on this side of the system.
1. WiFi antenna connector
The WiFi antenna connector supports WiFi antenna module.
2. Optical (SPDIF OUT) jack
Plug an optical cable into this jack for digital audio transfer.
3. LAN ports
The eight-pin RJ-45 LAN ports support standard Ethernet cables for connection to
a local network.
4. USB 2.0 ports
The USB (Universal Serial Bus) port is compatible with USB devices such as
keyboards, mice, cameras and hard disk drives. They also support USB IR receiver
(please refer to page 20).
5. DVI port
The DVI port supports connection to analog monitors and displays.
6. HDMI port
The HDMI (High Denition Multimedia Interface) port supports a Full-HD device
such as an LCD TV or monitor to allow viewing on a larger external display.
7. Bluetooth antenna connector
The bluetooth antenna connector supports bluetooth antenna module.
8. Power input (DC19V)
The supplied power adapter converts AC power to DC power for use with this jack.
Power supplied through this jack supplies power to the PC. To prevent damage to
the PC, always use the supplied power adapter.
The power adapter may become warm to hot when in use. Do not cover the
adapter and keep it away from your body.
1 2 4 5 6 7 8 3

8
ZOTAC ZBOX
BIOS settings of specic functions
ZOTAC ZBOX has some specic functions which can be enabled or disabled in BIOS
settings, such as LED indicator, USB2.0 charge and CIR controller.
How to disable the ring LED indicator
1. Turn on the ZBOX mini-PC, then press <Delete> to enter the BIOS SETUP
UTILITY.
2. Use the arrow keys to navigate to the PowerManage menu and select
LOGO Indicator.

9
ZOTAC ZBOX
3. Press <Enter> and select Disabled.
4. Press F10 to save the conguration and exit.
How to enable USB2.0 charge (for S3/S4/S5 status)
1. In PowerManage menu, select USB2.0 S3/S4/S5 Charge Function and
press <Enter>.

10
ZOTAC ZBOX
2. Use the arrow keys to enter the item Rear / Front / Top USB2.0 S3/S4/S5
Charge, and select Enabled.
3. Press F10 to save the conguration and exit.
Note: Before charging via USB2.0 in S5 status, please make sure the Deep S5
(DeepSleep(ErP Compliant) S5 in PowerManage menu) is disabled.

11
ZOTAC ZBOX
How to disable CIR controller (for internal IR receiver)
1. Use the arrow keys to navigate to Advanced > OnBoard Device Control >
CIR Controller Conguration.
2. Enter CIR Controller and select Disabled.
Enabled: enable the internal IR receiver (default)
Disabled: disable the internal IR receiver
3. Press F10 to save the conguration and exit.

12
ZOTAC ZBOX
Installing Hardware inside ZOTAC ZBOX
Before installing hardware, please follow the instructions below to remove the cover of your
ZOTAC ZBOX.
1. Unscrew.
2. Gently remove the cover as the image below.

13
ZOTAC ZBOX
2. Gently press down on the memory module until it locks into place by the arms of the
memory slot.
Note: This ZOTAC ZBOX accomodates two DDR3 SO-DIMM memory modules. You must install at least
one module in one of the two slots.
Installing a memory module
1. Locate the SO-DIMM memory slots and insert a SO-DIMM memory module into the slot
at a 45 degree angle.
Note: When installing two SO-DIMM memory modules, please insert a module into the lower slot rst.

14
ZOTAC ZBOX
Removing the memory module
1. Locate the SO-DIMM memory slot and gently press the two arms securing the memory
module outwards, as shown in the image below, to release the memory module.
2. Remove the memory module from the slot at a 45-degree angle.

15
ZOTAC ZBOX
Installing a hard disk
1. Locate the 2.5-inch SATA hard disk and the hard disk bracket.
2. Install the hard disk to the hard disk bracket.

16
ZOTAC ZBOX
3. Insert the hard disk into the slot at a 45 degree angle and gently slide into the connector.
4. Reinstall the thumb screw.

17
ZOTAC ZBOX
Setting up your ZOTAC ZBOX
You need to connect peripherals before using your ZOTAC ZBOX.
1. Connecting a WiFi antenna module
Connect a WiFi antenna module to the WiFi antenna connector.
2. Connecting an optical S/PDIF output
Connect a digital audio device via optical S/PDIF output.
3. Connecting to a network device
Connect one end of a network cable to the LAN port on the system rear panel and
the other End to a hub or switch.
4. Connecting to USB 2.0 devices
Connect USB devices like wired/wireless keyboards (varying with areas), mouse
devices and printers to the USB ports on the system rear panel.
1
345
6
5
7
8
2

18
ZOTAC ZBOX
5. Connecting to a DVI or VGA display
Connect one end of a DVI/VGA cable to an HDTV or monitor, and the other end
to the DVI port on the system rear panel. If using a VGA connection, please use
included DVI-to-VGA adapter.
6. Connecting to an HDMI display
Connect one end of an HDMI cable to the HDMI port on the system rear panel and
the other end to a HDMI-compatible display such as an HDTV or monitor.
7. Connecting a Bluetooth antenna module
Connect a bluetooth antenna module to the bluetooth antenna connector.
8. Turning on the system
Connect the supplied AC adapter to the DC IN jack on the system rear panel and
then press the power switch on the front panel to turn on the system.
When your ZOTAC ZBOX is not in use, unplug the power adapter or switch off the
AC outlet to save on power consumption.

19
ZOTAC ZBOX
Positioning your ZOTAC ZBOX
Do not position the ZOTAC ZBOX where the ventilation holes are covered. To
guarantee proper use, leave 4 inches (10 cm) spacing in front of the ventilation
holes.
ZOTAC mini-PC system provide ample connectivities in tiny space, please choose
connectors and cables in appropriate size to avoid interference.
Installing your ZOTAC ZBOX to a monitor
You can also install your ZOTAC ZBOX to the back of a monitor. To do so:
1. Secure the VESA mount to your monitor with four screws (HNM/M4x8).
2. Place your ZOTAC ZBOX on the VESA mount noting the correct alignment and
then secure the PC to the VESA mount with a coin.
To fasten the VESA mount, your monitor must comply with VESA75 Or VESA100
standard.
Mechanical Loading Stability - Mounting of the equipment on the backside of the
monitor should be lay this equipment on a reliable surface when install. A drop or
fall could cause injury.
If the total weight of your monitor and ZOTAC ZBOX is over 7kg, the system may
be unstable.
Installing the stand
Erect your ZOTAC ZBOX with the supplied stand. To do so :
1. Locate the screw hole on the bottom of the ZOTAC ZBOX.
2. Align the stand screw to the PC screw hole and then secure the Stand to the PC
with a coin.
Do not place your ZOTAC ZBOX on the desktop without the stand.



