Zte SD6200 Original instructions

1
SD6200
WebUI User Manual and Safety
Information

1
About This Manual
Thank you for choosing this mobile device. To keep your device in its best condition, please read
this manual and keep it for future reference.
Notice
This manual has been designed with the utmost care to ensure the accuracy of its content.
However, all statements, information and recommendations contained therein do not constitute a
warranty of any kind, either expressed or implied. Please refer to For Your Safety to be sure to
use your phone properly and safely.
Disclaimer
Images and screenshots used in this manual may differ from the actual product. Content in this
manual may differ from the actual product or software.
Trademarks
Other trademarks and trade names are the property of their respective owners.
Version No.: R1.0
Edition Time: June 22 2018

2
Getting Started............................................................5
Know Your OBD2 (On-Board Diagnostic) Device............... 5
Status LED Indicator .......................................................... 6
Reset the OBD2 Device..................................................... 7
Restart the OBD2 Device................................................... 7
Installing the micro-SIM Card............................................. 8
Installing your OB2 Device ......................................10
Manage Your OBD2 Device and Settings ...............12
Connect Devices to Your OBD2 Device’s Wi-Fi ............... 12
Connect a wireless device manually ................................ 12
Use Your OBD2 Device.............................................13
4G Mobile Hotspot Configuration Page............................ 13
Security Credentials.................................................14

3
Manage Wi-Fi.............................................................14
View Connected Devices .................................................14
Set Maximum Number of Connected Devices..................15
Add / removed Devices ....................................................17
Security......................................................................18
Change Wi-Fi Network Name and Password. ..................18
Change 4G Mobile Hotspot Configuration Page Access
Settings ............................................................................19
Change Wi-Fi Security Types...........................................20
Configure Data Network Options......................................21
Advanced Settings....................................................23
Manage Wi-Fi...................................................................23
Change Advanced Settings......................................24
View WAN Information .....................................................24
Enable Port Mapping........................................................24
Enable MAC/ IP/Port Filtering ..........................................24
Configure APN details ......................................................25

4
Troubleshooting .......................................................27
Compatible vehicles.................................................28
Working Voltage........................................................28
Specifications ...........................................................29
Regulatory and Safety Information.........................30
Warranty ....................................................................33

5
Getting Started
Know Your OBD2 (On-Board Diagnostic) Device
Your OBD2 device enables you to create a Wi-Fi network in your vehicle. You can use that Wi-Fi
network to connect your smartphone and other Wi-Fi capable devices to your network provider’s
mobile broadband network and connect to the Internet.
Device reset hole
micro-SIM card slot
Restart key
LED 1
LED 2
OBD2
Interface

6
Status LED Indicator
LED INDICATOR LED STATUS

7
Reset the OBD2 Device
You can reset the OBD2 device to the factory setting on the OBD2 device or the 4G Mobile
Hotspot configuration page. (This is useful if you have lost your Admin Login for the 4G Mobile
Hotspot configuration page.)
NOTE:
If you reset the modem to factory settings, all your customizations will be lost. If you want to
keep them, save them before doing the reset, and then restore them afterward. Note: When you
reset the OBD2 device, any currently connected devices will lose access and will have to be
reconnected after the OBD2 device restarts.
On the OBD2 device:
Insert a pin into Reset hole and hold for about 3 seconds until the LED1 indicator turns red.
After the device has reset, reconnect Wi-Fi devices.
On the 4G Mobile Hotspot configuration page:
•Log in as Administrator.
•Select Settings > Device Settings.
•Select Reset.
Restart the OBD2 Device
You can restart the OBD2 device by pressing the restart key.

8
Installing the micro-SIM Card.
1. Insert the tip of the tray eject tool to eject the SIM card tray.
2. Place the micro-SIM card on the tray with the gold-colored contacts facing down and slide
the tray back into place.

9
WARNING!
To avoid damage to the device, do not use any non-standard micro-SIM card cut from a card. You
can get a standard micro-SIM card from your service provider.

10
Installing your OB2 Device
•Make sure your vehicle is parked outside in a safe location and the engine is turned off.
•Connect your OBD2 device into the OBD connector port (or into the extension cable if it is
required –not included). Ensure that your OBD2 device is connected in the correct direction.
NOTE:
Gently insert your OBD2 device as to avoid damage to the device.
•OBD interface connect with OBD connector on your vehicle to power on your OBD2 device.
The OBD (On-Board Diagnostics) connector is usually located on or under the dash, on the
driver’s side. Other possible locations are at the center console area or inside the glove
compartment.

11
•Start your vehicle’s engine and let it run for at least 30 seconds.
•Once powered up, your OBD2 device automatically searches for and connects to your
network provider’s mobile broadband network.
•Connect your smartphone or other WPS-enabled devices to your network.
•Use your normal Wi-Fi application on the client to search for the available wireless
network.
•Select the Wi-Fi network name.
•Input the Wi-Fi network password, as it displays on the label on your OBD2 device.
•Launch your browser to surf the Internet.

12
Manage Your OBD2 Device and Settings
You can use the 4G Mobile Hotspot configuration page to manage your OBD2 device and change
settings.
NOTE:
To personalize the OBD2 device and change settings, use a Wi-Fi enabled device to connect to
the OBD2 device and then use a browser to display the 4G Mobile Hotspot configuration page
(http://192.168.0.1).
Log in as Administrator to make changes. (The default Admin Login is: admin).
Connect Devices to Your OBD2 Device’s Wi-Fi
You can connect up to 10 wireless devices such as smartphones, laptops, tablets, digitalcameras,
printers, gaming consoles, and digital picture frames to your OBD2 device’s Wi-Fi network. (See
Set maximum number of connected devices for instructions on setting connections for the Wi-Fi
network.)
You can connect a wireless device to your Wi-Fi network by typing the Wi-Fi password.
Connect a wireless device manually
To connect a wireless device to your OBD2 device’s Wi-Fi network, see Connect to the Internet.

13
Use Your OBD2 Device
This chapter describes the main features of the web interfaces for managing your OBD2 device.
4G Mobile Hotspot Configuration Page
You must be logged in as Administrator to change settings and view detailed information.
• Default homepage URL — (http://192.168.0.1)
• Default Administrator Login — admin
To log in as Administrator:
1. On the 4G Mobile Hotspot configuration page, place your cursor in the Password field and
type admin (the default login).
2. Select Login.

14
Security Credentials
The OBD2 device uses two passwords:
•Wi-Fi password —used to authenticate wireless devices to your mobile hotspot network.
It is unique to your mobile hotspot and can be found printed on a label on the mobile
hotspot. If you want to change the Wi-Fi password, see Change Wi-Fi Network Name and
Password on page 12.
•Admin Login —usedto log into the4G Mobile Hotspot configuration page as Administrator.
You must be logged in as Administrator to use certain features and to make changes to
your OBD2 device settings. The default Admin Login is admin. The Admin Login can be
changed to 4–32 characters.
You can change these passwords on the 4G Mobile Hotspot configuration page
(http://192.168.0.1).
Manage Wi-Fi
View Connected Devices
You can view a list of devices connected to your OBD2 device on the 4G Mobile Hotspot
configuration page.
•Log in as Administrator.
•Select Home. A list of devices Connected to the Wi-Fi network appears in the Connected
Devices section. You can view the IP and MAC addresses of the devices.

15
Set Maximum Number of Connected Devices
You can connect up to 10 wireless devices to your OBD2 device. You can customize the
number of devices from the 4G Mobile Hotspot configuration page.
•Log in as Administrator.
•Select Settings.
•In the SSID section, select drop-down box beside Maximum Number of connections to
set the number of connections available for the Wi-Fi network.

16
•Select Apply.

17
Add / removed Devices
You can prevent other device from connecting to the OBD2 device, only the MAC address listed
in the Allowed Devices Information section can access your OBD2 device. You can add /
remove a device from the 4G Mobile Hotspot configuration page.
To add a device:
•Log in as Administrator.
•Select Settings > Wi-Fi Settings.
•Set Allowed Devices Switch to On and select Apply.
•Enter the Nickname and MAC Address.
•Select Apply.

18
To remove a device:
•Log in as Administrator.
•Select Settings > Wi-Fi Settings.
Select Remove next to the device in the Add / removed Devices section.
Security
Change Wi-Fi Network Name and Password.
You can customize the network name and password for the Wi-Fi network from the 4G Mobile
Hotspot configuration page.
•Log in as Administrator.
•Select Settings > Wi-Fi Settings.
•Change the Wi-Fi network name and / or password in the SSID section.
•Select Apply