Zte ZXV10 W300 Operating and maintenance instructions
ZXV10 W300
Wireless ADSL/LAN Router
Quick Installation Manual
ZTE CORPORATION
1
ZXV10 W300 Wireless ADSL Router
Quick Installation Manual
Manual version 20060810-R1.0
Product version
Copyright © 2005 ZTE CORPORATION
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated,
annotated or duplicated, in any form or by any means without the prior
written permission of ZTE CORPORATION.
* * * *
ZTE CORPORATION
ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P.
R. China
Website: http://support.zte.com.cn
Post code: 518057
Customer Support Center: (86) 755 26771900 800-9830-9830
Fax: (86) 755 26772236
* * * *
S.N.: ×××××××
2
Contents
1 PRODUCT INTRODUCTION ...............................................................................5
1.1 PRODUCT FEATURES .............................................................................................5
1.2 PACKING LIST .......................................................................................................6
1.3 SYSTEM REQUIREMENT.........................................................................................7
2 INTRODUCTION TO THE HARDWARE ...........................................................8
2.1 INDICATORS ..........................................................................................................8
2.2 PORTS AND BUTTONS............................................................................................9
3 QUICK INSTALLATION .....................................................................................11
3.1 HARDWARE CONNECTIONS .................................................................................11
3.2 FACTORY DEFAULTS............................................................................................13
3.3 COMPUTER SETUP...............................................................................................14
3.3.1 Checking Computer Settings ......................................................................14
3.3.2 Configuring TCP/IP ...................................................................................14
4 WIZARD.................................................................................................................16
4.1 LOGGING ON TO THE ZXV10 W300 DEVICE........................................................16
4.2 SETTING ATM PVC............................................................................................17
4.3 CONNECTIONS ....................................................................................................18
4.4 SETTING CONFIGURATIONS .................................................................................19
4.5 CONFIGURATION INFORMATION...........................................................................20
4.6 CONFIGURATION COMPLETED .............................................................................20
4.7 OTHER COMMON CONFIGURATIONS ....................................................................21
4.7.1 Creating New WAN Connections................................................................21
4.7.2 UPnP..........................................................................................................26
4.7.3 DMZ ...........................................................................................................27
3
4.7.4 Dynamic DNS.............................................................................................28
4.7.5 TR069.........................................................................................................29
5 TECHNICAL SPECIFICATIONS .......................................................................32
5.1 HARDWARE SPECIFICATIONS ...............................................................................32
5.2 SOFTWARE SPECIFICATIONS ................................................................................33
6 QS AND AS.............................................................................................................35
4
1 Product Introduction
Welcome you to use the ZXV10 W300 Wireless ADSL/LAN Router.
ZXV10 W300 series products are home user oriented wireless broadband
router integrating ADSL, AP and LAN Switch. The ZXV10 W300 router
acts as the center of a home network and lets all of the devices in a home
network share the same Internet connection, providing the users with
Triple play services integrating wired or wireless communications, voice
and video. It supports the classification of message contents based on
service traffic and priority tagging for different service requirements,
provides superior QoS based on ATM and IP, and meets the requirement
of access bandwidth for different services. It provides secure wireless
encryption and powerful firewall to prevent unauthorized users access. In
addition, it uses the TR069 system providing unified management to
meet different requirements of carrier-level and user-level network
management. Besides all of the previous SNMP functions, the TR069
system is added with terminal device and user management functions to
provide the overall remote network management capability.
1.1 Product Features
Provide ADSL/ADSL2/ADSL2+/LAN high-speed Internet
access.
Support ITU G.992.1, G.992.2, G.992.3, G.992.5 and ANSI
T1.413 Issue 2.
Provide four 10/100Base-T Ethernet interfaces supporting
automatic identification of crossover cable and
straight-through cable.
Provide one IEEE 802.11g/b wireless interface
Provide wireless data security using WEP-64/128/256,
WPA/WPA2 and MAC address filtering.
Provide functional features including subscriber isolation,
ESSID hiding and multi-ESSID
Support Bridge and Router modes
5
ZXV10 W300 Quick Installation Manual
Support eight PVC connections and auto-negotiation
Support PPPoE, PPPoA, Static, DHCP, Bridge and CLIP
connections.
Support NAT, IP filtering and firewall functions.
Support network configuration using DHCP
Support UPnP, SNTP, DMZ, IGMP Snooping, IGMP Proxy
and DNS Proxy.
Support ATM QoS and IP QoS functions
Support configuration via web and SNMP management
High reliability, ease of use and low power consumption
High compatibility and interoperability with various
office-end DSLAMs
Note:
Corresponding ISP services are required for the above functions.
1.2 Packing List
The package of the W300 product should contain the following
components:
W300 ADSL/LAN Router 1
External splitter1
Power supply adapter1
Telephone wires 2
Straight-through cables1
Warrantycard 1
Quality certificate1
ZXV10 W300 Wireless ADSL/LAN Router Quick
Installation Manual1
6
Chapter 1 Product Introduction
If any of the above components is missing or damaged, please contact
your dealer.In case of replacement, please keep the package and existing
components of the product well.
1.3 System Requirement
Before using the ZXV10 W300 product, please ensure the following
system requirements:
You have subscribed the ADSL/LAN service. Your Internet
Service Provider must provide you with at least one legal IP
address (allocated dynamically via dial-up or statically)
One or more PCs with 10/100 M Ethernet Network Interface
Card (NIC)
For wireless access, an external or built-in 802.11g/b
wireless NIC is required.
To set up the system via web, a browser is required, e.g.
Internet Explorer V5.0 or later, or Netscape V4.7 or later.
7
2 Introduction to the Hardware
2.1 Indicators
There area eight indicators on the front panel of the ZXV10 W300. These
indicators indicate the service running status of the ZXV10 W300. The
indicates are described in the table below.
No.Indicators Identificatio
nColorDescription
1Power
supplyRed
Steady ON: Indicates the
power supply is
connected and turned on.
OFF: Indicates the
power supply is
disconnected or a failure.
2InternetGreen
Steady ON: The device
is connected to the
Internet successfully via
built-in dial-up.
3RunningGreen
Flashing: Indicates the
device operates
normally. OFF: Indicates
a device operation
8
Chapter 2 Introduction to the Hardware
Identificatio
No.Indicators ColorDescription
n
failure.
4WLANGreen
Steady ON: Indicates
Wi-Fi is switched on.
Flashing: The indicator
flashes according to the
network traffic flow.
OFF; Indicates Wi-Fi is
switched off.
5LAN
Green
Steady ON: Indicates the
device has been
connected to the LAN.
Flashing: The indicator
flashes according to the
network traffic flow.
OFF: Indicates the
device has not been
connected to the LAN
6
ADSL
/WAN
link
Green
Steady ON: Indicates an
ADSL/WAN connection
is established and
activated. Slow flashing:
Indicates a connection is
being established on the
ADLS line or flashes
according to the network
traffic flow. OFF:
Indicates no
ADSL/WAN connection
can be established.
2.2 Ports and Buttons
9
ZXV10 W300 Quick Installation Manual
There are nine ports and buttons on the side of the ZXV10 W300 device.
Ports and buttons are described in the table below.
No.Port
identificationDescription
1DSLConnected to the ADSL line or splitter via RJ-11
telephone wire
2WA N
Connected to the ADSL line via RJ-11, or
connected WAN via RJ-45
1 and 2 is alternative. When use 1 as ADSL router,
the connector 2 will not be provided. And when use
2 as ADSL/LAN router, 1 will not be provided.
3LAN1~ LAN4 Connected to the PC NIC via RJ-45 cable
4Wi-FiWLAN radio frequency ON/OFF switch
5Reset
The device is power on. Holding on the button for
more than 10 seconds will reset the current settings
to the factory default settings, and the system will
then restart automatically.
6On/OffPower switch
7PowerConnected to the associated power adaptor
8Antenna Antenna
10
3 Quick Installation
It is assumed that you have signed up for the ADSL service from the
Service Provider. In addition, this chapter contains the basic product
configuration only, which is applicable to the network environment of
general subscribers or enterprise users.
3.1 Hardware Connections
The following diagram illustrates the recommended connections and
installation via ADSL connector.
The following diagram illustrates the recommended connections and
installation via WAN connector.
11
ZXV10 W300 Quick Installation Manual
Note:
Phone sets connected in parallel before the splitter will cause many
problems, e.g. the ZXV10 W300 device cannot be connected to
office-end devices; networks cannot be accessed or the network access
speed will be slow. To connect phone sets before the splitter, a microfilter
should be connected in serial in front of the phone sets (In general, only
one microfilter can be connected in front of the splitter to reduce
interference).
1. Installation position
The ZXV10 W300 device can be placed on a plane surface like
desktop, or installed on the wall. It is recommended to place the
device on the center of the network to be established and keep it
far away from possible interference sources, e.g. metal wall and
microwave oven, for the highest efficiency. It is also
recommended to place it on a relatively higher position so that it
covers all of the physical space.
Note:
In the case it is installed on the wall, you must secure the device to
prevent it from being damaged due to fall-off. Enough space should be
reserved around of the device for normal heat dissipation.
2.If ISP is ADSL, then connect the DSL or WAN port of the device to
the MODEM port of the splitter using a telephone wire. Connect the
phone set to the PHONE port of the splitter using another telephone
wire, and then connect the subscriber telephone line providing the
ADSL service to the LINE port of the splitter, as shown in the
hardware connection diagram.
The splitter has three ports, including:
LINE: Port connected to the subscriber telephone line
providing the ADSL service
12
Chapter 3 Quick Installation
MODEM: Port connected to the DSL port of the
ZXV10 W300 device
PHONE: Port connected to a phone set
3. If ISP is LAN, then connect the WAN port of the device to ISP’s
Ethernet line.
4.Connect the LAN port of the device to a PC with a NIC using an
RJ45 cable.
5.Connect the power adapter to the Power port of the device, and plug
the adapter to the AC power socket. The device will be powered on
and operate after you pushing the power switch button.
Warning
Please use the power adaptor we provided. Other power adaptor may
make the device unable to work normally or even damage it.
3.2 Factory Defaults
Factory defaults of the ZXV10 W300 device are as follows:
IP address: 192.168.1.1; Subnet mask: 255.255.255.0
Use DHCP server by default. The IP address can be obtained
from the device via DHCP.
Line coding: AUTO
(T1.413/G.DMT/G.LITE/ADSL2/ADSL2+ auto-sensing)
WLAN default ESSID: BAVO
Username and password for logging on to the device: admin,
admin.
Note:
In the cases the device does not work due to configuration errors, or you
forget the password, just insert a needle into the Reset hole of the device
13
ZXV10 W300 Quick Installation Manual
and hold down the button for more than 10 seconds when the device is
powered on. This will restore the current settings to the factory defaults
and then the system will restart automatically.
3.3 Computer Setup
3.3.1 Checking Computer Settings
If your computer uses a proxy server to access the Internet, first you must
disable the proxy service. You must also close the VPN software and the
firewall running on your computer. In the Microsoft Internet Explorer,
check the proxy service settings as follows:
1.In the browser window, select Tools > Internet Options.
2.Click the Connections tab and then the LAN Settings button.
3.Make sure the Use a proxy server for your LAN box is unchecked.
If it is checked, uncheck it and click OK.
3.3.2 Configuring TCP/IP
If your computer uses Windows 95/98/ME/2000/XP, set up your
computer using one of the following two methods of which the first one
is recommended. The following examples use Windows XP as the
operating system. The setup of computers using other operating systems
is similar.
1. The PC can obtain an address from the device via DHCP.
1)From the Windows taskbar, select Start > Control
Panel.
2)Double-click the Network Connection icon.
3)From the right-button menu, select Local Area
Connection > Properties. Select Internet Protocol
(TCP/IP) > Properties.
4)From the Internet Protocol (TCP/IP) Properties
dialog box:
Ensure that Obtain IP address Automatically is checked.
5)Ensure that Obtain DNS server address
14
Chapter 3 Quick Installation
automatically is checked.
6)Click OK twice to confirm and save your settings.
2.Configure the PC to use a static address:
1)From the Windows taskbar, select Start > Control
Panel.
2)Double-click the Network Connection icon.
3)From the right-button menu, select Local Area
Connection > Properties. Select Internet Protocol
(TCP/IP) > Properties.
4)In the Internet Protocol (TCP/IP) Properties
dialog box, click Use the following IP address to specify
the local computer's IP address to the same network
segment as the LAN port address of the device, i.e.
192.168.1.x (in which the "x" is a decimal integer between
2~254). For example, 192.168.1.2, subnet mask
255.255.255.0. The Default Gateway is set to 192.168.1.1.
5)Configure Use the following DNS server
addresses. To set the DNS server IP addresses, please
contact your local Service Provider, or set it to 192.168.1.1.
6)Click OK twice to confirm and save your settings.
3.After completing the above configuration:
1)If the device is set to the bridging mode, you can
access the Internet using the service (e.g. PPPoE dial-up)
provided by the your service provider.
2)If the device is set to the routing mode, you can
access the Internet directly when it has been connected to
the office-end device successfully.
3)To check the ZXV10 W300 device settings, visit
http://192.168.1.1 via a browser and log on to the device
using admin as both the username and the password.
15
4 Wizard
You need relevant technical knowledge and experience for configuring
the ZXV10 W300 device. To simplify your operations, it is
recommended to use the wizard for quick configuration. A little
configuration will allow you to establish the connection for basic use.
However, to use advanced functions of the device, you need to configure
other options.
Make sure the following issues before configuration:
The computer has been connected to the Ethernet port of the
device using a network cable.
TCP/IP is set properly on your computer.
All the running firewall and VPN software have been closed.
The proxy server setting of the browser you use, e.g. IE, has
been disabled.
Your service provider has provided you with required data. You
can contact your service provide for help.
Notes
ġ
ZXV10 W300 wireless ADSL/LAN router can be used as
ADSL router or LAN router. So the software include ADSL and
LAN setup interface. When used as LAN router, users should not
set the VPI and VCI.
4.1 Logging on to the ZXV10 W300 Device
The ZXV10 W300 device provides a web-based configuration tool that
allows you to configure and manage the device via a web browser. Open
IE. Type in http://192.168.1.1 into the address bar and then press the
Enter key. A login page as shown below appears.
16
Chapter 4 Wizard
Select the language for web configuration. Enter your Username and
Password (which are admin and admin by default), and then click the
Login button to enter the configuration main page.
4.2 Setting ATM PVC
Click the Wizard button on the main page to enter the quick
configuration wizard which allows you to configure the DSL Modem
quickly.
In the first step, the page displays the PVC default value of the WAN
interface. The VPI/VCI value depends on the operational environment.
Please contact your service provider for the data. After completing the
setting, click Next on the page.
17
ZXV10 W300 Quick Installation Manual
4.3 Connections
You can select one of the ADSL access modes, including PPPoE, PPPoA,
Bridge, DHCP, Static Bridged, Static Routed and CLIP, and then
configure data encapsulation. Please contact your service provider for the
settings of connection and encapsulation. After completing the setting,
click Next on the page.
18
Chapter 4 Wizard
4.4 Setting Configurations
The configuration page you enter may be different depending on the type
of connection you selected. The configuration sequences in the cases of
the seven types of connections are as follows, respectively:
PPPoA and PPPoE: ATM PVC Setting > Connection Type
> PPP Username and Password > Configuration
Information > configuration completed.
DHCP and Bridge: ATM PVC Setting > Connection Type
> Configuration Information > configuration completed.
Static Bridged and Static Routed: ATM PVC Setting >
Connection Type > WAN Setting > Configuration
Information > configuration completed.
CLIP: ATM PVC Setting > Connection Type > CLIP
Setting > Configuration Information > configuration
completed.
The following procedure takes the most common PPPoE as an example
to illustrate how to set the PPP user account and password. Please contact
19
ZXV10 W300 Quick Installation Manual
your service provider for the specific parameters. After completing the
setting, click Next on the page.
4.5 Configuration Information
The configuration information page may be different depending on the
connection type you selected. You can check if the settings are correct.
To modify settings, click the Back button to return to the previous step.
Clicking the Submit button will allow all the settings take effect.
4.6 Configuration Completed
After clicking the Submit button, the device will prompt it is submitting
the data and checking the connection status. If the connection fails, check
the failure cause according to the prompt message. To modify or check
the entered parameters, click the Back button. To exit the wizard, click
the Back to Main Menu button. To view the latest connection status,
click the Update Status button.
20
Other manuals for ZXV10 W300
4
Table of contents
Other Zte Wireless Router manuals
Zte
Zte IDU User manual
Zte
Zte OPTUS MF920V User manual
Zte
Zte Pocket WiFi 5G A101ZT User manual
Zte
Zte MF253M User manual
Zte
Zte MF970 User manual
Zte
Zte ZXHN H268A User manual
Zte
Zte AT&T Velocity MF923 User manual
Zte
Zte MF65 User manual
Zte
Zte 4G LTERouter with Voice User manual
Zte
Zte Vodafone R209-Z User manual
