ZTOZZ HEIMA User manual
x21/4"x 13/16"x35/16" x 3 /"
x10
x8
x5
1/4" x 2 /"
x2
x2
x2
x5
x5 x4
x2
1/4" x 1 /"3/16" x 1 /"
1/4" x 2 /"5/16" x 3 /"
5/16"5/16"
1/4"1/4"
*you will need a Phillips-head
screwdriver and open-end
wrench (not included)
x4
2" x 1"
legs
x3
1/4" x 2"
hex bolts
hex bolts bolts
bolts bolts
bolts
metal washers metal washers hex nuts hex nuts
side mounting
brackets
self-tapping screws stud bolts
open-end wrench
Phillips-head screwdriver
x1
x1 x3
x1
x1
x1
x1
x2
armrest 2
roll-out sleeper
armrest 1
throw pillows sleeper cushion
stopper rails set
backrest 1chaise
backrest 2
Before starting the assembly, please select
the chaise placement – it can be installed
either on the left or the right side.
Lay armrest 1 () at onto the oor with pre-drilled holes facing upward and attach 1 x stopper rail set ()
with 2 x bolts () and 2 x metal washers () using the open-end wrench (). Then attach 2 x stud bolts ()
to the pre-drilled holes in the middle of the armrest 1 (as shown in the illustration, do not fully tighten).
Attach 1 x stopper rail set () onto the chaise () with
2 x bolts () and secure it with 2 x metal washers ()
and 2 x hex nuts () using the open-end wrench (),
depending on the chosen chaise placement.
Attach backrest 1 () onto the chaise () and screw
in the 3 x hex bolts () with 3 x metal washers ().
Flip the armrest 1 () and armrest 2 () upside down and screw in the 2 x legs ()
with 2 x self-tapping screws () per armrest using the Phillips-head screwdriver ().
Attach the 2 x side mounting brackets () onto the chaise () with
1 x bolt () per bracket using the Phillips-head screwdriver ().
Connect the sleeper cushion () and the
backrest 2 () to each other with 3 x bolts ()
and secure it with 3 x metal washers () and
3 x hex nuts () using the open-end wrench ().
Flip the assembly so that the backrest
is facing downward as pictured.
Flip the chaise assembly so that the backrest is facing downward
as pictured, open up the chaise and support it with throw pillows.
Connect the sleeper cushion assembly to the chaise using the side
mounting brackets.
Secure the mounting plates with 2 x bolts () and 3 x hex nuts ()
using the open-end wrench (). Attach screws () to the assembly
using the Phillips-head screwdriver ().
Attach the armrest 1 () , together with the stopper rail, onto the assembly. Make sure that the hook part of the stopper
rail of the armrest is facing upward. Connect the sleepper cushion part to armrest with 2 x stud bolts () already screwed
in the armrest and secure it with 2 x metal washers () and 2 x hex nuts () using the open-end wrench (). Then connect
the backrest part to the armrest with 2 x self-tapping screws () using the Phillips-head screwdriver ().
Attach the armrest 2 () to the chaise using 3 x bolts ()
along with 3 x washers () and the open-end wrench ().
Flip the sofa into
a regular position.
Roll the sleeper () into the assembly and
gently lift it up to secure it to the stopper
rails, you will hear a distinct click sound.
Put 3 x throw pillows () on the sofa and...
Other manuals for HEIMA
2
Other ZTOZZ Indoor Furnishing manuals
Popular Indoor Furnishing manuals by other brands
American Standard
American Standard Colony 2388.012 Specification sheet
Forte
Forte OSTT011 Assembling Instruction
Argos
Argos 482/0688D instruction manual
Southern Enterprises
Southern Enterprises WS476400TX Assembly instructions
Teknion
Teknion hiSpace Basic Height-Adjustable Extended Corner Complete Table... Installation guides
AKANTE
AKANTE ARTEMIS CT143 Assembly instructions
Wildwood
Wildwood BASIC TV LIFT CABINET Setup instructions
Furniture Values International
Furniture Values International aspenhome I262-360WD Assembly instructions
The Land of Nod
The Land of Nod If I Had A Hammer workbench Assembly instructions
KEUCO
KEUCO Royal Modular 2.0 800421DDEG0 00 Series Instructions for use
ROL ERGO
ROL ERGO EPI Series user manual
GFW
GFW NEWARK TV BED Assembly instructions
