Zurik EMLV User manual

DCAC
INTRODUCTION
The Zurik® EMLV Dimmable Driver is the most versatile and efficient dimmable electronic driver for single color output LED strips. This driver has
a high power factor of 0.99, a universal input and perfect compatibility with a wide range of dimmers for flicker free lighting. Its high power
efficiency, wide voltage input, and quiet operation make the EMLV the professional’s choice when it comes to flawless dimming.
SAFETY AND WARNINGS
Install in accordance with the National Electric Code (NEC) Article 450, and local regulations.
This product should be installed and serviced by a qualified electrician.
Install in a well ventilated area free from explosive gases and vapors.
Do not reverse the line voltage polarity upon installation. This will damage the driver.
Risk of electric shock: When used outdoors, install only on a circuit protected by a Class A GFCI.
Risk of fire: Special rated wire required for installations inside walls and building structures.
Consult a qualified electrician. Do not install in wet locations. Install only in dry or damp locations.
Only use with compatible dimmable LED fixtures.
Dimmer switches have minimum load requirements. Review the specifications of the compatible dimmer.
Modifying or disassembling this product beyond these instructions will void the product warranty.
•
•
•
•
•
•
•
•
•
•
ZURIK®EMLV 12V & 24V 200W LED DRIVER
Low Voltage LED Driver
DRIVER
Output Power Wires
Addional Features
(L) Live Channel
(N) Neutral Channel
( ) Ground Channel Input Power Wire
Negative Channel (-)
Positive Channel (+)
•Constant voltage output
•Easy installation
•Cooling by free air convection
•Compatible with most forward phase, magnetic low voltage,
reverse phase, and electronic low voltage dimmers
•Flicker-free dimming
•Suitable for LED lighting and sign applications among other uses
•Has 2 Output Power Wires with split output
•Comes with junction box: H: 16” (407mm) W: 3 3/8“ (86mm)
D: 2 5/16” (59mm)
V.2019.08.29
ZRK-EMLV2-200W-XXDC
1page
support@FlexfireLEDs.com 925-273-9080 opt 2
ZURIK®EMLV LED Driver 200W
User Guide

Details
Notes
•All parameters if not specially mentioned are measured at 120VAC input, rated load and ambient temperature of 25°C.
•To extend the life of the driver keep the load below 90%.
•Load on the driver should be within 10%-100%.
•Loading on the AC dimmer should not be below 40% in order to extend the life of the dimmer.
ZRK-EMLV2-200W-XXDC-J
IP66 (indoor and outdoor)
110 - 277 VAC
12VDC or 24VDC
12V: 16.66A 24V: 8.3A
200W (100W per Output Power Wire)
47 ~ 63Hz
0.98 (fully loaded)
12V: 86% 24V: 86%
2.3A @ 110VAC
<0.50mA
Shuts down output voltage, recovers
after faulty condition is removed
≤120%
212°F ± 18°F (100°C ± 10°C) Shuts
down output voltage, recovers after
faulty condition is removed
-40°F ~ 140°F (-40°C ~ 60°C)
SKU:
Ingress Protecon:
Input Voltage:
Output Voltage:
Rated Current:
Rated Power:
Frequency Range:
Power Factor:
Efficiency (Typ.):
AC Current (Max.):
Leakage Current:
Short Circuit:
Overload Protecon:
Overheat Protecon:
Working Temp:
20 ~ 90%RH. Non condensing
-40°F ~ 176°F (-40°C ~ 80°C),
10 ~ 95%RH
±0.03% /°C [32°F ~ 122°F (0 ~ 50°C)]
10 ~ 500Hz, 2G 10min./ 1 cycle, period
for 60min. Each along X,Y,Z axes
UL (E500166), conforms to UL8750,
certified to CSA STD.C22.2 No. 250.13
I/P-O/P:1880VAC
I/P-O/P:100MΩ/500VDC/25°C/70%RH
FCC Part 15B
4.91lb (2.23kg) with junction box /
3.30lb (1.5kg) without junction box
H: 10 1/8” (256mm) W: 3 1/8“ (78mm)
D: 1 7/8” (47mm)
400Hz
7 years
Working Humidity:
Storage Temp. and
Humidity:
Temp. Coefficient:
Vibraon:
Cerficaons:
Withstand Voltage:
Isolaon Resistance:
EMC Emission:
Weight:
Dimensions:
PWM Frequency:
Warranty:
V.2019.08.29
ZRK-EMLV2-200W-XXDC
2page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W

-40
20
40
60
80
100
-20 0-10 -20 30
Ambient Temperature (°C)
Load (%)
40 50 60 70
Single Color LED strip
Small flat-head screwdriver (4mm) Wire strippers or scissors
AC dimmer (optional)EMLV Driver Wire connectors
(terminal block, electrical
tape, crimp connector, etc)
2-wire stranded low
voltage wire
DCAC
To extend the power supply’s life, refer to the Derating Curve above and derate according to the ambient temperature
DERATING CURVE
YOU’LL NEED
V.2019.08.29
ZRK-EMLV2-200W-XXDC
3page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W

Knockout Holes
12”
12”
12” 12”
AC
120V AC Magnetic Low
Voltage Dimmer Switch
120V AC
Power
Positive (+)
Negative (-)
Positive (+)
Negative (-)
or
It can be mounted in any orientation, the chosen location must be able
to support the weight of the power supply with 12” of clearance for
proper ventilation. Never mount it next to objects radiating heat.
Remove wiring knockouts as needed and install 3/8” romex connectors
or bushings to reduce strain on wires. One set of knockout holes is
reserved for input voltage while the second set is reserved for output
voltage.
Connect the AC line ground (G) to the green wire from the Power Input
Wire. Do the same with the AC neutral wire to the white wire on the
driver and the AC live wire to the black wire. you can secure these
connections with a terminal block.
Look at your LED strips carefully and identify the positive (+) and
negative (-) channels.
When using a 3-pole dimmer as a single pole make sure to cap the
additional line and connect the rest of the wiring as recommended by
the dimmer instructions. Find our list of compatible dimmers below.
Connect the driver’s Output Power negative (-) wire to the - channel on
the LED strip. Connect the positive (+) wire to the + channel.
Always pre-test your LED setup prior to permanent installation. This will ensure all components work correctly. Be sure to check the wattage pull
of the LED strip you’ve purchased so the driver isn’t overloaded (Max. 108W). Turn off the main AC breaker for the line you’ll be using before install-
ing your EMLV driver. If you experience any issues at all with your test set up, please be sure to contact us at After Sales Support.
INSTALLATION
1. 2.
3. 4.
5. 6.
Mounng The Juncon Box (oponal) Using The Knockout Holes (oponal)
Using A Dimmer
Connect Outbound LED WiresIdenfy The Channels On The Strip
Connect Power Wires
V.2019.08.29
ZRK-EMLV2-200W-XXDC
4page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W

DC
DCAC
Turn the main breaker for the AC line back on to power your non-dim-
mable power supplies. The LED strip should turn on.
LUTRON COMPATIBLE DIMMERS
Forward
Phase
or Reverse
Phase
Dimming
Range
Input
Voltage
Model Number
(Dimmer)
Model Waage
DVCL-153PR-WH 100-130V 0-100%Diva Forward Phase 150W
DVWCL-153PH-LA 100-130V 0-100%Diva Forward Phase
150W
MACL-153MH-LA 100-130V 20-100%Maestro Forward Phase
150W
DV-600PR-WH 100-130V 0-100%Diva Forward Phase
600W
MRF2-6ND-120-AL 100-130V 0-100%Maestro Forward Phase
600W
MRF2-6CL-GR 100-130V 15-100%Maestro Forward Phase
150W
MSCELV-600M 100-130V 0-100%Maestro Reverse Phase
600W
MRF2-6ELV-120 100-130V 0-100%Maestro Reverse Phase
600W
MIR-600M 100-130V 2-100%Maestro IR Remote Ctrl Forward Phase
600W
NTF-10-277 277V1000W 13-100%Nova T Forward Phase
TGCL-153PR-WH 100-130V 0-100%Ariadni / Toggler Forward Phase 150W
TGCL-153PH-WH 100-130V 0-100%Ariadni / Toggler Forward Phase
150W
TG-600PR-WH 100-130V 0-100%Ariadni / Toggler Forward Phase
600W
TG-10PR-WH 100-130V 0-100%Ariadni / Toggler Forward Phase
1000W
PD-6WCL 100-130V 20-100%Caseta Forward Phase
150W
PD-5NE-WH 100-130V 18-100%Caseta Forward Phase
250W
Caseta PD-10NXD-WH 100-130V800W 10-100% Forward Phase
7. Turn Power On
V.2019.08.29
ZRK-EMLV2-200W-XXDC
5page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W

Forward
Phase
or Reverse
Phase
Dimming
Range
Input
Voltage
Model Number
(Dimmer)
Model Waage
CTCL-153PDH-LA 100-130V 0-100%Skylark Contour Forward Phase 150W
CT-600PR-WH 100-130V 0-100%Skylark Contour Forward Phase
600W
CT-103PR-WH 100-130V 2-100%Skylark Contour Forward Phase
1000W
SCL-153PR-WH 100-130V 0-100%Skylark Forward Phase
150W
S-600PR-WH 100-130V 0-100%Skylark Forward Phase
600W
SELV-300P 100-130V 15-100%Skylark Reverse Phase
300W
NTLV-600-277-WH 277V 1-100%Nova T Forward Phase
450W
SF-12P-277 277V 13-100%Skylark Forward Phase
6Amp
OTHERS COMPATIBLE DIMMERS
Forward
Phase
or Reverse
Phase
Dimming
Range
Input
Voltage
Model Number
(Dimmer)
Brand Waage
VPI06-1LZ 100-130V 15-100% Forward Phase 600W
Forward Phase
TTI06-1LZ 100-130V 1-100%600W
Forward Phase
IPL06 100-130V 15-100%150W
Forward Phase
DZ6HD 100-130V 17-100%600W
Forward Phase
6674 100-130V 16-100%Leviton 150W
Forward Phase
6672 100-130V 20-100%150W
Forward Phase
TBL03 100-130V 15-100%150W
Forward Phase
6602 100-130V 0-100%600W
Forward Phase
6683 100-130V 10-100%600W
Forward Phase
RHCL453PNICCV6 100-130V 6-100%-
Forward Phase
WSCL450TCCCV4 100-130V 11-100%Legrand 450W
Forward Phase
LSCL453PLACCV4 100-130V 11-100%450W
Reverse Phase
CNLW-DELVEX-P-W-S 100-130V 11-100%Crestron 500W
V.2019.08.29
ZRK-EMLV2-200W-XXDC
6page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W

L
N
AC
Input
Zurik EMLV Dimmable
Power Supply
Home Automation
System
Output
LED
AC Dimmer
(Lutron & Clipsal
C-Bus System)
L
N
AC
LN
Output
L
N
Input
Zurik EMLV Dimmable
Power Supply
LED
Output
L
N
Input
Zurik EMLV Dimmable
Power Supply
L
Output
L
N
Input
Zurik EMLV Dimmable
Power Supply
L
N
AC
Input
AC Dimmer
Zurik EMLV Dimmable
Power Supply
Output
LED
L
• Using a single driver
• Using mulple drivers
WIRING DIAGRAMS
V.2019.08.29
ZRK-EMLV2-200W-XXDC
7page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W

AC Dimmer
(Lutron & Clipsal
C-Bus System)
L
N
AC
LN
LED
L N
N
Output
L
N
Input
Black
Zurik EMLV Dimmable
Power Supply
Output
L
N Blue
Input
Zurik EMLV Dimmable
Power Supply
Output
L
N
Input
Zurik EMLV Dimmable
Power Supply
LUTRON
AC Dimmer
L
N
AC
LN
LED
DL/SL1
Output
L
N
Input
Zurik EMLV Dimmable
Power Supply
Output
L
N
Input
Zurik EMLV Dimmable
Power Supply
Output
L
N
Input
Zurik EMLV Dimmable
Power Supply
TROUBLESHOOTING
-If the driver is humming, lights are not turning on or are ickering:
•Check that this driver is not overloaded or overheated. The automatic breaker will trip and recover once the external cause has been corrected.
•Make sure the polarity of the AC line wires match the polarity of the channels on the Power Input Terminal.
•If the driver is powered, check the polarity on the Power Output Terminal. Make sure you have matched the markings on the LED strip to the
channels on the driver.
•Check that your dimmer is on the compatible dimmer list.
•Make sure all the connections (solderless connectors, solder joints, terminal blocks, and spliced wires) are secure and making correct contact.
•Make sure the power requirements are being met, 100-277VAC input and 12-24VDC output (depending on the driver), check these with a
multimeter.
•If the driver isn’t providing the adequate voltage ensure proper size gauge wire is installed by factoring voltage drop and amperage rating. If
the voltage at the end of the wire is 10.5V or less for a 12V unit and less than 21V for a 24V unit, we recommend installing a heavier gauge wire
between the driver and the LED load.
•Check that the wire connections are accurate by referring to the wiring diagrams provided.
•Check that your installation has not tripped the circuit breaker at the main service panel of the building. If this occurred reset the breaker. If it
trips again, it is possible that there is an electrical short/defective component or a connection issue on the AC side of the driver.
V.2019.08.29
ZRK-EMLV2-200W-XXDC
8page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W

Consumer’s Acknowledgment
Flexfire LEDs, Inc. stands behind its products when they are used properly and according to our specifications. When you purchase our
products, you are agreeing to the terms and conditions outlined in our warranty section. We try our best to make recommendations, but
the burden of proper installation, design, and maintenance relies on the purchaser.
This limited warranty does not include product failures that are the result of:
Not using a voltage regulated power supply to connect the LED product or controls; Connecting LED products to the wrong output
voltage; Improper connection of power supplies, LED products, or controls; Connecting LED products or controls directly to any AC
power source if they are stated for DC only input; Connecting power supplies backwards to an AC power source; Products used in an
inappropriate location or in environmental conditions (temperature, humidity, moisture, etc.) outside the normal specified range; Water
damage to products not specifically sold as waterproof products; Electrical power surges and spikes; Damage from hail, flooding, torna-
do, fire, wind, earthquake, lightning, electrical storm, or any other natural disasters or “force majeure” incidences; Damage caused by a
vehicle or other accident; Damage caused when transporting the item; Damage to any products that were modified by the user, used
for purposes other than as intended or directed, or connected to LED systems or components not purchased from Flexfire LEDs; Products
that have been subjected to misuse, mishandling, misapplication or accident. Products used in connection with any components, devic-
es or systems other than those explicitly approved as compatible with Company’s products and listed on Company’s website. Excessive
wear and tear and/or physical or accidental abuse, loss, or theft. Improper repairs or warranty services performed by someone other than
Flexfire LEDs will void this warranty.
WARRANTY INFORMATION
Limited Warranty:
This product has a 7 year limited warranty from the date of shipment. This warranty only includes the main product outlined in this speci-
fication sheet and does not include the additional accessories that are used as a reference. Complete warranty details for fixtures and
additional accessories are available at https://www.flexfireleds.com/warranties/ within the Policies section. For warranty related ques-
tions please contact product support team at (support@flexfireleds.com).
V.2019.08.29
ZRK-EMLV2-200W-XXDC
9page
support@FlexfireLEDs.com 925-273-9080 opt 2
User Guide •ZURIK®EMLV LED Driver 200W