ZyXEL Communications EMG2881-T20A User manual

EMG2881-T20A
Dual-Band Wireless AC1300
Gigabit Ethernet Gateway
Quick Start Guide
ENGLISH
Step 1 Desktop Installation
Step 2 Hardware Connections
Step 3 WiFi Connection
Copyright © 2018 Zyxel Communications Corp. All Rights Reserved.
EU Importer
Zyxel Communications A/S
Gladsaxevej 378, 2. th. 2860 Søborg, Denmark.
http://www.zyxel.dk
US Importer
Zyxel Communications, Inc
1130 North Miller Street Anaheim, CA 92806-2001
http://www.us.zyxel.com
See the User's Guide at www.zyxel.com for more information,
including customer support and safety warnings.
1 2
3 4
5 6
Connect the stand with the bracket holes facing up.
Place the device vertically on a smooth level surface.
1
2
EN
Use the blue Ethernet cable to connect the WAN port to a xDSL/Cable/Fiber modem.
Connect a computer to the LAN port using the Ethernet cable (optional).
Connect the power cable to the EMG2881-T20A and press the power button.
Check the LEDs.
3
4
5
6
EN
The SSID and Wireless Key are on the device label.
On your smartphone or notebook, find this SSID. Enter the Wireless key to connect.
EN
WAN
POWER
POWER
ON
OR
LAN
White ON - Power is on.
INTERNET
White
Off - Internet is not ready.
ON - Internet is ready.
POWER Off - Power is off.
POWER INTERNET WLAN
Using SSID
WiFi
Zyxelxxxxxx
Connect
SSID(2.4 GHz): Zyxelxxxxxx
SSID(5 GHz): Zyxelxxxxxx
Wireless Key: xxxxxxxxx
1/2

WPS
within
2minutes
WiFi
WPS
setup
Android Only
Amber Blinking - Connecting to 2.4GHz or
5GHz WiFi via WPS.
Off - WPS process is inactive.
WLAN
Using WPS
Web Configurator (Optional)
Wall Mounting (Optional)
Troubleshooting
Press the WPS button until the WiFi 2.4G and 5G LEDs light up in amber.
Press the WPS button on the client. If the WPS method fails, perform the Using SSID method.
EN
Open a web browser and go to http://192.168.1.1.
Enter the default Username (admin) and admin login password (on the device label), and then
click Login.
Go to System Status to check your Internet status.
Go to Configuration > WAN > Management WAN > Modify to set up your Internet.
Go to Configuration > WAN > Wireless > Wireless to change your SSID.
EN
(Optional) Drill two holes at the distance of 100mm apart. Insert screw anchors and screws (not
provided) into the holes. Attach the bracket to your EMG2881-T20A with the bracket holes
facing down. Hang it on the screws.
EN
EMG2881-T20A
Username
Password xxxxxxxxx
admin
Login
http://192.168.1.1
FCC ID I88EMG2881-T20A
IC 2468C-EMG2881T20A
IP Address: 192.168.1.1
Account: admin
Password: xxxxxxxxx
System Status
Interface Status
Configuration
• WAN
Management WAN
• --------
• --------
• --------
x2x2
100mm
The EMG2881-T20A doesn't turn on.
- Make sure you are using the power adaptor or cord included with the EMG2881-T20A.
- Make sure the power cable is connected.
- Make sure the power adaptor is connected to an appropriate power source. Make sure the power source is turned on.
I cannot see or access the Login screen in the Web Configurator.
- Make sure you are using the correct IP address.
• The default IP address is 192.168.1.1.
• If you changed the IP address, use the new IP address.
• If you changed the IP address and have forgotten it, you have to reset the device to its factory defaults.
- Check the hardware connections, and make sure the LEDs are behaving as expected.
- Make sure your Internet browser does not block pop-up windows and has JavaScript enabled.
- Make sure your computer and the EMG2881-T20A are in the same subnet.
- Make sure you have entered the Username and Password correctly.
The default Username is admin, and the default Password is assigned randomly (on the device label). If this does not work, you have to reset the EMG2881-T20A to its factory defaults.
I cannot access the Internet.
- Check the hardware connections and the LED behavior.
- Make sure the WAN port is connected to a broadband modem or router with Internet access. Your computer and the EMG2881-T20A should be in the same subnet.
- Make sure you entered your ISP account information correctly.
- If you are trying to access the Internet wirelessly, make sure that you enabled the wireless LAN in the EMG2881-T20A and your wireless client. Make sure you use the same wireless settings in the
wireless client and the EMG2881-T20A.
- Disconnect all the cables from your EMG2881-T20A and reconnect them.
2/2
1
2
More than
1 second