ZyXEL Communications P-660HWP-D1 User manual

Copyright © 2007. All rights reserved.
P-660HWP-Dx
802.11g HomePlug AV ADSL2+ Gateway
Quick Start Guide
Version 3.40
7/2007
Edition 1

P-660HWP-Dx Quick Start Guide
1
Overview
The P-660HWP-Dx is a gateway which combines high-speed ADSL Internet access, a
built-in switch, a firewall, and HomePlug AV and high-speed wireless networking
capability.
The figure below shows the P-660HWP-Dx connecting devices via a firewalled DSL
connection to the Internet through:
• standard electrical wiring and HomePlug AV adapters (“A”)
• wireless
• direct, wired connections using the P-660HWP-Dx’s built-in switch.
The P-660HWP-Dx is also a firewall, providing greater security for your local network(s).
This Quick Start Guide shows you the most common settings for connecting to the
Internet, configuring your wireless settings and setting up your HomePlug AV network.
For more information on all features see your User’s Guide on the CD that came in the
package.
To read the User’s Guide insert the CD that came in the box into your CD-ROM drive. A
screen should pop up. Navigate to the User’s Guide from this screen. If a screen does not
pop up, open Windows Explorer (click My Computer), click on the CD-ROM drive (usually
drive D:) and navigate to it from there.

P-660HWP-Dx Quick Start Guide
2
1 Hardware Connections
1DSL: Use the gray telephone wire to connect your P-660HWP-Dx’s DSL port to a
telephone jack (or to the modem port on a splitter if you are using one).
2ETHERNET: Use the yellow Ethernet cable to connect a computer to an ETHERNET
port on the P-660HWP-Dx for initial configuration and/or Internet access.
3POWER: Use only the power cable that came in the package to connect your P-
660HWP-Dx to a power outlet. Make sure the power outlet is switched on. This socket
will also act as your HomePlug AV connection.
4Push in the POWER button.
5Look at the lights on the front panel.
•ThePOWER light (LED) blinks while your P-660HWP-Dx starts up and stays on once it is
ready.
•TheETHERNET, WLAN, DSL, INTERNET and POWERLINE LEDs turn on if the corre-
sponding connections are properly made.
VCheck your connections if an LED does not turn on. Then turn the P-
660HWP-Dx off, wait for a few seconds and turn it back on. See
Troubleshooting. If the problem remains, contact your local vendor.
2 Internet Connection Setup: Automatic
Use this section to have your P-660HWP-Dx automatically detect and set up your Internet
connection.

P-660HWP-Dx Quick Start Guide
3
1Open a browser such as Internet Explorer and go to your favorite website. Wait while
your P-660HWP-Dx tries to detect your DSL connection to your ISP. This may take a
few minutes.
2After it detects the connection, the DSL light shows green on your device and the
Internet light comes on when the Internet is ready for you to use. If you have a PPPoE
connection, you will have to enter your user name and password.
3Go to section 3 if you wish to configure your wireless settings using the wizard.
4If you do not see the connection test screen, or the connection test is not successful,
follow the instructions in the screen below, or check your connections and restart the P-
660HWP-Dx.
3 Internet and Wireless Setup Wizard
Use this wizard to connect to the Internet and configure your wireless settings
3.1 Log In to the Wizard
Default Login Information
1Open a browser such as Internet Explorer and enter the following URL address: http://
192.168.1.1
2Type the admin password 1234 (default). Click Login.
• If your browser does not display the login screen, see Troubleshooting for details.
3Type (and retype) a new password and click Apply. It is strongly recommended that
you change the P-660HWP-Dx’s password and write it down.
You have to use a new password other than the default password 1234.
IP address http://192.168.1.1
administrator password 1234

P-660HWP-Dx Quick Start Guide
4
4Enter your new password to log in again.
5Click Apply in the screen below to create a new certificate for your P-660HWP-Dx. This
screen will continue to appear until you apply this option.
6Select Go to Wizard setup in the screen below. Click Apply to access the Wizard.
3.2 Connect to the Internet Using the Wizard
1Click INTERNET/WIRELESS SETUP. The wizard autodetects your Internet connection.
• If the Internet connection test is successful, you are ready to use the Internet. Go to
section 3.3 if you wish to configure your wireless settings using the wizard.
• If no DSL connection is detected, see Troubleshooting.
• If no ISP settings are detected, click Next in the current screen to go to the screen
below.
2Enter your Internet connection information exactly as provided by your ISP in the
screen below and click Next.

P-660HWP-Dx Quick Start Guide
5
• If you do not see the screen below, or your ISP has given you Internet access set-
tings not available on this screen, see Troubleshooting.
3In the next screen, select either Obtain an IP Address Automatically or Static IP
Address. If you select Static IP Address then fill out the required fields based on the
information provided by your ISP and click Apply.
4If the Internet connection test is successful, either browse to your favorite website
(such as www.zyxel.com) or click Next on your screen to go to section 3.3 to configure
your wireless settings.
3.3 Configure your Wireless Settings Using the Wizard
To create a wireless network the P-660HWP-Dx and your wireless computer(s) must all
use the same SSID (network name), channel and security settings.
If you do not set wireless security then anyone within range could use your P-660HWP-Dx
to access your network and the Internet.
Choose WPA-PSK wireless security if your wireless device supports it as it is stronger than
WEP.

P-660HWP-Dx Quick Start Guide
6
1Select Active and click Next to continue. It is strongly recommended that Enable
OTIST is NOT selected. See the Users’ Guide for more information on OTIST.
2Configure your wireless settings in the screen displayed. Click Next.
3If you select either WEP or WPA-PSK security (recommended), then follow the directions
to enter the appropriate key. Click Next to continue and Apply to save your wireless LAN
settings.
4Check your configuration in the screen below and write down your wireless LAN settings
for later use.

P-660HWP-Dx Quick Start Guide
7
5Click Finish to complete and save the wizard setup. Your Internet connection is ready for
you to use. Open a browser such as Internet Explorer and navigate to a website.
4 Setting Up a Wireless Network
To set up a wireless network you need at least one wireless network card/adapter.
• If you have a desktop computer, use either a wireless USB adapter or a wireless PCI
adapter.
• If you have a laptop, use either a wireless USB adapter or a wireless CardBus card. These
are built into many laptops.
To add a computer to your network you need to configure your wireless-enabled computer
with the same SSID, channel and security settings as the P-660HWP-Dx.
Alternatively, use OTIST, ZyXEL's One-Touch Intelligent Security Technology (OTIST)
feature. It allows you to automatically configure the SSID and WPA-PSK on all OTIST-
equipped wireless clients within range of the P-660HWP-Dx. See the Wireless LAN
chapter in the Users’ Guide for more information on OTIST.
5 HomePlug AV Network Setup
Follow these steps to set up your HomePlug AV network on standard electrical wiring with
a new password.
1Plug your P-660HWP-Dx and other HomePlug AV devices into power outlets and turn
them on. Your P-660HWP-Dx will try to detect other HomePlug AV devices on the
same electrical wiring.
2Check the POWERLINE ( ) LED for a HomePlug AV connection.
• If the LED does not display, your device has a problem detecting another HomePlug AV
device. Go to Troubleshooting for more information.
• If the LED light is green, the P-660HWP-Dx detects other HomePlug AV devices and you
are ready to set up your network.
You need to configure the power line settings of the P-660HWP-Dx, as well as the power
line settings of the other devices you wish to add to your network.
3Go to Network > Powerline > Local Setting to configure the P-660HWP-Dx’s power
line settings.
• Select Enable Powerline.

P-660HWP-Dx Quick Start Guide
8
• Type the Network Password for your network. This will connect you to other Home-
Plug AV devices which have the same password and allow you to configure them.
HomePlugAV is the default password for ZyXEL HomePlug AV devices.
• You do not need to type the Device Access Key (DAK) for the P-660HWP-Dx unless
you want to change it.
• Click Apply.
4Go to Network > Powerline > Remote Setting to make a new network with a new
Network Password and add the other HomePlug AV devices to your new network.
• Select a device listed in Remote Stations In The Same Network and type a new
Network Password.
• Type the Device Access Key (DAK) in the Login Remote Device Access Key field.
The DAK identifies each device. For ZyXEL HomePlug AV products the DAK is on
an attached label. Click Apply. The device disappears from the list of Remote Sta-
tions In The Same Network. With a different password it now is on a different net-
work.
• Repeat for all devices you want to add to your network.
5Go back to Network > Powerline > Local Setting to change your P-660HWP-Dx’s
Network Password to the new one and connect it to your new HomePlug AV network.
Type your new Network Password and click Apply.
6Check the other devices you selected previously are now on the list of Remote
Stations In The Same Network by going to Network > Powerline > Remote Setting. If
all devices are correctly listed, your HomePlug AV network is now ready for use.

P-660HWP-Dx Quick Start Guide
9
Troubleshooting
VIf you cannot access the web configurator check the following.
1Your computer may be set to use a static IP address in a different subnet from the
ZyXEL device. See the User’s Guide for information on setting up your IP address.
2If you are using Internet Explorer in Windows XP or Windows Server 2003, make sure
you allow pop-up windows, JavaScript and Java permissions or set the Internet security
level lower than High in Internet Explorer (in Internet Explorer, click Tools > Internet
Options > Security > Custom Level...). See the appendix in the User’s Guide for more
information.
VIf the Internet/Wireless Setup Wizard cannot detect a DSL connection
check the following.
1Check your connections and restart the device.
2Contact your ISP to check the status of your account.
VIf you do not see the ISP Parameters for Internet Access screen when you
run the Internet/Wireless Wizard, follow these steps.
1Log in to the P-660HWP-Dx’s web configurator. (See section 3.1.)
2Select Go to Advanced setup and click Apply.
3The Status screen appears. Click Network > WAN in the navigation panel on the left of
the screen.
4Ensure that the settings in this screen are the same as those your ISP gave you. If your
ISP gave you a static IP address to use, select Static IP Address in the IP Address