ZyXEL Communications P-2302HW-P1 Series User manual

P-2302HW/HWL-P1
802.11b/g Wireless VoIP Station Gateway
Quick Start Guide
Version 3.60
Edition 1
8/2006

P-2302HW/HWL-P1 Series Quick Start Guide
2
1 Connect the Hardware
1WAN: Use an Ethernet cable to connect the DSL modem to this port.
2LINE(P-2302HWL models only): Use the green PSTN line cable to connect the TEL or PHONE jack on a
splitter to this port. If no splitter is provided connect the the telephone jack to this port.
Note: When the P-2302HWL-P1 does not have power, only the phone connected to the PHONE 1 port
can be used for making calls. Ensure you know which phone this is, so that in case of emergency
you can make outgoing calls.
3ETHERNET: Use an Ethernet cable to connect a computer to this port for initial configuration and/or
Internet access.
4 PHONE 1-2: Use telephone cables (and any telephone adaptors provided with your P-2302HW/HWL-P1)
to connect your telephones to these ports. If you only have one telephone, you should use port 1.

P-2302HW/HWL-P1 Series Quick Start Guide
3
5POWER:Use the power adaptor provided with your P-2302HW/HWL-P1 to connect an appropriate power
source to this socket.
1.1 LEDs (Lights)
•ThePOWER light blinks during start-up and is green once the P-2302HWL-P1 is ready.
• Each ETHERNET light turns on if the corresponding ETHERNET port is properly connected.
The lights blink when the P-2302HWL-P1 is sending or receiving data through the correspond-
ing ETHERNET port.
•TheWAN light stays on if a physical connection with your DSL modem exists. The INTERNET
light stays on when Internet access is available.
•ThePHONE lights stay on when your SIP account is registered and they blink if the receiver is
off the hook.
•TheWLAN light turns on when the wireless LAN is ready. It blinks when the P-2302HWL-P1 is
sending/receiving data through the wireless LAN.
2 Initial Configuration
If none of the LEDs are on, turn the device off and
recheck your hardware connections.
1Open your browser, and go to http://192.168.1.1.2Enter the password 1234. Then, click Login.

P-2302HW/HWL-P1 Series Quick Start Guide
4
2.1 Connection Wizard
The connection wizard helps you set up your Internet
connection as well as your wireless settings. Click
CONNECTION WIZARD.
.
Note: Enter the Internet access information exactly
as given to you by your ISP in each wizard
screen and then click Next to continue or click
Back to return to the previous screen.
Current screen information will be lost if you
click Back.
3Follow the directions in this screen. 4Click Go to Wizard setup.

P-2302HW/HWL-P1 Series Quick Start Guide
5
STEP 1: System Information
STEP 2: Wireless LAN
A Select None for your initial wireless security.
B Select No in the Do you want to enable OTIST ? radio button.
Note: These settings allow you to access the wireless network without setting up any security on your
wireless client. This means that any wireless device within range of your P-2302HW/HWL-P1
can access your wireless network.
If you know the security settings you want to set up you can also enter them in these screens. If
you want to set up OTIST, see the following section. Refer to your User’s Guide for more
information on setting up your wireless network.
This screen is optional. You can just click Next.
•System Name is for identifying the P-2302HW/
HWL-P1. You can enter your computer's "Com-
puter Name".
• If you leave the Domain Name blank, the domain
name obtained by DHCP from the ISP is used.
A
B

P-2302HW/HWL-P1 Series Quick Start Guide
6
OTIST
ZyXEL's One-Touch Intelligent Security Technology (OTIST) feature allows you to automatically configure the
SSID and WPA-PSK on all OTIST-equipped wireless clients within range of the P-2302HW/HWL-P1.
Note: If you enable OTIST but select Disable wireless security using the wireless wizard, the P-
2302HW/HWL-P1 will create a WPA-PSK automatically.
If you enable OTIST and select Manually assign a WEP key using the wireless wizard, the P-
2302HW/HWL-P1 will replace the WEP key with a WPA-PSK.
Enable OTIST only if your wireless clients support WPA and OTIST.
You must enable OTIST on the P-2302HW/HWL-P1 and all wireless clients within three minutes in any order.
To enable OTIST on wireless clients, click Start in the Adapter screen. The Setup Key is 01234567 by default.
If you have previously saved a setup key on the P-2302HW/HWL-P1, use it instead of the default.
STEP 3: WAN
Select one connection type from the drop-down list box. Check with your ISP to make sure you use the correct
type:
1Ethernet
2PPPoE
Note: If you were given Internet access settings, enter them in the following fields. Otherwise leave the
default settings and just click Next.

P-2302HW/HWL-P1 Series Quick Start Guide
7
A Select Ethernet as your WAN connection type.
B Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to C.
Or
Select Use fixed IP address provided by your ISP to give the P-2302HW/HWL-P1 a fixed, unique IP
address. Go to B1.
B1 If you select Use fixed IP address provided by your ISP,enter a WAN IP address, WAN IP Subnet Mask
and the neighboring device’s IP address given by your ISP.
If you were given DNS server settings, enter them in the fields. Otherwise leave the default settings and
just click Next.
C Select Factory Default to use the factory assigned default MAC address. Click Apply to save your changes.
The OTIST in Progress screen appears if you enable OTIST in the previous wizard screen. Wait for the P-
2302HW/HWL-P1 to finish transferring OTIST settings.
D Click Finish to complete the wizard.
Ethernet Connection

P-2302HW/HWL-P1 Series Quick Start Guide
8
A
B
C
B1

P-2302HW/HWL-P1 Series Quick Start Guide
9
A Select PPPoE as your WAN connection type.
B Type a Service Name (Optional), User Name and Password.
C Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to D.
Or
Select Use fixed IP address provided by your ISP to give the P-2302HW/HWL-P1 a fixed, unique IP
address. Go to C1.
C1 If you select Use fixed IP address provided by your ISP,enter a WAN IP address, WAN IP Subnet Mask
and the neighboring device’s IP address given by your ISP.
If you were given DNS server settings, enter them in the fields. Otherwise leave the default settings and
just click Next.
D Select Factory Default to use the factory assigned default MAC address. Click Apply to save your changes.
The OTIST in Progress screen appears if you enable OTIST in the previous wizard screen. Wait for the P-
2302HW/HWL-P1 to finish transferring OTIST settings.
E Click Finish to complete the wizard.
PPPoE Connection

P-2302HW/HWL-P1 Series Quick Start Guide
10
3 Configure VoIP
Click VOIP SETUP.
Note: You should have the information provided by
your VoIP service provider.
Enter the information provided by your VoIP service
provider. Keep the default settings if your VoIP service
provider did not provide some information. If you have a
SIP account like [e-mail], the SIP
Number is 1234567, and the SIP Service Domain is VoIP-
provider.com. When you are done, the PHONE light
should be on. Close the wizard.
A
B
C
C1
D