ZyXEL Communications P-660HN-51 - User manual

www.zyxel.com
802.11n Wireless ADSL2+ 4-port
Gateway
Firmware Version 1.10
Edition 1, 9/2010
P-660HN-51
DEFAULT LOGIN DETAILS
IP Address: http://192.168.1.1
User Name: admin
Password: 1234
Copyright 2010
ZyXEL Communications Corporation

2
Device Panels
POWER
LAN1-4
INTERNET
WPS/WLAN
DSL
RESET
LAN PORT 1-4
POWER
DSL PORT

P-660HN-51
3
Overview
The P-660HN-51 is an ADSL2+ router with a four-port built-in Ethernet
switch and IEEE 802.11n wireless capability. The P-660HN-51 allows
wired and wireless clients to safely access the Internet. The built-in
firewall blocks unauthorized access to your network. It supports other
helpful features, including Quality of Service (QoS) which allows time-
sensitive services and applications to flow more smoothly.
Connect the Stand
Either place the P-660HN-51 flat on a desk or table or use the stand for a
vertical installation. To connect the stand, line up the arrow on the stand
with the arrow on the bottom of the device as shown.

4
Hardware Connections
This section shows you how to set up your P-660HN-51.
1. DSL: Use a telephone cable to connect your P-660HN-51’s DSL port
to a telephone jack (or to a splitter, if one is already installed).
2. LAN: Use an Ethernet cable to connect a computer to a LAN port for
initial configuration and/or Internet access.
3. POWER: Use the power adaptor provided with your P-660HN-51 to
connect an appropriate power source to the POWER socket. Make
sure the power at the outlet is on. After connecting the power adapter,
look at the lights on the front panel.
2
1
3

P-660HN-51
5
• The POWER light blinks while your P-660HN-51 starts up and then
stays on once it is ready. The DSL light turns on when the P-
660HN-51 has a DSL connection. The WPS light turns on when the
wireless LAN is ready. The INTERNET light turns on when the
gateway is able to access the Internet and will blink when the P-
660HN-51 is sending or receiving data.
• Each LAN light stays on if the corresponding LAN port is properly
connected and blinks when there is traffic.
If the POWER, DSL, or connected LAN lights are not on, please check
your connections and inspect your cables for damage. If the lights are
still off, contact technical support.
Set Up a Wireless Network
The wireless LAN on your P-660HN-51 is enabled by default. To add a
wireless client to the network, refer to the settings sticker that comes with
your P-660HN-51, which will look similar to the following example:
Configure wireless devices that you want to connect to the wireless
network to use the same wireless settings as the P-660HN-51.
The default wireless settings vary for each P-660HN-51. Refer to the
settings sticker of your device and use the provided information.
SSID: ZyXEL00561
WPA: FB373BD356

6
Log into the Web Configurator
Your device may already be set up for Internet access. However, you
may want or need to log on to the P-660HN-51 web configurator to
perform tasks:
• Configure your Internet access settings manually
• Customize the Quality of Service (QoS) and routing features
• Enable firewall and create filter rules
• Edit remote management, as well as other features
1. In your browser, go to http://192.168.1.1.
2. Enter the default user name admin and password 1234. Click Login.
If the login screen does not open, make sure you allow web
browser pop-up windows, JavaScript and Java permissions.
Your computer should be also set to get an IP address
automatically from a DHCP server. See your User’s Guide
for more information.

P-660HN-51
7
3. A welcome screen appears showing a summary of your last login.
Select Show this page next time to see the welcome screen on your
next login. Otherwise, deselect it. Click Continue.
4. The Network Map page appears. This shows whether the P-660HN-
51 and computers/devices connected to it have Internet access.

8
Click on Status to display the following screen, where you can view the
P-660HN-51 device, interface and system information.
5. If the DSL light is turned off, manually configure the Internet
connection Click Network Settings > Broadband, then click Add
new WAN Interface.
• Select Active to activate the WAN configuration and enter the
connection name.
• Select the Internet mode (Routing) and encapsulation (PPPoE)
used by your ISP.
• Type your account username and password.
• Type your static IP address and DNS server if they are not assigned
automatically to your account. Click Apply.

P-660HN-51
9
See the User’s Guide on the CD for all configuration details.
Internet
Account

10
Using Wireless Protected Setup
(WPS)
If your wireless devices display the WPS logo, you
can use Wi-Fi Protected Setup (WPS) to add
wireless devices to your wireless network. If your
wireless devices do not display the WPS logo, go to
Set Up a Wireless Network on page 5to manually set up a wireless
network.
You must enable the WPS function before using the WPS button.
1. Log into the Web Configurator (see page 5for more information).
Then click Network Settings > Wireless > WPS to go to the WPS
screen.
2. Select Enable and click Apply.